diff --git a/FAQ/images/TS_plugin_TCP.png b/FAQ/images/TS_plugin_TCP.png
new file mode 100644
index 00000000..8a9f83e9
Binary files /dev/null and b/FAQ/images/TS_plugin_TCP.png differ
diff --git a/Ford-Fox-Body-(88-Ford-Mustang---302-V8).textile b/Ford-Fox-Body-(88-Ford-Mustang---302-V8).textile
new file mode 100644
index 00000000..8c8b6e29
--- /dev/null
+++ b/Ford-Fox-Body-(88-Ford-Mustang---302-V8).textile
@@ -0,0 +1,35 @@
+
+Mechanical distributor - single not smart two wire coil.
+
+Solenoid idle air control.
+
+8 injectors wired separately.
+
+
+rusEFI Car MRE Desc Connection Type
+2 20 Ground Main Ground Ground
+3 21 IAC Idle Air Controler Sensor
+5 37/57 12v + Main Power Positive Power in
+7 ??? Shift Light Ground
+9 14 IGN1 Injector 5 Ground
+10 15 IGN2 Injector 6 Ground
+11 42 IGN3 Injector 7 Ground
+12 52 IGN4 Injector 8 Ground
+15 USB D - Negative USB White Wire
+16 USB D + Positive USB Green Wire
+17 SGND Signal Ground USB Black Wire
+18 07 CLT / ECT Engine Coolant Temp Sensor
+23 IAT Intake Air Temp Sensor
+25 Cam (hall) Cam Sensor 1 Sensor
+26 47 TPS Throttle Position Sensor
+27 MAP Manifold Air Pressure Sensor
+32 EGT Exhaust Gas Temp (AEM) Sensor
+37 58 INJ 1 Injector 1 Ground
+38 59 INJ 2 Injector 2 Ground
+41 12 INJ 3 Injector 3 Ground
+42 13 INJ 4 Injector 4 Ground
+44 5v + 5 volt sensor Power 5v + Power Output
+45 Crank VR+/hall Cam Sensor 2 Sensor
+
+
+"88-91 ECU Diagram":http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif
\ No newline at end of file
diff --git a/HOWTO-Remote-Tuning.md b/HOWTO-Remote-Tuning.md
new file mode 100644
index 00000000..65943ba8
--- /dev/null
+++ b/HOWTO-Remote-Tuning.md
@@ -0,0 +1,11 @@
+Remote tuning is possible over Internet using rusEFI TunerStudio plugin if rusEFI ECU is connector to the internet.
+
+There are three ways to connect rusEFI to internet:
+1) Coming soon: "Broadcast" tab of rusEFI TunerStudio plugin.
+2) rusEFI network_connector tool running for instance on Raspberry Pi
+3) Coming soon: rusEFI Android application.
+
+Connecting to remote ECU is a two step process:
+First you connect rusEFI TunerStudio plugin to remote controller via Internet, and then you connect TunerStudio to rusEFI TunerStudio plugin locally. IP Address "localhost" Port default value 29001.
+
+
\ No newline at end of file
diff --git a/Hardware/microrusefi/Hardware_microRusEfi_kit_instructions.md b/Hardware/microrusefi/Hardware_microRusEfi_kit_instructions.md
index 17ee9310..a82d82d4 100644
--- a/Hardware/microrusefi/Hardware_microRusEfi_kit_instructions.md
+++ b/Hardware/microrusefi/Hardware_microRusEfi_kit_instructions.md
@@ -17,6 +17,10 @@ If in double of your SMD skills please consider fully assembled version.
For component placement please use interactive BOM
+[0.5.2](https://rusefi.com/docs/ibom/micro_rusEFI_R0.5.2.html)
+
+[0.5.1](https://rusefi.com/docs/ibom/micro_rusEFI_R0.5.1.html)
+
[0.5.0](https://rusefi.com/docs/ibom/micro_rusEFI_0.5.0.html)
[0.4.8](https://rusefi.com/docs/ibom/microRusEfi_R0.4.8.html)
diff --git a/Images/Miata_NA_VAF.png b/Images/Miata_NA_VAF.png
new file mode 100644
index 00000000..1f5b1672
Binary files /dev/null and b/Images/Miata_NA_VAF.png differ
diff --git a/MREAdapter48.md b/MREAdapter48.md
index 1663d6ea..ca88d836 100644
--- a/MREAdapter48.md
+++ b/MREAdapter48.md
@@ -1,13 +1,15 @@
+[SEE ALSO](Miata-NA-48-pin-board-for-MRE-(version-0.2))
+
High-side jumper should be set for +12v.
-Created for 1989-1995 Mazda Miata NA6 and early NA8. Would also work on Mazda Protege, Ford Festiva, Ford Escort GT and probably other relted vehicles.
+Created for 1989-1995 Mazda Miata NA6 and early NA8. Would also work on Mazda Protege, Ford Festiva, Ford Escort GT and probably other related vehicles.
See also [Miata](Miata)
microRusEFI should be set for Hall
-[Schematics 0.2](https://github.com/rusefi/rusefi_documentation/raw/master/Hardware/pnp_microRusEfi_48na/microrusefi48adapter_0.2.pdf)
+[Schematics 0.2](https://github.com/rusefi/rusefi_documentation/raw/master/Hardware/pnp_microRusEfi_48na/microrusefi48adapter_0_2.pdf)
[Schematics 0.1](https://github.com/rusefi/rusefi_documentation/raw/master/Hardware/pnp_microRusEfi_48na/microrusefi48adapter_0.1.pdf)
diff --git a/Miata-NA-48-pin-board-for-MRE-(version-0.2).md b/Miata-NA-48-pin-board-for-MRE-(version-0.2).md
index ddb4a3f0..2fb0f2e4 100644
--- a/Miata-NA-48-pin-board-for-MRE-(version-0.2).md
+++ b/Miata-NA-48-pin-board-for-MRE-(version-0.2).md
@@ -64,3 +64,9 @@ Instructions on how to jumper the board for these configurations will be updated
# 4. Connections
Expansions usually require some wiring. The standard pinout for the connector in NA6 configuration is this below.
+
+# 5. Assemble your own
+If you just get the bare board with all the jumpers installed, there's some things you need to do.
+
+## 5.1. MAP Sensor
+There are two positions for installing a MAP sensor on the board. The sensors used are [MPX4250](https://www.digikey.com/product-detail/en/nxp-usa-inc/MPX4250AP/MPX4250AP-ND/464053). They should be secured with two screws each. [4-40 x 0.5 socket head cap screws](https://www.mcmaster.com/92196A110/) are preferred. Of course, these screws will require some [nuts](https://www.mcmaster.com/91841A005/).
\ No newline at end of file
diff --git a/Pages_Sensors_and_Actuators.md b/Pages_Sensors_and_Actuators.md
index bc3b3707..9a1a93cf 100644
--- a/Pages_Sensors_and_Actuators.md
+++ b/Pages_Sensors_and_Actuators.md
@@ -15,14 +15,14 @@
* [Fuel Overview](Fuel_Overview)
* List of tested MAP sensors - Coming Soon
+* [GM Map sensor](GM-map-Sensor)
MAF Sensors
-* [GM Map sensor](GM-map-Sensor)
-* List of tested MAP sensors - Coming Soon
+* [List of tested MAP sensors](Vault_Of_Sensors)