2014-09-15 15:40:17 -07:00
|
|
|
# Board - Naze32
|
|
|
|
|
|
|
|
The Naze32 target supports all Naze hardware revisions. Revison 4 and Revision 5 are used and
|
|
|
|
frequently flown by the primary maintainer. Previous Naze hardware revisions may have issues,
|
2014-11-14 04:44:17 -08:00
|
|
|
if found please report via the [github issue tracker](https://github.com/cleanflight/cleanflight/issues).
|
2014-09-15 15:40:17 -07:00
|
|
|
|
|
|
|
# Serial Ports
|
|
|
|
|
2014-10-18 08:40:21 -07:00
|
|
|
| Value | Identifier | RX | TX | Notes |
|
|
|
|
| ----- | ------------ | --------- | ------------------ | ------------------------------------------------------------------------------------------- |
|
2014-11-23 05:17:42 -08:00
|
|
|
| 1 | USART1 | RX / PA10 | TX / PA9 / TELEM | TELEM output is always inverted (for FrSky). Internally connected to USB port via CP2102 IC |
|
|
|
|
| 2 | USART2 | RC4 / PA3 | RC3 / PA2 | |
|
2014-10-18 08:40:21 -07:00
|
|
|
| 3 | SoftSerial 1 | RC5 / PA6 | RC6 / PA7 | |
|
|
|
|
| 4 | SoftSerial 2 | RC7 / PB0 | RC8 / PB1 | |
|
|
|
|
|
|
|
|
* You cannot use USART1/TX/TX/TELEM pins at the same time.
|
|
|
|
* You may encounter flashing problems if you have something connected to the RX/TX pins. Try disconnecting RX/TX.
|
2014-09-15 15:40:17 -07:00
|
|
|
|
2014-11-30 15:37:03 -08:00
|
|
|
# Pinouts
|
|
|
|
|
|
|
|
The 10 pin Input connector has the following pinouts when used in RX_PPM/RX_SERIAL mode
|
|
|
|
|
|
|
|
| Pin | Identifier | Function | Notes |
|
|
|
|
| --- | ---------- | -------------- | -------------------------------- |
|
|
|
|
| 1 | N/A | Ground | |
|
|
|
|
| 2 | Circle | +5V | |
|
|
|
|
| 3 | 1 | PPM Input | Enable `feature RX_PPM` |
|
|
|
|
| 4 | 2 | RSSI_ADC | Enable `feature RSSI_ADC`. Connect to the output of a PWM-RSSI conditioner, 0v-3.3v input |
|
|
|
|
| 5 | 3 | Uart 2 TX | |
|
|
|
|
| 6 | 3 | Uart 2 RX | |
|
|
|
|
| 7 | 5 | Softserial1 TX | Enable `feature SOFTSERIAL` |
|
|
|
|
| | | Led Strip | Enable `feature LED_STRIP`. |
|
|
|
|
| 8 | 6 | Softserial1 RX | Enable `feature SOFTSERIAL` |
|
|
|
|
| 9 | 7 | Softserial2 TX | Enable `feature SOFTSERIAL` |
|
|
|
|
| 10 | 8 | Softserial2 RX | Enable `feature SOFTSERIAL` |
|
|
|
|
| | | Current | Enable `feature CURRENT_METER`. Connect to the output of a current sensor, 0v-3.3v input |
|
|
|
|
|
|
|
|
|