Mitch Lustig
15703429f5
Add gyro tuning functionality & state machine logic
2019-08-04 11:47:23 -07:00
Mitch Lustig
800115f683
Implement more data to help debug
2019-07-30 00:27:23 -07:00
Mitch Lustig
bbba718140
Work to get GUI going
2019-07-29 00:31:48 -07:00
Mitch Lustig
fccb59b2ef
Merge branch 'master' into balance
2019-07-27 21:28:02 -07:00
Mitch Lustig
271dd21dab
start in balanace app
2019-07-27 21:25:56 -07:00
Davide D'Agostino
19fb5e04c6
Rebuild the firmwares
2019-06-29 19:59:02 -07:00
Davide D'Agostino
ce802e3547
Move the new smart revers funcion as separate control type
...
Removed unnecessary ADC fields from its config.
2019-06-24 13:36:55 -07:00
Davide D'Agostino
05b0f0dd9f
Port Ackmaniac smart reverse
2019-06-19 19:00:46 -07:00
Benjamin Vedder
a141e750bb
Added CAN status msg 5, fixed issue 94, use defaul HW parameters after autodetect
2019-05-16 23:30:40 +02:00
Marcos Chaparro
6d758b38f2
Detect current sensor failures
...
2 failure modes added:
* On boot, when calculating DC offsets generate a fault if the offset is beyond
HW_MAX_CURRENT_OFFSET. Fault code reports which sensor is having issues (1, 2 or 3).
Most likely cause is a disconnected sensor, if hw has fault-detecting pullups.
* On runtime, in setups with 3 in-line phase current sensors, checks that the sum
of the currents is below MCCONF_MAX_CURRENT_UNBALANCE, with a configurable low pass
filter. If unbalanced current is high, it means a fault to ground, or a disconnected
sensor (this works at 0 Amp if hw has pullups in the sensor input to detect the
failure).
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-20 09:43:08 -03:00
Benjamin Vedder
4a9fe93f41
Added support for storing hw-specific and custom variables in EEPROM
2019-04-19 10:42:43 +02:00
Marcos Chaparro
1ae059349f
CRC integrity check of flash memory
...
The check only covers address 0x08008000 to 0x805FFFF, where application
code is stored. It excludes virtual eeprom area (first 0x8000 bytes)
because it is modified on runtime with user configurations.
After a fresh flash programming the CRC is read as 0xFFFFFFFF and firmware
computes and stores the new CRC and a reset is invoked.
After reset the CRC will be available for checking code integrity.
Linker file had a wrong flash2 size, it was set to 480kB, thus allowing
the linking of binaries larger than 393216 (x3 128kB sectors).
The bootloader won't program binaries that span more than 3 sectors.
Now flash2 length is set as (393216 - 8) to ensure that the last 8 bytes
are left blank (0xFFFF) and reserved for CRC information.
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-15 20:56:42 -03:00
Benjamin Vedder
025334c141
Merge pull request #85 from tipsmiller/master
...
Add new control type to ADC application
2019-04-14 07:22:56 +02:00
Marcos Chaparro
d80227b9b4
Rename sin/cos m_conf structure fields
...
Use m_foc prefix so in VESC Tool they are edited in
FOC->Encoder.
Generate confgenerator.c and .h using VESC Tool.
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-08 21:05:46 -03:00
tipsmiller
3639c6c5f8
Remove custom app. Add new entry for adc ctrl type
2019-04-08 17:45:46 -06:00
Marcos Chaparro
de707e0975
Add SinCos encoder checks and fault management
...
Sin/Cos signals are checked to make sure the module of the vector
is larger than 1V and smaller than 1.65V. A working encoder will
never have both sin and cos signals at 0V (zero amplitude module).
Both sin and cos at 3.3V is also not a possible value.
Errors are logged independently for signals too large and for
signals too small, provinding the user more insight when an encoder
fault happens. In the terminal, the 'encoder' command will show
the error counts and error rates of the encoder being used.
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-02 10:37:15 -03:00
Marcos Chaparro
153deef9af
Add configurable low pass filtering to SinCos encoder analog signals
...
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-01 08:35:22 -03:00
Marcos Chaparro
b155d5219a
Basic SinCos encoder support
...
Reads sine and cosine on ADC_IND_EXT and ADC_IND_EXT2, usually
used for ACCEL and REGEN inputs. Provides offset and gain
compensation and is implemented using floating point math.
Note it includes the full mc_interface.h into encoder.c only
to access the ADC readings, and no filtering is performed on
the signals.
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-04-01 08:35:22 -03:00
Benjamin Vedder
1161f8417c
Added SWD programming support (based on Black Magic Probe) and open loop duty cycle control
2019-03-31 10:49:18 +02:00
Benjamin Vedder
65298263b6
75/300 R2 support, terminal sync cmd, IMU support, option to disable permanent UART, collected timer functions in one place
2019-03-10 14:57:42 +01:00
vadim
f668b89db5
trigger a fault when AS5047 encoder SPI communication is broken
2019-02-25 14:43:02 +02:00
Marcos Chaparro
32cf05629d
Resolve merge conficts with major 2019 release
...
Signed-off-by: Marcos Chaparro <mchaparro@powerdesigns.ca>
2019-02-18 20:25:52 -03:00
Benjamin Vedder
123bb00ab4
Major 2019 update
2019-02-18 19:30:19 +01:00
Marcos Chaparro
17f97763c0
Extend watchdog coverage with IWDG, a watchdog running from an independent LF oscillator. If any of the threads being monitored does not report for more than 12ms, a reset will be asserted. When a WDG reset happens, the user can see it in the fault logs from vesc tool
...
Signed-off-by: Marcos Chaparro <mchaparro@paltatech.com>
2019-01-24 12:19:44 -03:00
Marcos Chaparro
f1978ac5b4
Stronger filtering on gate driver supply voltage sensing. Add that voltage to fault logs
...
Signed-off-by: Marcos Chaparro <mchaparro@paltatech.com>
2019-01-18 19:03:53 -03:00
Marcos Chaparro
34bacefe99
Configure Brown Out Reset to keep mcu under reset until VDD reaches 2.7V. Configure Programmable Voltage Detector to interrupt and log a fault when mcu VDD drops below 2.9V.
...
Signed-off-by: Marcos Chaparro <mchaparro@paltatech.com>
2019-01-08 11:36:42 -03:00
Marcos Chaparro
89e6022698
Gate driver supply voltage monitoring
...
Signed-off-by: Marcos Chaparro <mchaparro@paltatech.com>
2018-12-12 20:03:12 -03:00
Benjamin Vedder
a20c35b338
FW 3.39: AUX pin support, some refactoring
2018-07-06 21:20:54 +02:00
Benjamin Vedder
22dc2ce33c
FW 3.37: FOC KI temp comp, configurable foc current filter
2018-03-24 22:32:58 +01:00
Benjamin Vedder
f7d0897c73
Added handbrake function to the simple CAN interface
2018-03-02 11:48:49 +01:00
Peemouse
29c771d7c5
v3.35 - Add option to power NRF module off
2018-02-17 17:59:21 +01:00
Benjamin Vedder
5348662197
FW 3.32: Configurable CAN baud rate
2017-11-08 14:07:35 +01:00
Benjamin Vedder
6277cf74ca
FW 3.31: Acc temp dec option, PID for APP_ADC
2017-10-27 21:29:12 +02:00
Benjamin Vedder
79bfbe6234
FW3.28: dual throttle curves, ntc beta factor config, board file added
2017-09-06 21:13:28 +02:00
Benjamin Vedder
f141157358
First official commit after the VESC Project release
2017-09-04 21:12:43 +02:00
Benjamin Vedder
bb2bfa3b9c
FW 3.9: Final float serialization update, new option to invert motor direction, UUID readout
2016-11-06 18:14:06 +01:00
Benjamin Vedder
5dbc94c525
FW 3.7
2016-11-04 15:18:34 +01:00
Benjamin Vedder
cb2a205cb8
FW 2.17: as5047 support, change sensor port mode in conf, better encoder detection, FOC ah and wh counter fixes
2016-04-27 15:32:32 +02:00
Benjamin Vedder
08a27cfbbd
FW 1.16: Hall sensor position control, brake at 0RPM setpoint in FOC, FOC parameter detection fix
2016-02-24 21:19:44 +01:00
Benjamin Vedder
d52906fbe8
FW 2.15: NRF configuration, PPM and ADC app duty mode scaling to max duty
2016-02-09 12:25:13 +01:00
Lucas Pleß
294d80b777
added ADC2 analog brake option
2016-02-02 16:28:55 +01:00
Benjamin Vedder
e6ea308a48
FW 2.10: FOC hybrid hall sensor support with interpolation
2016-01-27 23:57:23 +01:00
Benjamin Vedder
90986c31de
FW 2.9: NRF updates (nunchuk has to be updated too), nunchuk command, small can fix, custom app data command
2016-01-24 13:44:51 +01:00
Benjamin Vedder
42c1b79a08
FW 2.7: Better encoder support, small UART and CAN fixes, NRF commands preparation
2015-12-28 01:50:23 +01:00
Benjamin Vedder
ff090fd4e0
FW 2.3: MAJOR UPDATE: FOC!!
2015-12-08 21:01:23 +01:00
Benjamin Vedder
c4ff81e849
Ported to ChibiOS 3, refactoring, cleanup, added safe start delay after fault for PPM app, removed unused ST libraries
2015-10-08 23:09:39 +02:00
Benjamin Vedder
06129bb66c
FW 1.13: Hw 4.8 support, new CC implementation for nunchuk, refactoring, custom app and hw config support
2015-09-17 23:24:55 +02:00
Benjamin Vedder
c3e82f7651
Soft battery cutoff, more BLDC Tool parameters
2015-08-26 23:12:39 +02:00
Benjamin Vedder
58d892935d
PPM dec fix, current sampling updates, ADC cruise control, commutation fix, higher switching frequency, refactoring
2015-08-23 18:26:05 +02:00
Benjamin Vedder
f032111b9b
NRF updates, better servo output support
2015-07-31 23:26:50 +02:00
Benjamin Vedder
24380c3fc0
New hall sensor implementation with hybrid mode and connection/order auto detection
2015-06-19 23:38:46 +02:00
Benjamin Vedder
87932662b7
Long packet support, configurable min and max duty, longer CAN buffer, default parameter changes, appconf ack fix, refactoring
2015-05-20 16:13:48 +02:00
Benjamin Vedder
bc7a779632
Bootloader support, CAN fixes
2015-05-08 22:53:59 +02:00
Benjamin Vedder
5a5ccfb4c3
ADC app added, nunchuk RPM filter, FW version added, feedback on appconf and mcconf set
2015-05-04 23:25:43 +02:00
Benjamin Vedder
85f0073105
PPM updates and safe start implementation
2015-05-01 01:57:55 +02:00
Benjamin Vedder
d8830a2543
Option to switch CAN off, optimization to send short forwarded commands over CAN in just one frame
2015-04-27 20:43:02 +02:00
Benjamin Vedder
607e99d211
Configuration over CAN, first implementation of position control, more configuration options
2015-04-27 00:02:32 +02:00
Benjamin Vedder
1ee40ce5ba
Median filter option for PPM input
2015-04-20 22:09:53 +02:00
Benjamin Vedder
bc0415c1bb
First implementation of DC motor support
2015-04-12 18:23:17 +02:00
Benjamin Vedder
2ccb52514e
Encoder support, NRF nunchuk support
2015-04-11 10:07:36 +02:00
Benjamin Vedder
3b43648803
Show battery level on ws2812 LEDs
2015-03-07 14:56:25 +01:00
Benjamin Vedder
828cdd92f8
Chuk and PPM config structs, phase advance fixes and implementation for delay comm mode, CAN fixes and status message implementation, multi-esc mode for PPM and Chuk, traction control for PPM and chuk, CAN id config, multi-esc and traction control config, ADC sampling change, hall-sensor read bug fix for HW45+
2015-02-19 21:20:07 +01:00
Benjamin Vedder
b7e5692cc1
Over temp fault code
2015-01-23 00:40:09 +01:00
Benjamin Vedder
8dc8ffe2c7
Nunchuk ramping, ws2811 configurable pin (Requieres latest BLDC_Tool)
2014-12-20 12:52:38 +01:00
Benjamin Vedder
434cd04b86
Added max ERPM in CC mode parameter (NOTE: Requires latest BLDC_Tool)
2014-12-13 11:46:26 +01:00
Benjamin Vedder
bc4409ba14
Full brake current estimation (NOTE: Extra parameter added, so update BLDC_Tool)
2014-12-13 01:31:54 +01:00
Benjamin Vedder
9ff0f99593
WS2811/WS2812 LED driver to use LEDs for turn and brake lights, etc
2014-12-09 00:11:29 +01:00
Benjamin Vedder
5675c4f485
First CAN implementation
2014-12-07 04:30:25 +01:00
Benjamin Vedder
42cab4c18d
Added voltage to fault log
2014-11-27 20:56:17 +01:00
Benjamin Vedder
33c81db930
Deadband fix, configurable temperature limit
2014-11-25 21:05:46 +01:00
Benjamin Vedder
f7cda79d1b
HW45-implementation, temp-protection, nunchuk-fix, i2c-fixes
2014-10-19 19:31:06 +02:00
Benjamin Vedder
81a6d84113
Nunchuk implementation (Nyko Kama tested), mah and wh counting
2014-10-19 01:00:53 +02:00
Benjamin Vedder
2119242b43
Soft RPM limit for current mode in ppm app
2014-09-21 19:29:26 +02:00
Benjamin Vedder
e27df0235f
Command to get decoded servo value
2014-09-20 15:23:36 +02:00
Benjamin Vedder
10bbe73206
Global timeout implementation
2014-09-20 13:41:18 +02:00
Benjamin Vedder
1d04f0314b
Added gpl to some files
2014-09-20 03:27:06 +02:00
Benjamin Vedder
d6beda7b47
Complete servo-decoding rewrite, common command module, full access to everything over uart, more ppm options
2014-09-20 03:22:38 +02:00
Benjamin Vedder
2e723ece6f
App configuration, eeprom emu fix, reboot command
2014-09-18 23:00:14 +02:00
Benjamin Vedder
6d4e55051c
Prepared applications for runtime configuration
2014-09-17 21:05:57 +02:00
Benjamin Vedder
e4c7fca84d
Tachometer improvement and rpm-dep bug fix
2014-09-16 10:44:56 +02:00
Benjamin Vedder
1f1a8af1d7
Full runtime configuration support with flash storage
2014-09-15 02:39:58 +02:00
Benjamin Vedder
2cc53de346
Major USB communication protocol re-write and beginning runtime motor parameter configuration
2014-09-14 23:08:22 +02:00