a57d315e4b
http://code.google.com/p/arduino/issues/detail?id=368
...
Optiboot does not support ArduinoasISP programmer.
When avrdude runs and talks to an arduino running ArduinoISP,
it needs the optiboot (entered due to auto-reset) to abort and
start the ArduinoISP "application" when it sees communications
at the wrong serial speed. Unfortunately, optiboot treats all
unrecognized command characters as "no-ops" and responds/loops
for more commands, leading to a nice loop that never gets to
the sketch. This patch causes characters received with Framing
errors (the most likely error for speed mis-matches) to NOT
reset the watchdog timer (normally done in getch()), which will
cause the application to start if it continues for "a while."
(tested. Works! Running ArduinoISP at speeds as high as 57600
still causes the bootloader to start the sketch (although it fails
later on for other reasons.))
(cherry picked from commit e81c1123b6
2011-10-10 12:11:16 -04:00
1bbded4f34
(make sure .hex and .lst are updated as well.)
...
(cherry picked from commit ece29c3805
2011-10-10 12:11:16 -04:00
091dc9a7f9
Fix errors in LDSECTIONS refactoring
...
(found during atmega8 testing.)
(cherry picked from commit 422398e08c
2011-10-10 12:11:16 -04:00
93f7515ecf
Update version to reflect previous edit. Sigh.
...
(cherry picked from commit e28b716f88
2011-10-10 12:11:15 -04:00
07a88dc998
Shrink code by using registers for variables "length" and "address"
...
http://code.google.com/p/optiboot/issues/detail?id=33
Fix high-value watchdog timeouts on ATmega8
http://code.google.com/p/optiboot/issues/detail?id=38
Change "start app on bad commands" code to start the app via the
watchdog timer, so that the app is always started with the chip
in fully reset state.
http://code.google.com/p/optiboot/issues/detail?id=37
(cherry picked from commit 6f7687b0f9
2011-10-10 12:11:15 -04:00
10019bb0df
Add a version number to the optiboot source and binary.
...
http://code.google.com/p/arduino/issues/detail?id=554
end of flash memory where they can be read (at least in theory) by
device programmers, hex-file examination, or application programs.
This is done by putting the version number in a separate section
(".version"), and using linker/objcopy magic to locate that section as
appropriate for the target chip. (See
http://lists.gnu.org/archive/html/avr-gcc-list/2011-02/msg00016.html
for some discussion on the details.)
Start the version at 4.1 (the last "packaged" version of optiboot was
called version 3, so the "top of source" would be 4.0, and adding the
version number makes 4.1)
Refactor LDSECTION in the Makefile to LDSECTIONS so that multiple
section start addresses can be defined.
Change the _isp makefile definitions to make the bootloader section
readable (but not writable) by the application section. (This would
need to be done elsewhere as well to handle all bootloader programming
techniques. Notably Arduino's boards.txt
Note that this change does not change the "code" portion of optiboot
at all. The only diffs in the .hex files are the added version word
at the end of flash memory.
(cherry picked from commit 00706284de
2011-10-10 12:11:15 -04:00
287aae6b42
Update shell script makeall
...
(cherry picked from commit d4632cb095
2011-10-10 12:11:14 -04:00
92e746d0a5
This is a relatively significant edit that brings the Arduino copy of
...
optiboot up-to-date with the optiboot source repository as of Jun-2011
(the last changes made in the optiboot repository were in Oct-2010)
This adds support for several plaforms, fixes the "30k bug", and
refactors the source to have separate stk500.h, boot.h, and pin_defs.h
These are the arduino opticode issues fixed:
http://code.google.com/p/arduino/issues/detail?id=380
optiboot has problems upload sketches bigger than 30 KB
http://code.google.com/p/arduino/issues/detail?id=556
update optiboot to the point of the latest optiboot project sources.
These are issues that had been solved in the optiboot source aready:
http://code.google.com/p/arduino/issues/detail?id=364
optiboot leaves timer1 configured when starting app, breaks PWM on
pin 9 and 10. (fixed with a workaround in arduino core.)
aka http://code.google.com/p/optiboot/source/detail?r=c778fbe72df6ac13ef730c25283358c3c970f73e
Support for ATmega8 and mega88.
Fix fuse settings for mega168 _ISP targets
Additional new platforms (mega, sanguino)
http://code.google.com/p/optiboot/issues/detail?id=26
Set R1 to 0 (already in arduino code)
http://code.google.com/p/optiboot/issues/detail?id=36&can=1
Fails to build correctly for mega88
After this commit, the only differences between the Arduino optiboot.c
and the optiboot repository optiboot.c are cosmetic.
(cherry picked from commit e2812ef91c
2011-10-10 12:11:14 -04:00
72e425a41d
http://code.google.com/p/arduino/issues/detail?id=517
...
Remove the trailing comments when setting fuse values for the various
*_isp targets, so that they won't cause avrdude errors.
This was done the same way as in the optiboot source tree:
http://code.google.com/p/optiboot/issues/detail?id=17
http://code.google.com/p/optiboot/source/detail?r=005fb033fc08c551b2f86f7c90c5db21549b3f20
(cherry picked from commit 6840b77643
2011-10-10 12:11:14 -04:00
11b2d86ff1
Makefile modification to allow building optiboot in more environments.
...
Allows building within the Arduino Source tree, and within the Arduino
IDE tree, as well as using CrossPack on Mac.
Adds README.TXT to track arduino-specific changes (and documents the
new build options.)
This addresses Arduino issue:
http://code.google.com/p/arduino/issues/detail?id=487
And optiboot issue
http://code.google.com/p/optiboot/issues/detail?id=1
(which can be thought of as a subset of the Arduno issue.)
Note that the binaries produced after these Makefile changes (using any
of the compile environments) are identical to those produced by the
crosspack-20100115 environment on a Mac.
(cherry picked from commit 2d2ed324b4
2011-10-10 12:11:13 -04:00
f093cc6970
Merge pull request #30 from WestfW/master
...
Significant optiboot upgrade.
2011-10-10 09:01:56 -07:00
a08657b350
Moving USBasp in programmers menu.
2011-10-10 11:58:38 -04:00
2ffad50619
Merge pull request #41 from chiva/patch-1
...
Added USBasp to programmers list
2011-10-10 08:56:15 -07:00
ca671fdc05
Fixing more warnings (Paul Stoffregen).
2011-10-10 11:28:44 -04:00
fc8cacb9a3
Explicitly set the SHELL variable when OS=windows, so that we'll use
...
the same shell regardless of whether other shells are installed
(different shells have different behavior WRT directory component
separators, so this matters.
http://code.google.com/p/arduino/issues/detail?id=667 )
2011-10-05 01:41:03 -07:00
85c109f255
Fixing warnings in Stream (Paul Stoffregen)
...
http://code.google.com/p/arduino/issues/detail?id=208
2011-10-02 09:44:21 -04:00
6554ae653c
Using alternate timer 0 overflow interrupt signal name for ATtiny24/44/84.
2011-09-30 11:24:44 -04:00
bd823bf201
Changing Ethernet upload protocol from stk500 to arduino.
...
http://code.google.com/p/arduino/issues/detail?id=649
2011-09-28 23:26:37 -04:00
de22990133
Updating bootloader comments.
2011-09-16 20:31:41 -04:00
df2270d4d5
Commenting out micro board for now since it's not being released yet.
2011-09-16 20:26:43 -04:00
19d7d4b066
Updating Micro bootloader (previous one was identical to Leonardo).
2011-09-16 18:25:59 -04:00
d532d85059
added Mouse.isPressed() method
2011-09-16 16:59:14 -04:00
00c3631467
made some Keyboard methods private
2011-09-16 16:43:07 -04:00
30fc9919e1
added support for TIMER4D used for PWM on Leonardo and Micro D6
2011-09-16 16:36:42 -04:00
b898a35f76
new bootloader binaries for Micro and Leonardo - uses new assignment for TXLED pin
2011-09-16 16:24:21 -04:00
a4ccf47ec7
updated pin assignment again based on design files for Leonardo
2011-09-16 16:12:39 -04:00
23d0d05844
updated pin mappings for bootloader and pins_arduino.h in anticipation of final hardware.
2011-09-16 15:46:51 -04:00
8638d5b4e9
restored accidentally-deleted Leonardo type in boards.txt
2011-09-16 14:54:42 -04:00
75cfefcd0a
restored Micro entry in boards.txt, made separate bootloader images for Leonardo and Micro.
2011-09-16 14:47:42 -04:00
cd5ecfff1c
Merge https://github.com/arduino/32U4 into new-extension
2011-09-16 14:34:55 -04:00
667da698d7
added automatic one-shot TX and RX LED control for sketch USB
2011-09-16 14:32:25 -04:00
5ec35fc68c
Moving Leonardo after Uno.
2011-09-16 14:24:11 -04:00
6b7d24edb0
added to sketch iProduct and iManufacturer strings identifying board as either an "Arduino Leonardo" or "Arduino Micro" manufactured by "Arduino LLC"
2011-09-16 12:29:47 -04:00
4452de6eaa
bootloader iProduct definition changed to "Arduino Leonardo Bootloader" or "Arduino Micro Bootloader". selection depends on PID passed in at compile time
2011-09-16 12:09:51 -04:00
66b484e53e
added to the bootloader iProduct and iManufacturer strings identifying board as an "Arduino Leonardo" manufactured by "Arduino LLC"
2011-09-16 11:56:33 -04:00
6bbc7b2db7
faster LED breathing animation in bootloader
2011-09-16 11:18:39 -04:00
ab8fc5aab7
Merge branch 'new-extension' of https://github.com/arduino/Arduino into new-extension
2011-09-16 10:27:11 -04:00
90f285ae9c
Added USBasp to programmers list
2011-09-16 01:56:22 +03:00
d4e9db463b
fixed analog pin mapping for 32u4
2011-09-13 23:52:26 -04:00
18d76057fe
fixed Mouse button assignments
2011-09-13 21:37:46 -04:00
e3fa1ed039
made Mouse.buttons() private. removed MOUSE_ALL macro
2011-09-12 08:14:13 -04:00
f3d8628c5e
Don't consume trailing char in parseInt() and parseFloat (Paul Stoffregen).
...
http://code.google.com/p/arduino/issues/detail?id=624
2011-09-09 16:24:47 -04:00
6f65578b99
updated Leonardo INF with correct PID and created new Micro INF.
2011-09-08 20:45:10 -04:00
b1c8d0be34
in bootloader reduced delay between receiving stk500 'Q' and jumping to application
2011-09-08 20:38:23 -04:00
94879d3ac6
Merge branch 'new-extension' of https://github.com/arduino/Arduino into new-extension
...
Conflicts:
build/linux/dist/tools/avrdude.conf
2011-09-08 20:26:47 -04:00
db7013f95c
fixed bug where sketches over 28k caused subsequent auto-reset-and-upload attempts to fail. fixed bug in reboot routine, changed fuses to select 1024-word bootloader size, disabled hardware boot enable.
2011-09-08 19:31:18 -04:00
c0b45364b8
disabling watchdog in bootloader
2011-09-08 18:12:11 -04:00
11e3921c81
misc. bootloader fixes: increased wait time after receiving avrdude 'Q', increased bootloader timeout, and fixed LED one-shot timing
2011-09-08 16:23:29 -04:00
e870f070db
added compile-time definition of sketch PID. PID is pulled from variants/leonardo or the new variants/micro as appropriate.
2011-09-08 15:52:05 -04:00
508eb9b72f
removed leftover pins/ directory
2011-09-08 15:43:16 -04:00
301f1b8552
Revert "added Micro section to boards.txt. specified different bootloader hex files for Leonardo and Micro (differ only by PID). added PID entries to boards.txt"
...
This reverts commit 3b5122e138
2011-09-08 15:40:41 -04:00
c295917fad
Revert "support compile-time passing of PID to Leonardo/Micro sketches. PID comes from boards.txt - different for Micro and Leonardo"
...
This reverts commit 3e0d195492
2011-09-08 15:39:17 -04:00
3e0d195492
support compile-time passing of PID to Leonardo/Micro sketches. PID comes from boards.txt - different for Micro and Leonardo
2011-09-08 11:23:55 -04:00
3b5122e138
added Micro section to boards.txt. specified different bootloader hex files for Leonardo and Micro (differ only by PID). added PID entries to boards.txt
2011-09-08 11:00:40 -04:00
48212b11fd
changed PIDs for Leonardo and Micro. PIDs are now defined in the Makefile
2011-09-08 09:47:17 -04:00
4db174e67b
removed all bootloader mass storage and MSC references
2011-09-08 09:12:30 -04:00
7d8d20894c
Making Print::write(char *) non-virtual.
...
http://code.google.com/p/arduino/issues/detail?id=607
2011-09-07 18:41:05 -04:00
ab36bd5dbb
Changing to a simpler mental model for serialEvent (Paul Stoffregen).
...
http://code.google.com/p/arduino/issues/detail?id=626
2011-09-07 17:47:17 -04:00
fa901e2ba4
changed auto-reset trigger condition to fix auto-reset-and-upload for Windows. now reboots when a port, opened at 1200 bps, is closed.
2011-09-06 20:58:00 -04:00
5e058a8aa3
changed baudrate for auto-reset-and-upload back to 1200 bps. specified arduino protocol for Leonardo avrdude upload.
2011-09-05 13:08:05 -04:00
e24e9499cf
Merge branch 'new-extension' of https://github.com/arduino/Arduino into new-extension
...
Conflicts:
build/macosx/dist/tools-universal.zip
build/windows/avr_tools.zip
hardware/arduino/cores/arduino/HardwareSerial.cpp
2011-09-05 12:53:45 -04:00
83da177280
Merge branch 'new-extension' of github.com:arduino/Arduino into new-extension
2011-09-02 19:58:39 -04:00
85bf4252f0
Updating to avrdude 5.11 (Windows). stk500 -> arduino in boards.txt.
...
http://code.google.com/p/arduino/issues/detail?id=606
2011-09-02 19:57:29 -04:00
bf5e928e4c
Adding Arduino Ethernet and Arduino Mega ADK (joint w/ Mega 2560) to boards menu.
...
http://code.google.com/p/arduino/issues/detail?id=594
2011-08-31 16:48:06 -04:00
1278144d50
Moving serialEvent() calls from RX interrupts to main for() loop (after loop()).
...
http://code.google.com/p/arduino/issues/detail?id=584
2011-08-31 15:52:56 -04:00
61b33f11ce
Renaming writeError() to getWriteError() in Print (and Stream and friends).
...
http://code.google.com/p/arduino/issues/detail?id=608
2011-08-31 15:39:20 -04:00
3389d28e20
added Mouse press() and release()
2011-08-30 20:23:06 -04:00
7d26163b16
on a CDC or HID write() error, call setWriteError(). better handling of USB_Send errors in CDC.
2011-08-30 17:25:35 -04:00
a6093a8d91
Created an abstract base class UDP to match the Client and Server classes, and reworked the Ethernet library to use it and derive EthernetUDP.
2011-08-30 21:27:31 +01:00
6049e4455a
support for non-Leonardo boards is back!
2011-08-30 11:50:08 -04:00
0b3acaea21
CDC and HID write() routines now return non-void - brought in line with new write behavior
2011-08-30 11:04:34 -04:00
0a34c0f35e
brought leonardo folder in line with new variants scheme
2011-08-30 10:45:41 -04:00
91f89da73a
Merge branch 'mainline' into new-extension
2011-08-30 08:38:06 -04:00
ad5dead85a
Changed names of the Ethernet classes: Client -> EthernetClient, NetClient -> Client, and basic testing performed
2011-08-29 22:36:28 +01:00
b7533c1839
Final changes to integrate latest core updates to WiFly branch
2011-08-28 22:26:07 +01:00
e1748e79d7
Merge branch 'master' into wifly_integration
2011-08-28 20:28:53 +01:00
6345e2942a
auto-upload-and-reset works now at 300 bps. patched avrdude for Mac to support 300 bps connection, changed core and boards.txt to match
2011-08-27 20:32:34 -04:00
4588120106
Merge branch 'new-extension' of https://github.com/arduino/Arduino
2011-08-27 23:53:42 +01:00
bef7d736d2
bootloader ends as soon as sketch upload finishes. restored pulsing of LED while bootloader running.
2011-08-27 07:00:07 -04:00
b73cf39d94
Moving write errors out of return value into separate API methods.
...
write(), print(), println() now return size_t (and don't use negative values to signal errors).
Print adds writeError() for checking for write errors, clearWriteError() to reset the flag to false, and a protected setWriteError() for signalling errors.
http://code.google.com/p/arduino/issues/detail?id=598
2011-08-26 16:08:14 -04:00
929597375b
Changing from long to ssize_t (int) for write(), print(), println() return.
2011-08-26 14:20:41 -04:00
eebe997dce
bugfix - Serial.write() would try to send even if no CDC connection was open.
2011-08-24 21:04:30 -04:00
ff5fe87864
changed auto-reset method for upload: now triggered by opening port at 1200 bps
2011-08-24 17:12:28 -04:00
8059abe581
write(), print(), and println() now return number of bytes written.
...
The type is long, and negative values indicate errors. Needs more testing.
http://code.google.com/p/arduino/issues/detail?id=551
2011-08-23 19:12:03 -04:00
b788ad593f
Distinguishing those boards with eight analog inputs (Fio, BT, Nano, Mini).
...
http://code.google.com/p/arduino/issues/detail?id=499
2011-08-23 17:29:20 -04:00
d00f0949ed
Renaming pins/ directory to the more generic variants/
...
http://code.google.com/p/arduino/issues/detail?id=588
2011-08-23 17:07:39 -04:00
dd539bacf8
USB microcontrollers will call USB.attach() after init(), before setup()
2011-08-18 19:59:35 -04:00
5b989d13b3
HW Serial on pins 0 and 1 works. Accessed by Serial1.* methods
2011-08-18 19:40:04 -04:00
4b0a87b405
Stream.readBytesUntil() now writes null terminator within length.
2011-08-18 15:13:47 -04:00
cb39ad9739
A few API changes to new Stream parsing functions.
...
Renamed readChars() -> readBytes(), readCharsUntil() -> readBytesUntil().
Changed timeouts to milliseconds from seconds; default from 5 to 1 seconds.
Removed readCharsBetween().
2011-08-17 14:16:47 -04:00
682b58e577
Integrating Stream searching & parsing (Michael Margolis)
...
This from Michael's TextFinder library, incorporated into the Stream class: find(), findUntil(), parseInt(), parseFloat(), readChars(), readCharsUntil(), readCharsBetween(), setTimeout().
2011-08-17 13:53:49 -04:00
e3848670a7
Temporary fix for auto-reset from IDE. Will reset chip when DTR is asserted, no matter what CDC baud rate is selected.
2011-08-16 13:43:55 -04:00
3f6df054ee
Serial via USB works
...
Integrated rest of Peter's USB implementation
2011-08-14 16:59:34 -04:00
e254d2989d
LEDs for D13, TX, and RX are more in line with Uno-like behavior during sketch uploading.
...
D13 flashes on reboot, TX and RX flash with USB data transfer.
2011-08-14 16:02:16 -04:00
c149be22f7
rebuilt Diskloader, added LED control macros for Leonardo, removed Microtouch defines
2011-08-14 15:11:23 -04:00
13a269df2e
increased bootloader delay to approx. 3.5 s
2011-08-14 14:29:44 -04:00
d338f22bde
Adding basic macros for analog + digital pin information.
...
http://code.google.com/p/arduino/issues/detail?id=495
2011-08-12 18:27:00 -04:00
f179794a45
Adding pin-change interrupt pin mapping macros to pins_arduino.h.
...
http://code.google.com/p/arduino/issues/detail?id=490
2011-08-12 17:31:22 -04:00
f14fd94d0e
Adding SCL, SDA, and LED #defines.
2011-08-12 16:59:24 -04:00
213091f487
cleaned up types. set D5 as not a PWM pin for now.
2011-08-11 14:16:13 -04:00
WestfW
David A. Mellis
Zach Eveland
Santiago Reig
amcewen