PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
status in cli now prints cpu MHz, 72 when running off crystal, 64 when running off intrc.
corrected WHO_AM_I check for mpu6050 when it's used on alternate address (AD0 high).
corrected PWM driver to consider CPU clock for timer prescalers - now things properly work below 72MHz
added a neat hack for pitch angle calculation so that it's not affected when roll reaches 90deg
added proper math for vector rotation instead of small-angle approximation
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@225 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added a modifier for set (type "set *") to see min/max values for each parameter. this is for gui stuff
bumped config VERSION
fixed 0xffff - now stuff in drv_pwm, after it was mentioned to me for the 3rd time :p
replaced some uint8_t -> uint32_t for loop counters - saving 4 to 8 bytes of flash each time. thanks goes to thee 35+ years of C experience kicad guy.
turned bitfiends into a regular struct - instant 100byte flash size reduction
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@174 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
put gyro interleave under define. this needs to be cleaned sometime.
took out "gyro glitch" stuff that was leftover from nintendo days.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@162 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
increased i2c send buffer to 16bytes (was needed for DMP)
decreased interrupt priority of both uarts - with GPS running at 115200, this would cause I2C errors (i2c interrupt must be highest priority).
GPS was tested with $25 FMP04 GPS module ghettoed up outside my window, locking 5 satellites in a few minutes.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@140 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
removed feature digital_servo since its now set by cli instead.
added proper tx end check into uart, to remove delay inside printing out set values and tx buffer overrun during help()
instead of passing a bunch of params to pwm driver, made a config struct
fixed a bug in gps baudrate
fixed typo in stmloader.c
whitespace / indentation cleanups in various drivers
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@137 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added (untested) support for additional PWM output channels incase of PPM input - 4 more, so total of 10 outputs in this mode.
added (mostly untested) support for throttle calibration - short out PPM input connector with a bind plug and power up.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@122 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
timecop@gmail.com
dominicc1974@gmail.com
timecop