7c6974ab43
Fixes after clenup ( #2019 )
...
* We still need consoleEventListener for boards with EFI_CONSOLE_SERIAL_DEVICE
* MC33810: add MC_ prefix for command defines
As CMD_PWM define is now used by console command
2020-12-05 11:54:09 -05:00
f3b7a1d9da
Remove lockAnyContext, replace with CriticalSectionLocker ( #1938 )
...
* switch to CriticalSectionLocker
* that's just about all
* clean up last usage
* include hpp for sim
* need the cpp wrappers in the makefile too
* include dir
* include
2020-11-19 06:56:02 -05:00
f48621e4c2
TLE8888: disable diagnostic for OUTPUT8..13 ( #1956 )
...
Enabled pull-down affects analog inputs that shares same pins.
Disable it.
DOTO: enable diagnostic if ouput requested through tle8888_setPadMode
2020-11-17 18:33:37 -05:00
62f441376c
Tle8888 stepper ( #1936 )
...
* TLE8888: enable PP mode for OUT21..24 in case of useTLE8888_stepper
* Lada Kalina is a test mule for stepper idle
2020-11-10 14:16:46 -05:00
63c25ab8a7
Tle8888 small update ( #1908 )
...
* TLE8888: add support MR switching from SW
Main Relay has limitation - it is always active while KEY=1. When
KEY=0 MR can be switched on from SW.
* TLE8888: support reading of KEY and WAKE inputs
* Rusefi enums: add new TLE8888 pins
2020-11-01 22:19:55 -05:00
8e11675afd
Tle8888 big update 1 ( #1892 )
...
* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
2020-10-23 12:25:30 -04:00
02573713f3
Hellen says drivers
2020-09-07 12:00:16 -04:00
e3b41c2387
dead code
2020-08-31 20:52:25 -04:00
fc28692258
more readable error message thank you Matt!
2020-05-23 17:20:46 -04:00
44b5e38d3a
"TLE8888 SR Unexpected response" does not work as intended fix #1466
2020-05-22 22:56:19 -04:00
a0a1a9f9bb
"TLE8888 SR Unexpected response" does not work as intended #1466
2020-05-22 08:23:49 -04:00
c95a4c552b
more info into error message
2020-05-22 01:05:07 -04:00
7500e44c8c
tle6240: fix crash in driver wake routine ( #1435 )
2020-05-15 15:54:41 -04:00
4e5a69891d
new LED logic: constant WARNING if VBATT is below 7v
2020-05-13 01:52:27 -04:00
257ed04fac
new LED logic: constant WARNING if VBATT is below 7v
2020-05-13 01:17:48 -04:00
52ad619b15
I think it's OK to crash very visibly if no proper SPI response
2020-05-13 01:07:11 -04:00
75781f1262
hiding diag code which was messing with GP2/GP3 i.e. TLE8888_PIN_22 TLE8888_PIN_23
2020-05-11 00:53:50 -04:00
633afc10c8
trying to guess
2020-05-09 20:45:20 -04:00
19a1ad05b1
tle8888 restoration
2020-05-09 16:59:54 -04:00
b88b1e4aa5
mre 050 compromise
2020-05-09 09:40:00 -04:00
8c3485a8dc
Revert "Tle8888 for mre 050 ( #1408 )"
...
This reverts commit ba1a606d
2020-05-08 23:58:34 -04:00
ba1a606d9a
Tle8888 for mre 050 ( #1408 )
...
* tle8888: fix tle8888_chip_init flow
* tle8888: set correct pin modes for mcu gpios in tle8888_chip_init
Direct drive, reset, inj_en and ign_en gpio should be outputs
2020-05-08 19:05:30 -04:00
d0d5cdd4dd
tle8888: on MRE 0.5.0 we can drive ING_EN and INJ_EN from STM ( #1407 )
...
Do it!
2020-05-08 17:47:41 -04:00
98bca0cb23
Tle8888 stage 1 ( #1404 )
...
* TLE8888: implement diagnostic
* TLE8888: add support for PP mode on OUT21..24
* tle8888: use helpers to extract register value from 16bit reply
2020-05-07 09:49:57 -04:00
5987fb8b88
[SAFE] Debug cleanups ( #1403 )
...
* electronic throttle: inprove debug
* idle thread: show debug info for configured idle driver
* gpio-chips: make private functions static
2020-05-06 20:06:50 -04:00
07e6e2c4ad
steps towards tle8888
2020-05-06 19:20:12 -04:00
c52c7e2f1f
TLE8888 mode flexibility
2020-04-23 16:57:37 -04:00
d3745c0f9e
smart gpio clean-up
2020-04-06 14:13:29 -04:00
2efa22f926
code style
2020-04-06 12:34:21 -04:00
ba9424f538
clean-up by Dron0Gus
2020-04-06 11:55:44 -04:00
a47dce4025
code style
2020-04-01 21:32:21 -04:00
8c38bd5ad1
verboseTLE8888
2020-02-27 02:11:20 -05:00
333a7a6608
TLE8888 watchdog #917
2020-02-12 19:32:40 -05:00
deb73f505b
#917 progress
2020-02-12 17:37:45 -05:00
efc8d69085
and fixing build now!
2020-02-12 17:23:22 -05:00
6c843e6954
tle8888 refactoring already - extracting method
2020-02-12 17:19:58 -05:00
3b61334714
tle8888: disable diagnostic for outputs ( #1144 )
...
DS is not clear, may be tle8888 clears OE bit in case of error on
output.
2020-02-12 08:53:35 -05:00
74ead04e84
tle8888 dump at init
2020-02-12 08:34:26 -05:00
86b3332cfe
have nothing else to do :(
2020-02-12 08:24:24 -05:00
4dbff5ff30
tle8888 output fix
2020-02-12 08:15:55 -05:00
2eec13007e
FATAL error running MRE blinking test #1137
...
typo
2020-02-11 17:52:01 -05:00
1e010c8e82
Merge branch 'master' of https://github.com/rusefi/rusefi
2020-02-11 17:49:49 -05:00
8c1536dd0e
FATAL error running MRE blinking test #1137
...
still not the fix?
2020-02-11 17:49:39 -05:00
82e33e45af
Tle8888 wd ( #1143 )
...
* tle8888: watchdog: debug over TS: remove tailing register address
* tle8888: ann console command to dump all regs
2020-02-11 17:49:14 -05:00
678c3525b8
tle8888: watchdog: debug using TS ( #1142 )
2020-02-11 16:56:52 -05:00
95ce978c23
tle8888: watchdog: use FWDRespSyncCmd for last response ( #1140 )
2020-02-11 15:49:17 -05:00
7bd68beae9
tle8888: watchdog: do not overwrite defaults, response table fix ( #1139 )
2020-02-11 15:36:53 -05:00
6b874c12c0
TLE8888 watchdog #917
...
still no luck. responses 0x85c and 0xa5c
2020-02-11 00:54:15 -05:00
cd9c291e3e
WdDiag
2020-02-10 21:28:55 -05:00
41253b88b8
TLE8888 watchdog #917
...
time to start working?!
2020-02-10 18:32:32 -05:00
a29d6fc241
TLE8888 watchdog #917
...
maybe better start-up sequence
2020-02-10 17:08:37 -05:00
0b8c1e69dc
TLE8888 watchdog #917
2020-02-10 14:37:52 -05:00
59eb424ba0
TLE8888 watchdog #917
...
window watchdog progress
2020-02-10 13:24:09 -05:00
b3bc3325b9
TLE8888 watchdog #917
...
first steps
2020-02-10 11:11:00 -05:00
cb8612a15c
code style
2020-02-10 09:29:11 -05:00
551273a336
FATAL error running MRE blinking test fix #1137
2020-02-09 21:16:31 -05:00
51cfc6bcf1
tle8888 start-up clean-up
2020-02-09 20:41:25 -05:00
8a88c90f3b
code style: trying to get used to this syntax
2020-01-22 00:45:09 -05:00
bb217b01dd
happy new year unification
2020-01-13 21:57:43 -05:00
618d6f5a5e
Gpio diagnostic ( #1100 )
...
* enums: add brain_pin_diag_e enum for pin diagnostic
* gpio core: add pin diagnostic call
* gpio: mc33810: add diagnostic support
* gpio: mc33972: add diagnostic support
* gpio: tle6240: add diagnostic
* pin_repository: output diagnostic data for gpio chips
* enums: kinetis: add brain_pin_diag_e enum for pin diagnostic
2020-01-12 10:20:10 -05:00
85a460f2ba
hw: gpio: use unsigned int as pin number inside gpiochip drives ( #1097 )
...
Not brain_pin_e. Drivers like to see pin number within current
chip.
2020-01-11 10:29:41 -05:00
b83a5310be
happy new year
2020-01-08 00:02:40 -05:00
9f0d84f338
Gpio fixes ( #1086 )
...
* drivers: gpio: add MC33810 driver (skeleton)
* pin_repository: debug: do not show absent chips
2020-01-07 07:55:50 -05:00
9645130527
Shrink output channels, now with passing CI ( #1077 )
...
* reorder fields
* temporary tle8888 fix
* comment, simplify
* hand tweak generated
* oops, those are reciprocal
* fix engineLoadAccelExtra
* aggressive priority order
* fix output size
* comments
* reorder fields, no sizes yet
* should've been signed
* simplify constructor mess, hook up scaling
* notes
* typo
* if -> switch
* rev signature
* correct map offset
* handle unsigned properly
* RPM is unsigned
* vss isn't scaled
* extract magic
* required generated for build
* de-scale rpm
* field type cases
2019-12-22 08:12:45 -05:00
871f86967f
Revert "DRAFT Shrink output channels, again ( #1074 )"
...
This reverts commit 562ce6cc
2019-12-21 15:02:49 -05:00
562ce6ccaf
DRAFT Shrink output channels, again ( #1074 )
...
* reorder fields
* temporary tle8888 fix
* comment, simplify
* hand tweak generated
* oops, those are reciprocal
* fix engineLoadAccelExtra
* aggressive priority order
* fix output size
* comments
* reorder fields, no sizes yet
* should've been signed
* simplify constructor mess, hook up scaling
* notes
* typo
* if -> switch
2019-12-21 08:55:19 -05:00
22f2739764
Revert "Shrink output channels, use scaling ( #1069 )"
...
This reverts commit 89405014
2019-12-19 22:35:06 -05:00
89405014cf
Shrink output channels, use scaling ( #1069 )
...
* reorder fields
* temporary tle8888 fix
* comment, simplify
* hand tweak generated
* oops, those are reciprocal
* fix engineLoadAccelExtra
* aggressive priority order
2019-12-19 20:37:42 -05:00
7dfdfc6378
docs & code formatting
2019-11-19 18:17:03 -05:00
63702dbeeb
TLE6240 outputs fix ( #994 )
2019-11-01 15:49:55 -04:00
ee5ee1942c
Kinetis & TLE8888 compatibility & fixes... ( #991 )
...
* TLE8888: More compatibility & postTunerStudioState
* activeConfiguration & EFI_ACTIVE_CONFIGURATION_IN_FLASH fix
* Kinetis: jump_to_bootloader() impl.
* Kinetis: UART baudrate safety check
* Kinetis: OMG!..
2019-10-31 16:06:34 -04:00
29804cbc8a
move tsOutputChannels to header ( #970 )
2019-10-08 21:02:51 -04:00
5d8e1f6c73
tle8888 reinit command
2019-09-05 10:30:27 -04:00
e4566ba6aa
TLE8888: NB2 solution + reset counter
2019-09-05 10:01:59 -04:00
51db88de18
TLE8888: track reset event by cleared OE bit in status register ( #918 )
...
As tle8888 suposed to be reset master and reset MCU there is no
flag showing POR reset. So try to poll OE bit.
2019-09-05 08:55:17 -04:00
c9241b89da
Hall mode for TLE88888 - VRSConfig1 VRSM #915
2019-09-04 20:02:32 -04:00
6262a5e84e
Hall mode for TLE88888 - VRSConfig1 VRSM #915
2019-09-04 09:24:01 -04:00
07cc3cffff
Hall mode for TLE88888 - VRSConfig1 VRSM #915
2019-09-04 00:27:19 -04:00
b09ab8a57f
TLE8888 should be re-initialized every time we get +12 volts fix #901
...
fuel pump test passed, also longer start-up timeout is needed for reliable start
2019-08-16 23:21:03 -04:00
51902c12c5
TLE8888 should be re-initialized every time we get +12 volts #901
...
moving SPI initialization to thread - still works on real hardware
2019-08-16 22:56:06 -04:00
7eb3c7122f
TLE8888 should be re-initialized every time we get +12 volts #901
...
refactoring: extracting method
2019-08-16 22:41:19 -04:00
ed854a3828
refactoring
2019-08-16 22:01:32 -04:00
9d32f2c40a
refactoring: ChibiOS now offers native 'lockAnyContext' pattern
2019-08-11 15:23:15 -04:00
ee41d37c08
code style/type safety/docs/typos
2019-08-10 11:13:41 -04:00
c29a6bb323
MRE hangs up on bench fix #899
2019-08-10 00:53:16 -04:00
cdac02429c
refactoring: better file name
2019-07-06 20:15:49 -04:00
7280d65cf8
we need TLE8888 driver #714
2019-06-08 21:58:23 -04:00
787af95050
tle8888 driver bug #803
...
undoing since this breaks start-up
2019-06-08 20:28:13 -04:00
d6be89d9b0
we need TLE8888 driver #714
...
trying a sleep before first command
2019-06-08 18:31:56 -04:00
bd4c5a017e
we need TLE8888 driver #714
...
saving exact TLE8888 reponses
2019-06-08 16:13:24 -04:00
061e7c6bf0
https://github.com/rusefi/rusefi/issues/803
2019-06-08 00:44:18 -04:00
0fb89c4f7b
better status code
2019-06-07 19:14:55 -04:00
7dff7a08c9
reviving tle8888 configuration
2019-06-05 22:32:30 -04:00
c7c613a7fa
code style
2019-06-05 21:44:58 -04:00
0b5572d229
docs
2019-05-30 17:43:40 -04:00
04ee37548b
Smart gpios fixes 3 ( #795 )
...
* pin_repository: provide readable pin names in error cases
* io_pins: remove getBrain_pin_eExt
We have getBrain_pin_eExt in io_pins.cpp and hwPortname in
pin_repository.cpp.
First uses auto-generated enums, second one uses runtime data to
provide name of hw pin.
Removing first saves us about 2K of flash couse big auto-generated
switch with pin names no more used by anyone and gets optimized out.
* gpios: mc33972: CS pin is now requested at smart_gpios.pcc
* getSpiDevice: support SPI4
* smart_gpios.cpp: startSmartCsPins set CSs to inactive state
OutputPin:initPin initializes pin with false value. This is active
state for SPI Chip Selects. Set to 1 to deselect all chips.
2019-05-09 18:09:24 -04:00
b80d95578d
EFI_CONSOLE_UART_DEVICE, flash->hw_ports, Fix TLE6240 and misc.fixes ( #793 )
...
* rename EFI_CONSOLE_UART_DEVICE -> EFI_CONSOLE_SERIAL_DEVICE
* Impl. EFI_CONSOLE_UART_DEVICE
* Move flash source files to ports/stm32/ & hw_ports.mk
* Fix TLE6240
* Fix EFI_NO_CONFIG_WORKING_COPY
* EFI_PRINT_MESSAGES_TO_TERMINAL
2019-05-05 11:06:27 -04:00
ba118e61f2
tle8888: fix pin names array ( #771 )
2019-04-21 08:50:07 -04:00
f62731cc99
USB and TLE8888 not working for F4 or F767 #764
2019-04-20 23:39:06 -04:00
71cc657f10
Smart gpio fixes 2 ( #765 )
...
* gpio chips: relax error checking on _add
Do not halt whole system if wrong or nulled config is passed.
In current smart-gpio implementation this can happen and it is not
as error. Let smart-gpio handle this, kust reurn negative.
* tle8888: return back includes needed for debug
* smar-gpio: -Werror=missing-field-initializers fix
2019-04-19 01:42:24 -04:00
Andrey G
Matthew Kennedy
rusefi
rusEfi
andreika-git