mirror of https://github.com/speeduino/wiki.js.git
docs: update boards/official/TurbineBear
This commit is contained in:
parent
47953892cc
commit
f4551af063
|
@ -2,27 +2,18 @@
|
|||
title: Turbine Bear
|
||||
description:
|
||||
published: true
|
||||
date: 2021-08-25T04:16:09.931Z
|
||||
date: 2021-08-25T05:42:10.592Z
|
||||
tags:
|
||||
editor: markdown
|
||||
dateCreated: 2021-08-25T01:57:06.706Z
|
||||
---
|
||||
|
||||
# Dropbear ECU
|
||||
The Dropbear is an 8 fuel + 8 ignition ECU that is currently in testing prior to a full production release. It is powered by the high speed Teensy 3.5 board and is designed to be a complete unit out of the box.
|
||||
# Turbine Controller
|
||||
Blah blah
|
||||
|
||||
## Features
|
||||
|
||||
- 8x high impedance injector drivers
|
||||
- 8x 5v/12v coil pre-drivers (For use with igniters/smart coils)
|
||||
- 6x medium current (2A) outputs
|
||||
- 7x analog inputs
|
||||
- 4x digital inputs
|
||||
- CAN transceiver
|
||||
- Onboard VR conditioner
|
||||
- Swappable internal MAP sensors
|
||||
- Onboard baro sensor
|
||||
- Optional stepper motor driver
|
||||
Blah
|
||||
|
||||
## Board Configuration
|
||||
The Dropbear board contains 4 switches and 1 DIP switch pair that can be used to change the setup of the ECU.
|
||||
|
@ -54,24 +45,10 @@ Recommended values for the filters are shown below (By default both switches wil
|
|||
{.is-warning}
|
||||
|
||||
|
||||
### MAP Selector
|
||||
The Dropbear board uses a removable MAP card containing the sensor and a short hose running to the bulkhead connector on the enclosure. Currently only the default 0-250kpa sensor board is available, with higher range boards to be made available in the future. To use this MAP card, select the `Int.` (Internal) option on the MAP switch.
|
||||
|
||||
If you wish to use an external MAP sensor located in the engine bay, this switch should be to to `Ext.` and the sensors signal line should be connected to pin `C8` on the Black connector. The MAP card can be left in place or removed when the `Ext.` option is used.
|
||||
|
||||
### Stepper Driver
|
||||
By default the Dropbear unit is designed for use with PWM idle valves, however an optional stepper motor driver can be fitted.
|
||||
|
||||
> Please note that using the stepper driver requires pins C3 through C6 on the grey connector. Other output functions cannot use these pins when a stepper driver is installed
|
||||
{.is-warning}
|
||||
|
||||
The board has a socket to install a standard DRV8825 stepper motor driver if required. It should be installed in the following orientation if needed:
|
||||
![drv8825_dropbear_fitment.jpg](/img/idle/drv8825_dropbear_fitment.jpg){.align-center width=400}
|
||||
|
||||
|
||||
## Pin out
|
||||
|
||||
The Dropbear ECU uses 2x 24 pin Delphi Sicma connectors. The connectors are keyed and will only connect to the matching colour loom plug.
|
||||
The ECU uses 2x 24 pin Delphi Sicma connectors. The connectors are keyed and will only connect to the matching colour loom plug.
|
||||
|
||||
### Black Connector
|
||||
![Delphi SICMA Black Connector](/img/boards/Connector_black.png){.align-center width=400}
|
||||
|
|
Loading…
Reference in New Issue