* more unification
* hip stub
* comment
* guard
* channel idx
* include
* hip
* move in to engine
* hip9011
* dead stuff
* dead
* fsio
* lcd
* more dead
* Typo fix
* flash_main: always allow to write settings to ext NOR while running
* mc33810: do not enable outputs right after undervoltage
Wait for next active signal
* QSPI flash: set correct dummy cycles for fast read command
* board subaru: fix connector pinout. again.
* board subaru: fix SDMMC pin configuration
* board subaru: fix DMA conflict SPI4_RX vs SDMMC2
* flash_main.cpp: reorder code for easy integration of ext storage
* Add EFI_STORAGE_INT_FLASH option
Default set to TRUE
* Add ChibiOS's Managed Flash Storage to build
* Add support for QSPI flash (SST26F064A tested)
* board: subaru: enable WSPI and NOR flash drivers
* Add option to save settings on ext flash MFS partition
* board: subaru: store settings on QSPI NOR flash
* big pch energy
* put back ramdisk stub
* tests are happy
* h743 nucleo
* kinetis
* I love deleting code!
* make stepper happy
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* detect hse
* implementation
* these boards don't need to set their own HSECLK
* assertions
* name
* tweaks
* how did this compile?
* s
* biiiig comment
* this script doesn't need to set 25mhz any more
* ....or PLLM
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* CAN HW: use designated initizalization
* board subaru eg33: set CAN transceiver EN to active state constantly
While FW does not handle CAN transceiver's EN signal
* rename
* core
* structing
* more
* makefile
* structing
* 6240 compiles
* explicit cast instead of implicit narrowing
* 8888
* no extern C
* fix tests build
* extern "C"
* 33810
* 8860
* 33810
* linker
* unbreak master
* don't need that if compiling as C++
* bump config
* fix test
* tests
* unit tests bad merge
* build
* move subaru logic to cpp file
* cpp goodness
* hpp include
* this is probably the right thing to do
* simulator
* engine math: extrant getFiringOrderTable for reuse
* engine math: getNextFiringCylinderId helper
* introduce knock_logic: first member is getCylinderKnockBank()
moved from software_knock.cpp
* hip9011: support two inputs/banks
* fix CI
* Board Subaru EG33: populated with TPIC8101 with Advanced mode
* hip9011: test communication in advanced mode
* hip9011: handle situation when chip is already in advanced mode
* Board Subaru EG33: cylinder to knock bank mapping
* hip9011: count spi transactions in advansed mode too
* hip9011: reset incalid responce counter after chip initialization
* hip9011: make debug output more structured
* carve out UART specific
* implement channel
* config cleanup
* use new config
* bootloader
* dead code
* s
* h7 inherits f7
* oops
* ok now it's right
* tests
* cleanup
* call setup
* put that in its own file
* cleanup
* format
* guard
* not needed
* improve guarding
* portable
* allow override of uart mode
* fixes for bootloader
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* new apis
* dedicated USB path
* move decl
* init
* don't init usb twice
* guard
* check that we're initialized before using TS
* comment
* guard
* guard USB
* brain doesn't go good
* make tests happy
* dead define
* cypress
* ifdef != if
* s
* include priority
* don't start a thread we know we don't need
* bad-ish merge
* const
* why did this code exist...?
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
Matthew Kennedy
Andrey G
Andrey
GitHub build-firmware Action
rusefillc