rusefi-full/firmware/tunerstudio/rusefi.input

; this is TunerStudio project for www.rusefi.com DIY engine management system
;
; rusefi.ini is generated by invoking gen_config.bat (look inside for the exact command to run it outside of Windows)
; inputs are rusefi.input template and rusefi_config.txt file
;
;
; In TunerStudio some fields have little question mark on the left of the name for additional field tips.
; Those tips are defined in ../integraion/rusefi_config.txt file for example
;
;     float bias_resistor;+Pull-up resistor value on your board;"Ohm"
; here 'bias_resistor' is internal field name and the text between semicolons is what produces the tooltip
; Note that '+' sign is required after first semicolon for tooltop to appear in TunerStudio
;
;
;

; this should stop TS from looking for the CAN ID in the 2nd byte location and allow the page reads to work correctly.
enable2ndByteCanID = false

;#unset tuneByMAF

[SettingGroups]
   ; the referenceName will over-ride previous, so if you are creating a 
   ; settingGroup with a reference name of lambdaSensor, it will replace the 
   ; setting group defined in the settingGroups.xml of the TunerStudio config
   ; folder. If is is an undefined referenceName, it will be added.
   ; keyword    =  referenceName,  DisplayName

    settingGroup = tuneVeMode, "VE Autotune Mode"
      settingOption = tuneByTPS, "TPS-Based (See Injection -> Inj.Settings)"
      settingOption = tuneByMAF, "MAF-Based"
      settingOption = tuneByLoad, "Load-Based (Default)"

;    settingGroup = fAlgorithmSetting, "Fuel Logic / Tables"  
;    settingOption = FA_PLAIN_MAF, "Plain MAF"
;    settingOption = FA_TPS, "AlphaN/TPS"
;    settingOption = DEFAULT, "Speed Density" ; DEFAULT will be over looked and this will fall into the #else block of the statement.



[TunerStudio]
   queryCommand   = "S"
   versionInfo    = "V"  ; firmwave version for title bar.
   signature    = @@TS_SIGNATURE@@ ; signature is expected to be 7 or more characters.

[Constants]
; new packet serial format with CRC
   messageEnvelopeFormat = msEnvelope_1.0

   endianness          = little
   nPages              = 1
  

   pageIdentifier      = "\x00\x00"
   pageReadCommand     = "R\x00\x00%2o%2c"
   burnCommand         = "B\x00\x00"
   pageActivate        = "P\x00\x00"
   pageValueWrite      = "W\x00\x00%2o%v"
   pageChunkWrite      = "C\x00\x00%2o%2c%v"
;   crc32CheckCommand   = "k%2i%2o\xB8\x36"
	;
	; TODO: interesting - 0x36B8 equals 14008 which looks like pageSize at some point in the past? is this a defect here - should
	; we have current pageSize or (pageSize + 8) here?
	;
   crc32CheckCommand   = "k\x00\x00\x00\x00\x36\xB8"

;communication settings
   pageActivationDelay = 500 ; Milliseconds delay after burn command. See https://sourceforge.net/p/rusefi/tickets/77/
;e.g. put writeblocks off and add an interwrite delay
   writeBlocks = on
   interWriteDelay = 10
   blockReadTimeout    = 3000; Milliseconds general timeout
   
 ; delayAfterPortOpen = 500  
   
   blockingFactor = 400 ; max chunk size
;end communication settings

   ;  name      			= bits,   type, offset,  bits
   ;  name           		= array,  type, offset,  shape, units,     scale, translate,    lo,      hi, digits
   ;  name       			= scalar, type, offset,         units,     scale, translate,    lo,      hi, digits

; see PAGE_0_SIZE in C source code    
; CONFIG_DEFINITION_START

; this section will be generated automatically by ConfigDefinition.jar based on rusefi_config.txt

; CONFIG_DEFINITION_END
	idleRpmPid_offset = "Constant base value"
	idleRpmPid_periodMs = "PID recalculation period"
	

[Tuning]
   spotDepth       =   2 ; 0 = no indicators, 1 = Z only, 2 = XYZ indicators.
   cursorDepth     =   2 ; Same as spot depth.

   gaugeColumns = 1 ; Only 1 or 2 are valid.

   pageButtons  = "&EGO"
   gauge1       = RPMGauge	
   gauge2       = afr1Gauge
   gauge3		= MAPGauge
   gauge4		= veValueGauge


[LoggerDefinition]
  ; valid logger types: composite, tooth, trigger, csv
  loggerDef = compositeLogger, "Primary Trigger Logger", tooth
        startCommand = "l\x01"
        stopCommand  = "l\x02"
        dataReadCommand = "L"
        dataReadTimeout = 10000 ; time in ms
        dataReadyCondition = { toothLogReady }

       ; recordDef = headerLen, footerLen, recordLen
       recordDef =   0,   0,   2; in bytes, the recordLen is for each record, currently limited to 4 bytes

       ; uint16 that stores 1/100 second
       recordField = toothTime, "tooth", 0, 16, 0.01, "ms"


[VeAnalyze]

        ;    tableName,  lambdaTargetTableName, lambdaChannel, egoCorrectionChannel, activeCondition
#if tuneByMAF
       veAnalyzeMap = fuelTableTbl, afrTableTbl, AFRValue, egoCorrection, { 1 }
#else
       veAnalyzeMap = veTableTbl, afrTableTbl, AFRValue, egoCorrection, { 1 }
#endif
       lambdaTargetTables = afrTableTbl, afrTSCustom

       ; filter =  Name,        "DisplayName", outputChannel, operator, defaultVal, userAdjustable
        filter = minRPMFilter, "Minimum RPM", RPMValue,           <       , 500,      , true

#if CELSIUS
         filter = minCltFilter, "Minimum CLT", coolant,       <       , 60,       , true
#else
         filter = minCltFilter, "Minimum CLT", coolant,       <       , 160,      , true
#endif

         filter = deltaTps, "dTPS", deltaTps       >       , 50,      , true

		filter = VBatt, "VBatt", VBatt       <       , 12,      , true

         filter = minTps, "Minimum TPS", TPSValue,       <       , 1,       , true


;[VeAnalyze]
;       fuelAnalyzeMap = fuelTableTbl, afrTableTbl, AFRValue, egoCorrection , { 1 }
;        filter = minRPMFilter, "Minimum RPM", RPMValue,           <       , 500,      , true



[OutputChannels]

; see TS_FILE_VERSION in firmware code
fileVersion = { 20171101 }

   ochGetCommand    = "O%2o%2c"

; see TS_OUTPUT_SIZE in console source code
   ochBlockSize     = 356

;
; see TunerStudioOutputChannels struct
;
      RPMValue        = scalar,  U32,      0,             "RPM",            1,   0.00000
#if CELSIUS
      coolant         = scalar,  F32,      4,              "deg C",            1,       0.0
#else
      coolant         = scalar,  F32,      4,              "deg F",         {9/5},  17.77777
#endif
#if CELSIUS
      intake          = scalar,  F32,      8,              "deg C",            1,       0.0
#else
      intake          = scalar,  F32,      8,              "deg F",         {9/5},  17.77777
#endif
      TPSValue        = scalar,  F32,     12,               "%",            1,         0
      MAFValue        = scalar,  F32,     16,               "V",            1,         0
      AFRValue       = scalar,  F32,     20,             "AFR",            1,       0.0
      engineLoad      = scalar,	 F32,     24,	    "%",            1,       0.0 ; Blend of MAP and TPS, depends on algorithm
      VBatt	          = scalar,	 F32,     28,	            "V",            1,       0.0
      ; 10 bit TPS ADC value (from 0 to 1023 in 5v scale)
      tpsADC          = scalar,  U16,     32,             "ADC",            1,       0.0;
      tpsADC2         = scalar,  U16,     34,             "ADC",            1,       0.0;
      baroPressure    = scalar,  F32,     36,             "pres",           1,       0.0;
      MAPValue        = scalar,  F32,     40,              "MAP",           1,       0.0;
	  ; total fuel squirt duration (in MS) per engine cycle according to current CLT
	  crankingFuelMs  = scalar,  F32,     44,              "ms",            1,       0.0;
      baseFuel        = scalar,  F32,     48,              "ms",           1,         0
      tCharge         = scalar,  F32,     52,              "T",             1,       0.0;
      ignitionAdvance = scalar,  F32,     56,              "deg",           1,       0.0;
      sparkDwellValue = scalar,  F32,     60,              "ms",           1,       0.0;
      ; actual total Ms time per engine cycle with all corrections
      actualLastInjection      = scalar,  F32,     64,              "ms",           1,       0.0;
      debugFloatField1    = scalar,  F32,  68,            "val",           1,       0.0;
      
      hasSdCard       = bits,    U32,     72, [0:0], "true", "false";
	  isIgnitionEnabledIndicator=bits, U32,     72, [1:1], "true", "false";
	  ind_injection_enabled=bits,U32,     72, [2:2], "true", "false";
	  isCylinderCleanupEnabled=bits, U32, 72, [3:3], "true", "false";
	  isCylinderCleanupActivated=bits,U32,72, [4:4], "true", "false";
	  ind_fuel_pump   = bits,    U32,     72, [5:5], "true", "false";
	  ind_fan         = bits,    U32,     72, [6:6], "true", "false";
	  ind_o2_heater   = bits,    U32,     72, [7:7], "true", "false";
      ind_check_engine= bits,    U32,     72, [8:8], "true", "false";
      needBurn        = bits,    U32,     72, [9:9], "true", "false";
      ind_2nd_trigger_en=bits,   U32,     72, [10:10], "true", "false";
      clutchUpState    =bits,    U32,     72, [11:11], "true", "false";
      clutchDownState  =bits,    U32,     72, [12:12], "true", "false";
      knockEverIndicator=bits,   U32,     72, [13:13], "true", "false";
      knockNowIndicator=bits,    U32,     72, [14:14], "true", "false";
      brakePedalIndicator=bits,  U32,     72, [15:15], "true", "false";
      toothLogReady      =bits,  U32,     72, [16:16], "true", "false";
      acSwitchIndicator =bits,   U32,     72, [17:17], "true", "false";
      vehicleSpeedKph = scalar,  F32,     76,        "kph",   1,       0.0;
      
      ind_tps_error   = bits,    U32,     80, [0:0], "true", "false";
      ind_clt_error   = bits,    U32,     80, [1:1], "true", "false";
      ind_map_error   = bits,    U32,     80, [2:2], "true", "false";
      ind_iat_error   = bits,    U32,     80, [3:3], "true", "false";
      ind_isTriggerError = bits, U32,     80, [5:5], "true", "false";
      ind_hasFatalError=bits,    U32,     80, [6:6], "true", "false";
      ind_isWarnNow    =bits,    U32,     80, [7:7], "true", "false";
      firmwareTsVersion = scalar,U32,     84, "version_p",           1,         0
      egt1            = scalar,  S16,     88, "deg C",           1,         0
      egt2            = scalar,  S16,     90, "deg C",           1,         0
      egt3            = scalar,  S16,     92, "deg C",           1,         0
      egt4            = scalar,  S16,     94, "deg C",           1,         0
      egt5            = scalar,  S16,     96, "deg C",           1,         0
      egt6            = scalar,  S16,     98, "deg C",           1,         0
      egt7            = scalar,  S16,    100, "deg C",           1,         0
      egt8            = scalar,  S16,    102, "deg C",           1,         0
      rpmAcceleration = scalar,  F32,    104, "dRpm",         1,         0
      massAirFlowValue= scalar,  F32,    108, "Kg/h",         1,         0
      veValue         = scalar,  F32,    112, "ratio",        1,         0
      deltaTps        = scalar,  F32,    116, "ratio",        1,         0
      triggerErrorsCounter = scalar, U32,120, "counter",      1,         0
      engineLoadAccelExtra = scalar,F32, 124, "value",        1,         0
      tpsAccelFuel    = scalar,  F32,    128, "ms",           1,         0
      baroCorrection  = scalar,  F32,    132, "%",            1,         0
      pedalPosition   = scalar,  F32,    136, "%",            1,         0
      injectorDutyCycle= scalar, F32,    140, "%",            1,         0
      knockCount      = scalar,  U32,    144, "counter",      1,         0
      fuelTankLevel   = scalar,  F32,    148, "amount",       1,         0
      knockLevel      = scalar,  F32,    152, "Volts",        1,         0
      ; totalTriggerErrorCounter 156
      wallFuelAmount = scalar, F32,      160, "ms",           1,         0
      iatCorrection = scalar, F32,       164, "%",            1,         0
      wallFuelCorrection = scalar, F32,  168, "ms",           1,         0
      idleAirValvePosition = scalar, F32,     172, "percent",      1,         0
      currentTargetAfr = scalar, F32,    176, "ratio",      1,         0
      chargeAirMass = scalar, F32,       180, "g",      1,         0
      cltCorrection = scalar, F32,       184, "%",            1,         0
      fuelRunning = scalar, F32,         188, "g",      1,         0
      debugIntField1    = scalar,  S32,  192, "val",          1,       0.0;
      injectorLagMs     = scalar,  F32,  196,            "ms",           1,       0.0;
      debugFloatField2  = scalar,  F32,  200,            "val",           1,       0.0;
      debugFloatField3  = scalar,  F32,  204,            "val",           1,       0.0;
      debugFloatField4  = scalar,  F32,  208,            "val",           1,       0.0;
      debugFloatField5  = scalar,  F32,  212,            "val",           1,       0.0;
      debugIntField2    = scalar,  S32,   216, "val",          1,       0.0;
      debugIntField3    = scalar,  S32,   220, "val",          1,       0.0;
      timeSeconds       = scalar,  U32,   224, "sec",          1,       0.0;
      engineLoadDelta = scalar,F32, 228, "value",            1,         0
      speedToRpmRatio = scalar,F32, 232, "value",            1,         0
      warningCounter = scalar,U16, 236, "count",            1,         0
      
      lastErrorCode = scalar,U16, 240, "error",            1,         0
      
      internalMcuTemperature = scalar,F32, 244, "C",            1,         0
      vvtPosition = scalar,F32, 248, "deg",            1,         0
      engineMode    = scalar,  U32,   252, "em",          1,       0.0;
      debugFloatField6  = scalar,  F32,  256,            "val",           1,       0.0;
      debugFloatField7  = scalar,  F32,  260,            "val",           1,       0.0;
      firmwareVersion = scalar,U32,     264, "version_f",           1,         0
      fuelPidCorrection        = scalar,  F32,     268,              "ms",           1,         0
      coilDutyCycle        = scalar,  F32,     272,              "perc",           1,         0
      accelerationX        = scalar,  S16,     276,              "G",           0.01,         0
      accelerationY        = scalar,  S16,     278,              "G",           0.01,         0
      oilPressure	   = scalar,  F32,     280,		 "kPa",			1, 0.0
      fuelConsumptionPerHour=scalar,  F32,     284,		 "kPa",			1, 0.0
      injectionOffset       = scalar, F32,     288,              "deg",                 1,     0;
      debugIntField4    = scalar,  S16,  292, "val",          1,       0.0;
      debugIntField5    = scalar,  S16,  294, "val",          1,       0.0;
	  recentErrorCode0 = scalar,U16, 296, "error",            1,         0
      recentErrorCode1 = scalar,U16, 298, "error",            1,         0
      recentErrorCode2 = scalar,U16, 300, "error",            1,         0
      recentErrorCode3 = scalar,U16, 302, "error",            1,         0
      recentErrorCode4 = scalar,U16, 304, "error",            1,         0
      recentErrorCode5 = scalar,U16, 306, "error",            1,         0
      recentErrorCode6 = scalar,U16, 308, "error",            1,         0
      recentErrorCode7 = scalar,U16, 310, "error",            1,         0
      etbTarget        = scalar,F32, 312, "%", 1, 0
      etb1DutyCycle    = scalar,F32, 316, "%", 1, 0
      etb1Error        = scalar,F32, 320, "%", 1, 0


;
; see TunerStudioOutputChannels struct
;

; todo: generate this section programatically
	LM_PLAIN_MAF = {0},
	LM_ALPHA_N = {1},
	LM_MAP = {2},
	LM_SPEED_DENSITY = {3},
	LM_REAL_MAF = {4}

      egoCorrection   = { 100 }
      time            = { timeNow }
;      engineLoad      = { fuleAlgorithm == 0 ? MAF : TPS }

[PcVariables]
    wueAfrTargetOffset = array, S16, [ 16], ":1",   0.1, 0.0, -3.0, 3.0, 1;
    wueAnalRecommend   = array, U08, [ 16], "%",  1.00, 0.0, 100, 255.00, 0

[ConstantsExtensions]
    defaultValue = wueAfrTargetOffset, -1.5 -1.4 -1.15 -0.95 -0.775 -0.65 -0.5625 -0.5 -0.4375 -0.375 -0.3125 -0.25 -0.1875 -0.125 -0.0625 0

[CurveEditor]
;	xAxis       =  leftValue, rightValue, step
;	yAxis       =  bottomValue, topValue, step


	curve = knockThresholdCurve, "Engine knock threshold RPM based"
      columnLabel = "RPM", "Threshold"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  8, 10
      xBins       = knockNoiseRpmBins, RPMValue
      yBins       = knockNoise
      gauge       = RPMGauge

	curve = narrowToWideOxygenCurve, "Narrow to Wideband approximation"
      columnLabel = "Voltage", "AFR"
      xAxis       =  0, 6, 10
      yAxis       =  0,  28, 10
      xBins       = narrowToWideOxygenBins
      yBins       = narrowToWideOxygen
      gauge       = afr1Gauge

   curve = fsioCurve1, "FSIO Curve #1"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -155,  150, 10
      xBins       = fsioCurve1Bins
      yBins       = fsioCurve1
      
   curve = fsioCurve2, "FSIO Curve #2"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -150,  150, 10
      xBins       = fsioCurve2Bins
      yBins       = fsioCurve2

   curve = fsioCurve3, "FSIO Curve #3"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = fsioCurve3Bins
      yBins       = fsioCurve3

   curve = fsioCurve4, "FSIO Curve #4"
      columnLabel = "X", "Y"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = fsioCurve4Bins
      yBins       = fsioCurve4

   curve = mapAccelTaper, "Engine Load Acceleration Enrichment Taper"
      columnLabel = "Distance", "Multiplier"
      xAxis       =  0, 128, 10
      yAxis       = -5,  5, 10
      xBins       = mapAccelTaperBins
      yBins       = mapAccelTaperMult

	curve = dwellCorrection, "Dwell time RPM based"
      columnLabel = "RPM", "Dwell"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  30, 10
      xBins       = sparkDwellRpmBins, RPMValue
      yBins       = sparkDwellValues
      gauge       = RPMGauge
    
   curve = map_samplingAngleCurve, "MAP Sampling Start Angle"
      columnLabel = "RPM", "Angle"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  180, 10
      xBins       = map_samplingAngleBins, RPMValue
      yBins       = map_samplingAngle
	  gauge       = MAPGauge
   
   curve = map_samplingWindowCurve, "MAP Sampling Duration"
      columnLabel = "RPM", "Window"
      xAxis       =  0, 8000, 10
      yAxis       =  0,  180, 10
      xBins       = map_samplingWindowBins, RPMValue
      yBins       = map_samplingWindow
	  gauge       = MAPGauge

   curve = injectorsDeadTime, "Injector Dead Time by VBatt"
      columnLabel = "Voltage", "Dead Time"
      xAxis       =  8, 21, 10
      yAxis       = -3,  3, 10
      xBins       = injector_battLagCorrBins, VBatt
      yBins       = injector_battLagCorr
      gauge       = VBattGauge
      
   curve = mafDecodingCurve, "MAF sensor"
      columnLabel = "Voltage", "kg/hour"
      xAxis       =  -1, 6, 10
      yAxis       = -30,  1300, 10
      xBins       = mafDecodingBins, MAFValue
      yBins       = mafDecoding
      gauge       = MAFGauge

   curve = iatFuelCorrCurve, "Intake air temperature fuel Multiplier"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       =  -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  2, 11
      xBins       = iatFuelCorrBins, intake
      yBins       = iatFuelCorr
      gauge       = IATGauge
	
	curve = cltTimingCorrCurve, "Warmup timing correction"
      columnLabel = "Coolant", "Extra"
#if CELSIUS
      xAxis       =  -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  50, 10
      xBins       = cltTimingBins, coolant
      yBins       = cltTimingExtra
      gauge       = CLTGauge

	curve = cltFuelCorrCurve, "Warmup fuel manual Multiplier"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       =  -40, 100, 10
#else
      xAxis       =  -40, 210, 10
#endif
      yAxis       =  0,  3, 10
      xBins       = cltFuelCorrBins, coolant
      yBins       = cltFuelCorr
      gauge       = CLTGauge

	curve = crankingCltCurve, "Cranking Coolant Temperature Multiplier"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       =  -40, 100, 10
#else
      xAxis       =  -40, 210, 10
#endif
      yAxis       =  0,  3, 10
      xBins       = crankingFuelBins, coolant
      yBins       = crankingFuelCoef
      gauge       = CLTGauge

	curve = etbTpsBiasCurve, "Electronic TB Bias Curve"
      columnLabel = "TPS", "duty bias"
      xAxis       =  0, 100, 10
      yAxis       =  0,  100, 10
      xBins       = etbBiasBins, TPSValue
      yBins       = etbBiasValues
      gauge       = TPSGauge

	curve = crankingTpsCurve, "Cranking TPS Multiplier"
      columnLabel = "TPS", "Multiplier"
      xAxis       =  0, 100, 10
      yAxis       =  0,  3, 10
      xBins       = crankingTpsBins, TPSValue
      yBins       = crankingTpsCoef
      gauge       = TPSGauge

	curve = crankingDurationCurve, "Cranking Duration Multiplier"
      columnLabel = "Engine Cycle", "Multiplier"
      xAxis       =  0, 1000, 10
      yAxis       =  0,  3, 10
      xBins       = crankingCycleBins
      yBins       = crankingCycleCoef


	curve = cltIdleCurve, "Warmup Idle multiplier"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       = -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  3, 10
      xBins       = cltIdleCorrBins, coolant
      yBins       = cltIdleCorr
      gauge       = CLTGauge

	curve = iacCoastingCurve, "Coasting IAC Position for Auto-Idle"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       = -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  100, 10
      xBins       = iacCoastingBins, coolant
      yBins       = iacCoasting
      gauge       = idleAirValvePositionGauge

	curve = cltCrankingCurve, "Cranking Idle Air multiplier"
      columnLabel = "Coolant", "Multiplier"
#if CELSIUS
      xAxis       = -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  3, 10
      xBins       = cltCrankingCorrBins, coolant
      yBins       = cltCrankingCorr
      gauge       = CLTGauge

	curve = cltIdleRPMCurve, "Idle Target RPM"
      columnLabel = "Coolant", "RPM"
#if CELSIUS
      xAxis       = -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0, 8000, 10
      xBins       = cltIdleRpmBins, coolant
      yBins       = cltIdleRpm, RPMValue
      gauge       = CLTGauge

	curve = idleAdvanceCurve, "Idle Advance Angle"
      columnLabel = "RPM", "degrees"
      xAxis       = 0, 8000, 10
      yAxis       = -100, 100, 10
      xBins       = idleAdvanceBins, RPMValue
      yBins       = idleAdvance
      gauge       = RPMGauge

	curve = idleVeCurve, "Idle VE"
      columnLabel = "RPM", "%"
      xAxis       = 0, 8000, 10
      yAxis       = 0, 250, 10
      xBins       = idleVeBins, RPMValue
      yBins       = idleVe
      gauge       = afr1Gauge
    
	curve = crankingAdvanceCurve, "Cranking Advance Angle"
      columnLabel = "RPM", "degrees"
      xAxis       = 0, 8000, 10
      yAxis       = -100, 100, 10
      xBins       = crankingAdvanceBins, RPMValue
      yBins       = crankingAdvance
      gauge       = RPMGauge

	curve = warmupTargetAfrCurve, "CLT-based target AFR"
      columnLabel = "Coolant", "Correction"
#if CELSIUS
      xAxis       = -40, 120, 10
#else
      xAxis       =  -40, 250, 10
#endif
      yAxis       =  0,  50, 10
      xBins       = warmupTargetAfrBins, coolant
      yBins       = warmupTargetAfr
      gauge       = CLTGauge

    curve = wueAfrTargetOffsetCurve, "AFR Target Temperature Adjustment"
      columnLabel = "Coolant", "AFR Offset"
#if CELSIUS
      xAxis       = -40, 200, 9
#else
      xAxis       = -40, 400, 9
#endif
      yAxis       =   -3,  1, 5
      xBins       = cltFuelCorrBins, coolant
      yBins       = wueAfrTargetOffset
      gauge      = cltGauge

    curve = wueAnalyzer_warmup_curve, "Warmup Enrichment"
      columnLabel = "Coolant", "Current WUE", "Coolant", "Corrected"
#if CELSIUS
      xAxis       = -40, 200, 9
#else
      xAxis       = -40, 400, 9
#endif
      yAxis       =   90,  500, 6
      xBins       = cltFuelCorrBins, coolant
      yBins       = cltFuelCorr
      yBins       = wueAnalRecommend
      ;gauge       = cltGauge
          
      lineLabel   = "Warmup Correction"
      lineLabel   = "Recommended WUE"

[TableEditor]
   ;       table_id,    map3d_id,    "title",      page

   table = fuelTableMAFTbl,  fuelTableMAFMap,  "Fuel Table",   1
   	  topicHelp = "fuelHelp"
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  MAFValue
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = fuelTableTPSTbl,  fuelTableTPSMap,  "Fuel Table",   1
   		topicHelp = "fuelHelp"
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  TPSValue
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = fuelTableELTbl,  fuelTableELMap,  "Fuel Table",   1
   topicHelp = "fuelHelp"
      ;       constant, variable
      xBins       = fuelRpmBins,  RPMValue
      yBins       = fuelLoadBins,  engineLoad
      zBins       = fuelTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

; move table into a panel? or find a way to add a link to https://rusefi.com//wiki/index.php?title=Manual:Software:TPSTPS
   table = tpsTpsAccelTbl,  tpsTpsAccelMap,  "TPS/TPS Acceleration Extra Fuel(ms)",   1
   	topicHelp = "tpstpsHelp"
      xBins       = tpsTpsAccelFromRpmBins,  TPSValue
      yBins       = tpsTpsAccelToRpmBins,  TPSValue
      zBins       = tpsTpsAccelTable
    
      
   table = fsioTable1Tbl,  fsioTable1Map,  "FSIO Table #1",   1
      xBins       = fsioTable1RpmBins,  RPMValue
      yBins       = fsioTable1LoadBins,  engineLoad
      zBins       = fsioTable1

   table = fsioTable2Tbl,  fsioTable2Map,  "FSIO Table #2",   1
      xBins       = fsioTable2RpmBins,  RPMValue
      yBins       = fsioTable2LoadBins,  engineLoad
      zBins       = fsioTable2

   table = fsioTable3Tbl,  fsioTable3Map,  "FSIO Table #3",   1
      xBins       = fsioTable3RpmBins,  RPMValue
      yBins       = fsioTable3LoadBins,  engineLoad
      zBins       = fsioTable3

   table = fsioTable4Tbl,  fsioTable4Map,  "FSIO Table #4",   1
      xBins       = fsioTable4RpmBins,  RPMValue
      yBins       = fsioTable4LoadBins,  engineLoad
      zBins       = fsioTable4

   table = baroCorrTbl,  baroCorrMap,  "Baro Correction",   1
      ;       constant, variable
      xBins       = baroCorrRpmBins,  RPMValue
      yBins       = baroCorrPressureBins,  baroPressure
      zBins       = baroCorrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = ignitionTableTbl,  ignitionTableMap,  "Ignition Table",   1
      ;       constant, variable
      xBins       = ignitionRpmBins,  RPMValue
#if   FA_PLAIN_MAF
      yBins       = ignitionLoadBins,  MAFValue
#elif FA_TPS
      yBins       = ignitionLoadBins,  TPSValue
#else
      yBins       = ignitionLoadBins,  engineLoad
#endif

      zBins       = ignitionTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"
	
   table = ignitionTpsTableTbl,  ignitionTableMap,  "Ignition TPS Table",   1
      ;       constant, variable
      ; Currently we share ignitionRpmBins between two advance tables... Is it ok?
      xBins       = ignitionRpmBins,  RPMValue
      yBins       = ignitionTpsBins,  TPSValue

      zBins       = ignitionTpsTable
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"
	
   table = ignitionIatCorrTableTbl,  ignitionIatCorrTableMap,  "Ignition Intake Air Temp correction",   1
      ;       constant, variable
      xBins       = ignitionIatCorrRpmBins,  RPMValue
      yBins       = ignitionIatCorrLoadBins,  intake
      zBins       = ignitionIatCorrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

   table = veTableTbl,  veTableMap,  "VE Table",   1
      ;       constant, variable
      xBins       = veRpmBins,  RPMValue
#if tuneByTPS
      yBins       = ignitionTpsBins,  TPSValue
#else
      yBins       = veLoadBins,  MAPValue
#endif
      zBins       = veTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"


   table = injPhaseTableTbl,  injPhaseTableMap,  "Injection Phase",   1
   		topicHelp = "fuelHelp"
      ;       constant, variable
      xBins       = injPhaseRpmBins,  RPMValue
      yBins       = injPhaseLoadBins,  engineLoad
      zBins       = injectionPhase
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(Later)", "(Sooner)"

   table = pedalToTpsTbl,  pedalToTpsMap,  "ETB Pedal to TPS",   1
      ;       constant, variable
      xBins       = pedalToTpsRpmBins,  RPMValue
      yBins       = pedalToTpsPedalBins,  pedalPosition
      zBins       = pedalToTpsTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(Later)", "(Sooner)"


   table = afrTableTbl,  afrTableMap,  "Target AFR Table",   1
      ;       constant, variable
      xBins       = afrRpmBins,  RPMValue
      yBins       = afrLoadBins,  MAPValue
      zBins       = afrTable
;      gridHeight  = 2.0
      gridOrient  = 250,   0, 340 ; Space 123 rotation of grid in degrees.
      upDownLabel = "(RICHER)", "(LEANER)"

[GaugeConfigurations]

gaugeCategory = Sensors - Extra 2
   egt1Gauge         = egt1, "EGT#1", "C", 0, 2000
   egt2Gauge         = egt2, "EGT#2", "C", 0, 2000
   egt3Gauge         = egt3, "EGT#3", "C", 0, 2000
   egt4Gauge         = egt4, "EGT#4", "C", 0, 2000
   egt5Gauge         = egt5, "EGT#5", "C", 0, 2000
   egt6Gauge         = egt6, "EGT#6", "C", 0, 2000
   egt7Gauge         = egt7, "EGT#7", "C", 0, 2000
   egt8Gauge         = egt8, "EGT#8", "C", 0, 2000
   rpmAccelerationGa = rpmAcceleration,     "rpm delta",        "dRpm",        0,      3,       0,      1,       3,     4,   1,   1
   knockCountGauge   = knockCount,"Knock count",           "count",        0,    120,      10,     10,     100,   100,   1,   1
   knockLevelGauge   = knockLevel,"Knock level",           "volts",        0,      7,      10,     10,     100,   100,   1,   2
   fuelTankLevelGauge   = fuelTankLevel,"Fuel level",           "x",        0,      7,      10,     10,     100,   100,   1,   2
   speedToRpmRatioGauge = speedToRpmRatio, "speed2rpm", "",     0,   100,     0,    0,    100,  100,   4,   4

gaugeCategory = ECU Status
   warningCounterGauge = warningCounter, "Warning count", "",     0,   100,     0,    0,    100,  100,   0,   0
   lastErrorCodeGauge = lastErrorCode, "Last error", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   triggerErrorsCounterGauge = triggerErrorsCounter, "Trigger error count", "count",     0,   15000,     0,    0,    6000,  6000,   0,   0
   recentErrorCode0Gauge = recentErrorCode0, "Error#1", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode1Gauge = recentErrorCode1, "Error#2", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode2Gauge = recentErrorCode2, "Error#3", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode3Gauge = recentErrorCode3, "Error#4", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode4Gauge = recentErrorCode4, "Error#5", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode5Gauge = recentErrorCode5, "Error#6", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode6Gauge = recentErrorCode6, "Error#7", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   recentErrorCode7Gauge = recentErrorCode7, "Error#8", "",     0,  18000,     0,    0,   18000, 18000,   0,   0
   firmwareVersionGauge  = firmwareVersion , "ECU Software Version", "%",     0,   100,     0,    0,    100,  100,   0,   0
   timeSecondsGauge     =   timeSeconds, "Uptime", "sec",     0,   100,     0,    0,    100,  100,   0,   0

gaugeCategory = Debug  
   debugFloatField1Gauge = debugFloatField1, @@GAUGE_NAME_DEBUG_F1@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField2Gauge = debugFloatField2, @@GAUGE_NAME_DEBUG_F2@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField3Gauge = debugFloatField3, @@GAUGE_NAME_DEBUG_F3@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField4Gauge = debugFloatField4, @@GAUGE_NAME_DEBUG_F4@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField5Gauge = debugFloatField5, @@GAUGE_NAME_DEBUG_F5@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugFloatField6Gauge = debugFloatField6, @@GAUGE_NAME_DEBUG_F6@@, "%",     -100,   100,     0,    0,    100,  100,   4,   4
   debugFloatField7Gauge = debugFloatField7, @@GAUGE_NAME_DEBUG_F7@@, "%",     0,   100,     0,    0,    100,  100,   4,   4
   debugIntField1Gauge = debugIntField1, "debug i1: pParam", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField2Gauge = debugIntField2, "debug i2: offset", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField3Gauge = debugIntField3, "debug i3", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField4Gauge = debugIntField4, "debug i4", "%",     0,   100,     0,    0,    100,  100,   0,   0
   debugIntField5Gauge = debugIntField5, "debug i5", "%",     0,   100,     0,    0,    100,  100,   0,   0


gaugeCategory = Sensors - Basic
   RPMGauge        = RPMValue,           "RPM - engine speed",       "RPM",       0,   15000,     200,    500,    6000,  6000,   0,   0
#if CELSIUS
   CLTGauge          = coolant,       "Coolant temp",        "deg C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   CLTGauge          = coolant,       "Coolant temp",        "deg F",      -40,    285,       5,     35,     205,   230,   1,   1
#endif
#if CELSIUS
   IATGauge          = intake,     "Intake air temp",        "deg C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   IATGauge          = intake,     "Intake air temp",        "deg F",      -40,    285,       5,     35,     205,   230,  1,   1
#endif
   afr1Gauge         = AFRValue, "Air fuel ratio",          "",       10,   19.4,      12,     13,      15,    16,   2,   2
   MAFGauge			 = MAFValue,          "Mass air flow",         "v",        0,      5,       0,      1,       3,     4,   1,   1
   VBattGauge        = VBatt,      "Battery voltage",         "V",        8,     21,       9,     10,      17,    19,   1,   1
   MAPGauge     	 = MAPValue,               "MAP",       "kPa",        0,    300,      10,     10,     200,   200,   0,   0	
   massAirFlowValueGa = massAirFlowValue,"Mass air flow",       "kg/hr",        0,     50,    -999,   -999,     999,   999,   1,   1


gaugeCategory = Sensors - Extra 1
   VSSGauge          = vehicleSpeedKph,     "Vehicle speed",         "kmh",        0,    200,       0,      1,       3,     4,   1,   1
   accelerationXGauge = accelerationX,       @@GAUGE_NAME_ACCEL_X@@,      "acc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1
   accelerationYGauge = accelerationY,       @@GAUGE_NAME_ACCEL_Y@@,      "acc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1
   atmPresCGauge     = baroPressure,          "Barometric pressure",       "kPa",        0,   1024,       0,      0,       0,     0,   0,   0
   vvtPositionGauge = vvtPosition, "VVT position", "deg",     0,   100,     0,    0,    720,  720,   0,   0
   internalMcuTemperatureGauge = internalMcuTemperature, @@GAUGE_NAME_ECU_TEMPERATURE@@, "C",     0,   100,     0,    0,    75,  100,   0,   0
   OilPressGauge   	 = oilPressure,   "Oil Pressure",       "kPa",        0,    750,      35,     75,     550,   700,   0,   0	
   idleAirValvePositionGauge = idleAirValvePosition, "Idle position", "%",     0,   100,     0,    0,    100,  100,   1,   1

gaugeCategory = Ignition
   ignadvGauge = ignitionAdvance,       "Ignition timing",   "degrees",     -100,    100,    -999,   -999,     999,   999,   1, 1
   dwellGauge        = sparkDwellValue,           "Dwell",      "mSec",        0,     10,     0.5,    1.0,     6.0,   8.0,   1, 1
   coilDutyCycleGauge = coilDutyCycle,       @@GAUGE_NAME_DWELL_DUTY@@,      "perc",        -11,   11,     1.0,    1.2,      100,    100,   3, 1

gaugeCategory = Acceleration Enrichment
   engineLoadDeltaGauge = engineLoadDelta,"AE: load change","value",      0,    120,      10,     10,     100,   100,   1,   1
   engineLoadAccelExtraGauge = engineLoadAccelExtra,"AE: load extra","value",      0,    120,      10,     10,     100,   100,   1,   1
   deltaTpsGauge     = deltaTps,                "AE: TPS change",            "",        0,    120,      10,     10,     100,   100,   1,   1
   tpsAccelFuelGauge = tpsAccelFuel,"AE: TPS enrich",             "ms",        0,    120,      10,     10,     100,   100,   1,   1
   wallFuelAmountGauge = wallFuelAmount, "AE: wall amount", "ms",     0,   100,     0,    0,    100,  100,   0,   0
   wallFuelCorrectionGauge = wallFuelCorrection, "AE: wall correction extra", "ms",     0,   100,     0,    0,    100,  100,   0,   0

gaugeCategory = Fueling
   ;Name               Var            Title                 Units        Lo      Hi      LoD    LoW       HiW   HiD    vd  ld
#if CELSIUS
   tChargeGauge          = tCharge,     @@GAUGE_NAME_FUEL_CHARGE_TEMP@@,        "deg C",      -40,    140,     -15,      1,      95,   110,   1,   1
#else
   tChargeGauge          = tCharge,     @@GAUGE_NAME_FUEL_CHARGE_TEMP@@,        "deg F",      -40,    285,       5,     35,     205,   230,  1,   1
#endif
   baroCorrectionGauge  = baroCorrection,"Fuel: Barometric pressure correction",           "ratio",        0.5,    1.5,      0.6,     0.7,     1.3,   1.4,   1,   1
   crankingFuelGauge = crankingFuelMs,   @@GAUGE_NAME_FUEL_CRANKING@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   iatCorrectionGauge = iatCorrection, @@GAUGE_NAME_FUEL_IAT_CORR@@, "mult",     0,   3,     0,    0,    3,  3,   2,   2
   cltCorrectionGauge = cltCorrection, @@GAUGE_NAME_FUEL_CLT_CORR@@, "mult",     0,   3,     0,    0,    3,  3,   2,   2
   injectorDutyCycleGauge=injectorDutyCycle, @@GAUGE_NAME_FUEL_INJ_DUTY@@,"%",      0,    120,      10,     10,     100,   100,   1,   1
   actualLastInjectionGauge   = actualLastInjection,     @@GAUGE_NAME_FUEL_LAST_INJECTION@@, "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   veValueGauge      = veValue,                 "fuel: VE",            "",        0,    120,      10,     10,     100,   100,   1,   1
   
   injectorLagMsGauge = injectorLagMs,       @@GAUGE_NAME_INJECTOR_LAG@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   fuelRunningGauge     = fuelRunning,       @@GAUGE_NAME_FUEL_RUNNING@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   baseFuelGauge     = baseFuel,       @@GAUGE_NAME_FUEL_BASE@@,      "mSec",        0,   25.5,     1.0,    1.2,      20,    25,   3, 1
   fuelPidCorrectionGauge = fuelPidCorrection,       @@GAUGE_NAME_FUEL_PID_CORR@@,      "mSec",        -11,   11,     1.0,    1.2,      20,    25,   3, 1

gaugeCategory = Throttle Body (incl. ETB)
   pedalPositionGauge = pedalPosition, "Throttle pedal position",        "%",    0,    120,      0,     0,     100,   100,   1,   1
   tpsADCGauge       = tpsADC,           "tps1 ADC",       "ADC",        0,   1024,       0,      0,       0,     0,   0,   0
   TPSGauge			 = TPSValue,      "Throttle position",         "%",        0,    100,       0,      0,     100,   100,   1,   1

   etbTargetGauge     = etbTarget,     "ETB position target", "%",    0,    100,    0,     0,     100,   100,   1,   1
   etbErrorGauge      = etb1Error,     "ETB position error",  "%",    -20,  20,    -10,   -5,    5,    10,  2, 0
   etbDutyCycleGauge  = etb1DutyCycle, "ETB duty cycle",                 "%",    -100, 100,   -75,   -50,   50,   75,  0, 0


[WueAnalyze]
    
;                    wueCurveName, afrTempCompensationCurve, lambdaTargetTableName, lambdaChannel, coolantTempChannel, egoCorrectionChannel, wueChannel, activeCondition
     wueAnalyzeMap = wueAnalyzer_warmup_curve, wueAfrTargetOffsetCurve, afrTableTbl, AFRValue, coolant, cltCorrection, egoCorrection

     lambdaTargetTables = afrTableTbl, afrTSCustom

     wuePercentOffset = 0 ; for working with 0 based enrichment set to 100
     option = disableLiveUpdates
     option = burnOnSend

;     filter = std_DeadLambda ; Auto build

     filter = decelFilterMap,"After Start Enrich", engine,         &     , 4 ,       , false
     filter = accelFilterTp, "TP Accel Enrich"   , engine,         &     , 16,       , false
     filter = decelFilterTp, "TP Decel Enrich"   , engine,         &     , 32,       , false
     filter = accelFilterMap,"MAP Accel Enrich"  , engine,         &     , 64,       , false
     filter = decelFilterMap,"MAP Decel Enrich"  , engine,         &     , 128,      , false
     ; this works, just another way to skin a cat
     ;filter = decelFilter, "Decel Flag" , tpsaccden,         >       , 0,        , false
     filter = overrunFilter, "Overrun"    , pulseWidth1,  =       , 0,            , false
     filter = highThrottle, "High Throttle"    , throttle,  >       , 15,         , true
     filter = lowRpm,       "Low RPM"    ,       rpm,       <       , 300,        , false
     filter = std_Custom ; Standard Custom Expression Filter.

   
[FrontPage]
   ; Gauges are numbered left to right, top to bottom.
   ;
   ;    1  2  3  4
   ;    5  6  7  8

   ; currently a minimum of 6 gauges must be on the dash, this appears to be an old not needed limitation. next release 1 will work.
   gauge1 = RPMGauge
   gauge2 = CLTGauge
   gauge3 = TPSGauge
   gauge4 = MAFGauge
   gauge5 = afr1Gauge
   gauge6 = VBattGauge
   gauge7 = dwellGauge
   gauge8 = ignadvGauge
   


;         =   expression,            off-label,            on-label,            off-bg, off-fg, on-bg, on-fg
	; important status
    indicator = { ind_hasFatalError }, "",   "FATAL ERROR",   green, black, red,   black
    indicator = { firmwareTsVersion == fileVersion }, "WRONG VERSION",   "version",   red, black, green,   black
    indicator = { ind_isWarnNow }, "",   "warn",   green, black, red,   black
    indicator = { ind_check_engine }, "ok",      "Check engine",       green,  black,  red, black
    indicator = { isIgnitionEnabledIndicator}, "no ignition",   "ignition",   red, black, green,   black
    indicator = { ind_injection_enabled}, "no injection",   "injection",   red, black, green,   black
    indicator = { ind_isTriggerError}, "ok",      "trg err",       green,  black,  red, black
    

	; minor info	
    indicator = { ind_fan}, "no fan",   "fan",   white, black, green,   black
    indicator = { isCylinderCleanupActivated}, "no cyl cleanup",   "cyl cleanup",   white, black, green,   black    
    indicator = { needBurn }, "config ok",  "unsaved changes",   white, black, yellow,   black
    indicator = { hasSdCard}, "no SD",   "with SD",   white, black, green,   black
    indicator = { ind_fuel_pump}, "no pump",   "pump",   white, black, green,   black
    indicator = { clutchUpState }, "clutch",   "cltch Up",   white, black, red,   black
    indicator = { clutchDownState }, "clutch",   "cltch Down",   white, black, yellow,   black
    indicator = { brakePedalIndicator }, "brake",   "brake down",   white, black, red,   black
    indicator = { acSwitchIndicator }, "AC on",   "AC off",   yellow, black, white,   black
    
    ; error codes
    indicator = { ind_tps_error}, "tps",   "tps error",   white, black, red,   black
    indicator = { ind_clt_error}, "clt",   "clt error",   white, black, red,   black
    indicator = { ind_iat_error}, "iat",   "iat error",   white, black, red,   black
    indicator = { ind_map_error}, "map",   "map error",   white, black, red,   black

    indicator = { knockEverIndicator }, "",   "Knock recently",   white, black, red,   black
    indicator = { knockNowIndicator }, "no knock",   "Knock NOW",   white, black, red,   black
   

[Datalog]
   ;       Channel          Label          Type    Format
   entry = time,            "Time",        float,  "%.3f"
   entry = RPMValue,        "RPM",         int,    "%d"
   entry = firmwareVersion, @@GAUGE_NAME_VERSION@@,     int,    "%d"
   entry = coolant,         "CLT",         float,  "%.2f"
   entry = intake,          "IAT",         float,  "%.2f"
   entry = oilPressure,		"Oil Press",   float,  "%.1f"
   entry = TPSValue,             "TPS",         float,  "%.2f"
   entry = MAFValue,             "MAF",         float,  "%.2f"
   entry = MAPValue,        "MAP",         float,  "%.1f"
   entry = AFRValue,       @@GAUGE_NAME_AFR@@,         float,  "%.2f"
   entry = VBatt,           @@GAUGE_NAME_VBAT@@,       float,  "%.2f"
   entry = engineLoad,	    @@GAUGE_NAME_ENGINE_LOAD@@, 	   float,  "%.1f"
   entry = ignitionAdvance,	@@GAUGE_NAME_TIMING_ADVANCE@@,	   float,  "%.2f"
   entry = knockLevel,	    @@GAUGE_NAME_KNOCK_LEVEL@@, 	   float,  "%.2f"
   entry = knockCount,		@@GAUGE_NAME_KNOCK_COUNTER@@,	   int,    "%d"
   entry = vehicleSpeedKph,	@@GAUGE_NAME_VVS@@,	   float,  "%.2f"
   entry = speedToRpmRatio, "s2rpm",	   float,  "%.3f"
   entry = rpmAcceleration, "dRPM",        float,  "%.3f"
   entry = massAirFlowValue,"air flow",    float,  "%.3f"
   entry = chargeAirMass,   "air mass",    float,  "%.3f"
   entry = pedalPosition,   "pedal",       float,  "%.3f"
   entry = triggerErrorsCounter, "trg err",int,    "%d"
   entry = idleAirValvePosition, @@GAUGE_NAME_IAC@@, float,  "%.3f"


   entry = injectorLagMs,   @@GAUGE_NAME_INJECTOR_LAG@@, float,  "%.3f"
   entry = fuelRunning,     @@GAUGE_NAME_FUEL_RUNNING@@, float,  "%.3f"
   entry = actualLastInjection,     @@GAUGE_NAME_FUEL_LAST_INJECTION@@, float,  "%.3f"
   entry = baseFuel,	    @@GAUGE_NAME_FUEL_BASE@@,  float,  "%.2f"
   entry = fuelPidCorrection,@@GAUGE_NAME_FUEL_PID_CORR@@,  float,  "%.2f"
   entry = veValue,         @@GAUGE_NAME_FUEL_VE@@,    float,  "%.3f"
   entry = injectorDutyCycle,@@GAUGE_NAME_FUEL_INJ_DUTY@@,float,"%.3f"
   entry = coilDutyCycle,	@@GAUGE_NAME_DWELL_DUTY@@,	float,"%.3f"
   entry = currentTargetAfr,@@GAUGE_NAME_TARGET_AFR@@,	float,"%.3f"

   entry = accelerationX,	@@GAUGE_NAME_ACCEL_X@@,	float,"%.2f"
   entry = accelerationY,	@@GAUGE_NAME_ACCEL_Y@@,	float,"%.2f"
   entry = egt1,	        "EGT1",	float,"%.1f"
   entry = egt2,	        "EGT2",	float,"%.1f"
   entry = egt3,	        "EGT3",	float,"%.1f"
   entry = egt4,	        "EGT4",	float,"%.1f"
   entry = egt5,	        "EGT5",	float,"%.1f"
   entry = egt6,	        "EGT6",	float,"%.1f"
   entry = egt7,	        "EGT7",	float,"%.1f"
   entry = egt8,	        "EGT8",	float,"%.1f"

   entry = engineLoadAccelExtra, @@GAUGE_NAME_FUEL_EL_EXTRA@@,float,  "%.3f"
   entry = engineLoadDelta, "fuel: load change",float,  "%.3f"

   entry = deltaTps,		@@GAUGE_NAME_FUEL_TPS_ROC@@,float,  "%.3f"
   entry = tpsAccelFuel,    @@GAUGE_NAME_FUEL_TPS_EXTRA@@,    float,  "%.3f"

   entry = wallFuelCorrection,@@GAUGE_NAME_FUEL_WALL_CORRECTION@@,	float,   "%.3f"
   entry = wallFuelAmount, @@GAUGE_NAME_FUEL_WALL_AMOUNT@@,	float,   "%.3f"
   
   entry = baroCorrection,   "baroCorrection",float,"%.3f"
   entry = iatCorrection,   @@GAUGE_NAME_FUEL_IAT_CORR@@,	float,   "%.3f"
   entry = cltCorrection,	@@GAUGE_NAME_FUEL_CLT_CORR@@, float,"%.3f"

   entry = sparkDwellValue,	@@GAUGE_COIL_DWELL_TIME@@, float,"%.3f"
   entry = vvtPosition, @@GAUGE_NAME_VVT@@, float,"%.2f"
   entry = injectionOffset, "injOffset"  , float, "%.2F"

; is there a way to log parameter?   entry = debugMode,   "debugMode",int,"%d"
; Alternator_PID: alternator duty cycle
; DBG_TPS_ACCEL: from TPS 
   entry = debugFloatField1,   @@GAUGE_NAME_DEBUG_F1@@,float,"%.4f"

; Alternator_PID: current integration term
; DBG_TPS_ACCEL: to TPS
   entry = debugFloatField2,   @@GAUGE_NAME_DEBUG_F2@@,float,"%.4f"
   
; Alternator_PID: previous error
; DBG_TPS_ACCEL: tps<>tps table value
   entry = debugFloatField3,   @@GAUGE_NAME_DEBUG_F3@@,float,"%.4f"
   
; Alternator_PID: I setting
; DBG_TPS_ACCEL: extra fuel   
   entry = debugFloatField4,   @@GAUGE_NAME_DEBUG_F4@@,float,"%.4f"

; Alternator_PID: D setting
   entry = debugFloatField5,   @@GAUGE_NAME_DEBUG_F5@@,float,"%.4f"

; Alternator_PID: dTerm
   entry = debugFloatField6,   @@GAUGE_NAME_DEBUG_F6@@,float,"%.4f"
   
   entry = debugFloatField7,   @@GAUGE_NAME_DEBUG_F7@@,float,"%.4f"


; Alternator_PID: P setting
   entry = debugIntField1,   @@GAUGE_NAME_DEBUG_I1@@,int,"%d"

; Alternator_PID: offset setting
   entry = debugIntField2,   @@GAUGE_NAME_DEBUG_I2@@,int,"%d"
   
; Alternator_PID: PID reset counter   
   entry = debugIntField3,   @@GAUGE_NAME_DEBUG_I3@@,int,"%d"

   entry = debugIntField4,   @@GAUGE_NAME_DEBUG_I4@@,int,"%d"

   entry = debugIntField5,   @@GAUGE_NAME_DEBUG_I5@@,int,"%d"
   
      
   entry = engineMode,   "Engine Mode",int,"%d"
   entry = warningCounter,   @@GAUGE_NAME_WARNING_COUNTER@@,int,"%d"
   entry = lastErrorCode,   @@GAUGE_NAME_WARNING_LAST@@,int,"%d"
   entry = recentErrorCode0,   "error 0",int,"%d"
   entry = recentErrorCode1,   "error 1",int,"%d"
   entry = recentErrorCode2,   "error 2",int,"%d"
   entry = recentErrorCode3,   "error 3",int,"%d"
   entry = recentErrorCode4,   "error 4",int,"%d"
   entry = recentErrorCode5,   "error 5",int,"%d"
   entry = recentErrorCode6,   "error 6",int,"%d"
   entry = recentErrorCode7,   "error 7",int,"%d"
   entry = internalMcuTemperature,   @@GAUGE_NAME_CPU_TEMP@@,float,"%.2f"
   
   entry = tCharge, "tCharge",float,"%.3f"
   
   entry = clutchUpState,   @@INDICATOR_NAME_CLUTCH_UP@@,int,"%d"
   entry = clutchDownState,   @@INDICATOR_NAME_CLUTCH_DOWN@@,int,"%d"
   entry = brakePedalIndicator,   @@INDICATOR_NAME_BRAKE_DOWN@@,int,"%d"
   entry = acSwitchIndicator,   "AC switch",int,"%d"
   entry = ind_fan, "radiator fan",int,"%d"

; Electronic throttle body
   entry = etb1Error,      "ETB Error", float, "%.3f"
   entry = etb1DutyCycle,  "ETB Duty", float, "%.3f"
   entry = etbTarget,      "ETB Target", float, "%.3f"
   
   
;     tpsADC          = U16,    "ADC",
;     alignmet        = U16,    "al",
;     atmPres         = F32,    "pres",
;	  crankingFuel    = F32,    "ms",
;     tCharge         = F32,    "T",
;     sparkDwell      = F32,    "MAP",
;     warmUpEnrich    = F32,    "%",

[Menu]

menuDialog = main
	menu = "&Base &Engine"
		subMenu = engineChars,				"Base engine"
		subMenu = triggerConfiguration,		"Trigger"
		subMenu = std_separator
		subMenu = energySystems,			"Battery and alternator"
		subMenu = std_separator
		
		# Digital outputs
		subMenu = mainRelay,				"Main relay"
		subMenu = fuelPump,					"Fuel pump"
		subMenu = fanSetting,				"Fan"
		subMenu = tachSettings,				"Tachometer"
		subMenu = malfunction,				"Check engine light"
		subMenu = statusLeds,				"Status LEDs"

	menu = "Fuel"
		# basic
		subMenu = injectionSettings,		"Injection settings"
		subMenu = injectionDeadTime,		"Injector dead time", 0, {isInjectionEnabled == 1}
		subMenu = std_separator

		# Targets & closed loop
		subMenu = afrTableTbl,				"Target AFR", 0, {isInjectionEnabled == 1 && fuelAlgorithm == LM_SPEED_DENSITY}
		subMenu = fuelClosedLoopDialog, 	"Closed loop correction", 0, {isInjectionEnabled == 1}
		subMenu = coastingFuelCutControl, 	"Deceleration fuel cutoff (DFCO)", 0, {isInjectionEnabled == 1}
		subMenu = std_separator

		# Fuel table/VE
		subMenu = fuelTableDialog,			"Fuel table", 0, {isInjectionEnabled == 1 && fuelAlgorithm != LM_SPEED_DENSITY}
		subMenu = veTableDialog,			"VE", 0, {isInjectionEnabled == 1 && fuelAlgorithm == LM_SPEED_DENSITY}
		subMenu = injPhaseTableTbl,         "Injection phase", 0, {isInjectionEnabled == 1}
		subMenu = std_separator

		# Corrections
		subMenu = cltFuelCorrCurve,			"CLT multiplier", 0, {isInjectionEnabled == 1 && useWarmupPidAfr == 0}
		subMenu = iatFuelCorrCurve,			"IAT multiplier", 0, {isInjectionEnabled == 1}
		subMenu = baroCorrTbl,				"Baro multiplier", 0, {isInjectionEnabled == 1 && fuelAlgorithm == LM_SPEED_DENSITY}
		subMenu = tChargeSettings,			"tCharge settings", 0, {isInjectionEnabled == 1}
		subMenu = std_separator

		# Accel enrichment
		subMenu = AccelEnrich,				"Accel/decel enrichment/enleanment", 0, {isInjectionEnabled == 1}
		subMenu = tpsTpsAccelTbl, 			"TPS/TPS acceleration extra fuel", 0, {isInjectionEnabled == 1}
		subMenu = mapAccelTaper,			"Engine load AE taper", 0, {isInjectionEnabled == 1}


	menu = "Ignition"
		subMenu = ignitionSettings,			"Ignition settings"
        subMenu = std_separator

		subMenu = dwellSettings,			"Dwell", 0, {isIgnitionEnabled == 1}
		subMenu = ignitionCylExtra,			"Ignition cylinder trim", 0, {isIgnitionEnabled == 1}
		subMenu = std_separator

		subMenu = ignitionTableTbl,			"Ignition advance", 0, {isIgnitionEnabled == 1 && useTPSAdvanceTable == 0}
		subMenu = ignitionTpsTableTbl,		"Ignition advance (TPS)", 0, {isIgnitionEnabled == 1 && useTPSAdvanceTable == 1}
		subMenu = std_separator

		# corrections
		subMenu = cltTimingCorrCurve,		"CLT correction", 0, {isIgnitionEnabled == 1}
		subMenu = ignitionIatCorrTableTbl,	"IAT correction", 0, {isIgnitionEnabled == 1}
		
	menu = "&Cranking"
		subMenu = crankingDialog,			"Cranking settings"
		subMenu = std_separator

		subMenu = crankingCltCurve,			"Fuel CLT multiplier"
		subMenu = crankingDurationCurve,	"Fuel duration multiplier"	
		subMenu = crankingTpsCurve,			"Fuel TPS multiplier"
		subMenu = std_separator

		subMenu = crankingAdvanceCurve,		"Ignition advance", 0, {useSeparateAdvanceForCranking == 1}
		subMenu = std_separator

		subMenu = cltCrankingCurve,			"IAC multiplier", 0, {overrideCrankingIacSetting == 1}	
		
	menu = "&Idle"
		subMenu = idleSettings,				"Idle settings"
		subMenu = idlehw,					"Idle hardware"
		subMenu = std_separator	
		subMenu = cltIdleRPMCurve,			"Target RPM", 0, {idleMode == 0}
		subMenu = idleVeCurve,              "VE", 0, {useSeparateVeForIdle == 1}
		subMenu = idleAdvanceCurve,			"Ignition advance", 0, {useSeparateAdvanceForIdle == 1}
		subMenu = std_separator
		subMenu = idleTimingPidCorrDialog,	"Closed-loop idle timing"
		subMenu = cltIdleCurve,				"CLT multiplier"
		subMenu = iacCoastingCurve,			"Coasting IAC Position for Auto-Idle", 0, {useIacTableForCoasting == 1}

	menu = "&FSIO" 
		subMenu = fsioInputsDialog,        	"FSIO inputs"
		subMenu = auxPidDialog,				"Aux PID"
		subMenu = fsioOutputsDialog,        "FSIO outputs"
		subMenu = fsioTable1Tbl,			"FSIO Table #1"
		subMenu = fsioTable2Tbl,			"FSIO Table #2"
		subMenu = fsioTable3Tbl,			"FSIO Table #3"
		subMenu = fsioTable4Tbl,			"FSIO Table #4"
		subMenu = fsioFormulas,				"FSIO Formulas"
		subMenu = fsioCurve1,			    "FSIO Curve #1"
		subMenu = fsioCurve2,			    "FSIO Curve #2"
		subMenu = fsioCurve3,			    "FSIO Curve #3"
		subMenu = fsioCurve4,			    "FSIO Curve #4"

	menu = "&Sensors"
		# Base analog input settings
		subMenu = triggerInputs,			"Trigger inputs"
		subMenu = otherSensorInputs,		"Misc sensors"
		subMenu = analogInputSettings,		"Analog input settings"
		subMenu = std_separator

		# Thermistors
		subMenu = cltSensor,				"CLT sensor"
		subMenu = iatSensor,				"IAT sensor"
		subMenu = auxTempSensor1Sensor,		"AuxTemp1 sensor"
		subMenu = auxTempSensor2Sensor,		"AuxTemp2 sensor"
		subMenu = std_separator

		# TPS/pedal
		subMenu = tpsSensor,				"TPS"
		subMenu = pedalSensor,				"Accelerator pedal"
		subMenu = std_separator

		# MAP/Baro
		subMenu = mapSettings,				"MAP sensor"
		subMenu = mapCurves,				"MAP sampling"
		subMenu = baroSettings,				"Baro sensor"
		subMenu = std_separator

		# MAF
		subMenu = mafSettings,				"MAF sensor"
		subMenu = mafDecodingCurve,			"MAF transfer function", 0, {mafAdcChannel != 16}
		subMenu = std_separator

		# O2 sensor(s)
		subMenu = egoSettings,				"EGO sensor"
		subMenu = narrowToWideOxygenCurve,	"Narrow to Wideband approximation"
		subMenu = cj125Function,			"CJ125 settings (wbo decoder)" @@if_ts_show_cj125
		subMenu = std_separator

		# Misc sensors
		subMenu = speedSensor,				"Vehicle speed sensor"
		subMenu = oilPressureSensor,		"Oil pressure"
		subMenu = egtInputs,				"EGT" @@if_ts_show_egt

	menu = "&Controller"
		subMenu = ecuStimulator,			"ECU stimulator"
		subMenu = ioTest,					"Bench test"
		subMenu = engineTypeDialog,			"Popular vehicles"
		subMenu = std_separator
		
		subMenu = lcdScreen,				"LCD" @@if_ts_show_lcd
		subMenu = joystickPanel,			"Joystick" @@if_ts_show_joystick
		subMenu = spiFunction,				"SPI"
		subMenu = monitoringSettings,		"rusEfi console"
		subMenu = std_separator
		
		subMenu = connection,            	"Connection"
		subMenu = allPins1,					"Full pinout 1/2" @@if_ts_show_full_pinout
		subMenu = allPins2,					"Full pinout 2/2" @@if_ts_show_full_pinout
		subMenu = std_separator


		# EXPERIMENTAL FEATURES
		subMenu = parkingLot,				"Experimental/Broken"
		subMenu = warmupTargetAfrCurve,		"Warmup fuel auto correction AFR target"
		subMenu = smLaunchControl,			"Launch control"
		subMenu = std_separator
		
		subMenu = hipFunction,				"HIP9011 settings (knock sensor) (alpha version)" @@if_ts_show_hip9011
		subMenu = std_separator

		subMenu = etbDialog,				"Electronic throttle body (beta version)" @@if_ts_show_etb
		subMenu = etbTpsBiasCurve,			"Electronic throttle body bias curve" @@if_ts_show_etb
		subMenu = pedalToTpsTbl,			"Electronic Pedal Map" @@if_ts_show_etb


[ControllerCommands]
; commandName    = command1, command2, commandn...
; command in standard ini format, a command name can be assigned to 1 to n commands that will be executed in order.
;         This does not include any resultant protocol envelope data, only the response data itself.

; WARNING!! These commands bypass TunerStudio's normal memory synchronization. If these commands
; alter mapped settings (Constant) memory in the controller, TunerStudio will have an out of sync condition 
; and may create error messages.
; It is expected that these commands would not typically alter any ram mapped to a Constant.

;
; see TS_IO_TEST_COMMAND in firmware code
;

cmd_test_spk1  = "w\x00\x12\x00\x01"
cmd_test_spk2  = "w\x00\x12\x00\x02"
cmd_test_spk3  = "w\x00\x12\x00\x03"
cmd_test_spk4  = "w\x00\x12\x00\x04"
cmd_test_spk5  = "w\x00\x12\x00\x05"
cmd_test_spk6  = "w\x00\x12\x00\x06"
cmd_test_spk7  = "w\x00\x12\x00\x07"
cmd_test_spk8  = "w\x00\x12\x00\x08"
cmd_test_spk9  = "w\x00\x12\x00\x09"
cmd_test_spk10 = "w\x00\x12\x00\x0a"
cmd_test_spk11 = "w\x00\x12\x00\x0b"
cmd_test_spk12 = "w\x00\x12\x00\x0c"
cmd_test_spk13 = "w\x00\x12\x00\x0d"
cmd_test_spk14 = "w\x00\x12\x00\x0e"
cmd_test_spk15 = "w\x00\x12\x00\x0f"
cmd_test_spk16 = "w\x00\x12\x00\x10"
		
		
cmd_test_inj1  = "w\x00\x13\x00\x01"
cmd_test_inj2  = "w\x00\x13\x00\x02"
cmd_test_inj3  = "w\x00\x13\x00\x03"
cmd_test_inj4  = "w\x00\x13\x00\x04"
cmd_test_inj5  = "w\x00\x13\x00\x05"
cmd_test_inj6  = "w\x00\x13\x00\x06"
cmd_test_inj7  = "w\x00\x13\x00\x07"
cmd_test_inj8  = "w\x00\x13\x00\x08"
cmd_test_inj9  = "w\x00\x13\x00\x09"
cmd_test_inj10 = "w\x00\x13\x00\x0a"
cmd_test_inj11 = "w\x00\x13\x00\x0b"
cmd_test_inj12 = "w\x00\x13\x00\x0c"
cmd_test_inj13 = "w\x00\x13\x00\x0d"
cmd_test_inj14 = "w\x00\x13\x00\x0e"
cmd_test_inj15 = "w\x00\x13\x00\x0f"
cmd_test_inj16 = "w\x00\x13\x00\x10"
		
cmd_test_fuel_pump           = "w\x00\x14\x00\x01"
cmd_calibrate_tps_1_closed   = "w\x00\x14\x00\x02"
cmd_calibrate_tps_1_wot      = "w\x00\x14\x00\x03"
cmd_calibrate_tps_2_closed   = "w\x00\x14\x00\x04"
cmd_calibrate_tps_2_wot      = "w\x00\x14\x00\x05"
cmd_calibrate_pedal_up       = "w\x00\x14\x00\x06"
cmd_calibrate_pedal_down     = "w\x00\x14\x00\x07"

cmd_test_radiator_fan        = "w\x00\x15\x00\x01"
cmd_test_check_engine_light  = "w\x00\x16\x00\x01"
cmd_test_idle_valve          = "w\x00\x17\x00\x01"
cmd_call_from_pit            = "w\x00\x20\x34\x56"
cmd_stop_engine              = "w\x00\x79\x00\x00"

cmd_reset_controller         = "w\x00\xbb\x00\x00"

; See 'executeTSCommand' in firmware source code
; MIATA_NA6_MAP = 41
cmd_set_engine_type_Miata_NA6_MAP			= "w\x00\x30\x00\x29"
; MIATA_NA6_VAF = 57
cmd_set_engine_type_Miata_NA6_VAF			= "w\x00\x30\x00\x39"
; MAZDA_MIATA_2003 = 47
cmd_set_engine_type_Miata_NA2 				= "w\x00\x30\x00\x2F"
; ETB_BENCH_ENGINE = 58
cmd_set_engine_type_etb_test				= "w\x00\x30\x00\x3A"
; ETB_BENCH_ENGINE = 59
cmd_set_engine_type_8888_test				= "w\x00\x30\x00\x3B"
cmd_set_engine_type_default					= "w\x00\x31\x00\x00"
		
[UserDefined]
	dialog = fuelTableBottomDialog, "", card
		panel = fuelTableMAFTbl, Center, {fuelAlgorithm==LM_PLAIN_MAF}
		panel = fuelTableTPSTbl, Center, {fuelAlgorithm==LM_ALPHA_N}
		panel = fuelTableELTbl, Center

	dialog = fuelTableRight, "", yAxis
	 	topicHelp = "https://rusefi.com/s/fuel"
		displayOnlyField = "Fuel Algorithm",						fuelAlgorithm
		panel = fuelTableBottomDialog, Center
		liveGraph = fuelLive, "Fuel", South
			graphLine = AFRValue
		    graphLine = RPMValue

	dialog = fuelTableGaugesPanel, yAxis
		gauge = TPSGauge
		gauge = MAFGauge
		gauge = MAPGauge

	dialog = fuelTableDialog, "Fuel Table", xAxis
		topicHelp = "fuelHelp"
		panel = fuelTableGaugesPanel
		panel = fuelTableRight

	dialog = tChargeRpmTpsSettings, "RPM+TPS Mode Settings"
	    field = "We use these coefficients to approximate air/fuel charge temperate"
	    field = "based on CLT and IAT, depending on RPM and TPM"
		field = "minRPM minTPS", tChargeMinRpmMinTps
		field = "minRPM maxTPS", tChargeMinRpmMaxTps
		field = "maxRPM minTPS", tChargeMaxRpmMinTps
		field = "maxRPM maxTPS", tChargeMaxRpmMaxTps

	dialog = tChargeGeneralSettings, ""
		field = "tCharge Mode", tChargeMode
		field = "tChange Increment Limit, deg/sec", tChargeAirIncrLimit
		field = "tChange Decrement Limit, deg/sec", tChargeAirDecrLimit
	    field = ""

	dialog = tChargeAirInterpSettings, "Air Interpolation Mode Settings"
		field = "Min tCharge Coeff.", tChargeAirCoefMin
		field = "Max tCharge Coeff.", tChargeAirCoefMax
		field = "Max Air Flow, kg/h", tChargeAirFlowMax
		
	dialog = tChargeSettings, "tCharge Settings"
		panel = tChargeGeneralSettings
		panel = tChargeRpmTpsSettings, { tChargeMode == 0}
		panel = tChargeAirInterpSettings, { tChargeMode == 1}

	dialog = baseInjection, "General"
		field = "Enabled",						isInjectionEnabled
		field = "Mode",							injectionMode, {isInjectionEnabled == 1}
		field = "#Batch injection with individual wiring"
		field = "Two wire batch emulation",				twoWireBatchInjection, {isInjectionEnabled == 1 && injectionMode == 2}
#if tuneByTPS
		field = "Use TPS instead of Load for VE table",	useTPSBasedVeTable, {isInjectionEnabled == 1 && fuelAlgorithm == LM_SPEED_DENSITY}
#else
		field = "#Enabled for TPS-Based 'VE Autotune Mode' in Project Settings"
		field = "Use TPS instead of Load for VE table",	useTPSBasedVeTable, {0}
#endif

	dialog = ignitionOutputs, "Ignition Outputs"
		field = "Ignition Pin Mode",         	        ignitionPinMode, {isIgnitionEnabled == 1}
		field = "Ignition Pin 1",                       ignitionPins1, {isIgnitionEnabled == 1}
		field = "Ignition Pin 2",                       ignitionPins2, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 1) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 2) || (firingOrder == 7) || (firingOrder == 9) || (firingOrder == 11) || (firingOrder == 12)))}
		field = "Ignition Pin 3",                       ignitionPins3, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 2) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 1) || (firingOrder == 3) || (firingOrder == 4) || (firingOrder == 5) || (firingOrder == 9)))}
		field = "Ignition Pin 4",                       ignitionPins4, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 3) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 7) || (firingOrder == 12)))}
		field = "Ignition Pin 5",                       ignitionPins5, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 4) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 4) || (firingOrder == 12)))}
		field = "Ignition Pin 6",                       ignitionPins6, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 5) && (ignitionMode !=2 || twoWireBatchIgnition == 1 )}
		field = "Ignition Pin 7",                       ignitionPins7, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 6) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 11)))}
		field = "Ignition Pin 8",                       ignitionPins8, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 7) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 11)))}
		field = "Ignition Pin 9",                       ignitionPins9, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 8) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 11)))}
		field = "Ignition Pin 10",                      ignitionPins10, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 9) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 11)))}
		field = "Ignition Pin 11",                      ignitionPins11, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 10) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 11)))}
		field = "Ignition Pin 12",                      ignitionPins12, {isIgnitionEnabled == 1 && (ignitionMode != 0 && cylindersCount > 11) && (ignitionMode !=2 || twoWireBatchIgnition == 1 || ((firingOrder == 5) || (firingOrder == 11)))}
		field = "This is useful to have tachometer working"
		field = "   while converting from distributor"
		field = "Dizzy out Pin",         	    	    dizzySparkOutputPin, {isIgnitionEnabled == 1}
		field = "Dizzy out Pin Mode",                   dizzySparkOutputPinMode, {isIgnitionEnabled == 1}

	dialog = ignitionBasic, ""
		field = "Enabled",						isIgnitionEnabled
		field = "Mode",							ignitionMode, {isIgnitionEnabled == 1}
		field = "#Wasted spark with individual coils"
		field = "Two wire wasted",				twoWireBatchIgnition, {isIgnitionEnabled == 1 && ignitionMode == 2}
		field = "Timing Mode",					timingMode, {isIgnitionEnabled == 1}
		field = "Use TPS-based Advance Table",	useTPSAdvanceTable, {isIgnitionEnabled == 1 && fuelAlgorithm == LM_SPEED_DENSITY}
		field = "#Use fixed timing while validating with a timing gun"
		field = "Fixed Timinig",				fixedTiming, {isIgnitionEnabled == 1 && timingMode == 1}

	dialog = ignitionSettings, "", xAxis
		panel = ignitionBasic
		panel = ignitionOutputs

	dialog = baseEngineConfig, "Engine Configuration"
;		field = "Engine Preset",						engineType
		field = "Number of Cylinders",					cylindersCount
		field = "Engine Displacement",         			displacement
		field = "Firing Order",							firingOrder

;			Engine->Trigger configuration
	dialog = triggerConfiguration_settings,	"Settings Trigger"
		field = "!https://rusefi.com/s/trigger"
		field = "Trigger type",							trigger_type
		field = "Operation mode / speed",				operationMode
		field = "With VR sensors only rising edge has reliable position"
		field = "use only rising edge",					useOnlyRisingEdgeForTrigger    
	    field = "!Reminder that 4-stroke cycle is 720 degrees"
	    field = "Trigger Angle Offset",         		globalTriggerAngleOffset
		field = "#Custom Trigger"
		field = "total Tooth Count",					trigger_customTotalToothCount, {trigger_type == 0}
		field = "skipped Tooth Count",					trigger_customSkippedToothCount, {trigger_type == 0}

	dialog = triggerConfiguration_IO,	"Settings I/O"
	    field = "!https://rusefi.com/s/vvt"
	    field = "VVT mode",								vvtMode, {trigger_type != 80}
	    field = "VVT use rise front",					vvtCamSensorUseRise, {trigger_type != 80}
	    field = "VVT position display offset",			vvtOffset
	    field = "VVT display inverted",					vvtDisplayInverted
	    field = "Miata NB2 from (temporary)",			miataNb2VVTRatioFrom
	    field = "Miata NB2 to (temporary)",				miataNb2VVTRatioTo
	    field = "nbVvtIndex",							nbVvtIndex
	    field = "print verbose sync details to console",verboseTriggerSynchDetails
	    field = "Enable noise filtering",				useNoiselessTriggerDecoder, {trigger_type == 8}
	dialog = triggerConfiguration
		panel = triggerConfiguration_settings,	North
		panel = triggerConfiguration_IO,		South

;			Engine->Injection Settings
	dialog = injChars, "Injector Settings",	yAxis
		field = "Injector Flow",			injector_flow, {isInjectionEnabled == 1}

	dialog = injectorOutputSettings, "Injector Outputs",	yAxis
		field = "!ECU reboot needed to apply these settings"
		field = "injection Pin Mode",       			injectionPinMode, {isInjectionEnabled == 1}
		field = "With batched injection without 'Two wire batch emulation'"
		field = "   fill only first count / 2 values"
		field = "Injection Pin 1",						injectionPins1, {isInjectionEnabled == 1}
		field = "Injection Pin 2",						injectionPins2, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 1}
		field = "Injection Pin 3",						injectionPins3, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 2}
		field = "Injection Pin 4",						injectionPins4, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 3}
		field = "Injection Pin 5 ",						injectionPins5, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 4}
		field = "Injection Pin 6 ",						injectionPins6, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 5}
		field = "Injection Pin 7 ",						injectionPins7, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 6}
		field = "Injection Pin 8 ",						injectionPins8, {isInjectionEnabled == 1 && injectionMode != 3 && cylindersCount > 7}
		field = "Injection Pin 9 ",						injectionPins9, {isInjectionEnabled == 1 && cylindersCount > 8}
		field = "Injection Pin 10 ",	    			injectionPins10, {isInjectionEnabled == 1 && cylindersCount > 9}
		field = "Injection Pin 11 ",					injectionPins11, {isInjectionEnabled == 1 && cylindersCount > 10}
		field = "Injection Pin 12 ",					injectionPins12, {isInjectionEnabled == 1 && cylindersCount > 11}	
	
	dialog = injectionBasic, ""
		topicHelp = "fuelHelp"
		panel = baseInjection
		panel = injChars

	dialog = injectionSettings, "", xAxis
        panel = injectionBasic
        panel = injectorOutputSettings

	dialog = injectionDeadTime,	"", yAxis
		panel = injectorsDeadTime,		East

	dialog = ignitionCylExtra, "Ignition Cylinder Extra Timing"
		field = "Extra cyl #1",                       timing_offset_cylinder1
		field = "Extra cyl #2",                       timing_offset_cylinder2, {cylindersCount > 1}
		field = "Extra cyl #3",                       timing_offset_cylinder3, {cylindersCount > 2}
		field = "Extra cyl #4",                       timing_offset_cylinder4, {cylindersCount > 3}
		field = "Extra cyl #5",                       timing_offset_cylinder5, {cylindersCount > 4}
		field = "Extra cyl #6",                       timing_offset_cylinder6, {cylindersCount > 5}
		field = "Extra cyl #7",                       timing_offset_cylinder7, {cylindersCount > 6}
		field = "Extra cyl #8",                       timing_offset_cylinder8, {cylindersCount > 7}
		field = "Extra cyl #9",                       timing_offset_cylinder9, {cylindersCount > 8}
		field = "Extra cyl #10",                       timing_offset_cylinder10, {cylindersCount > 9}
		field = "Extra cyl #11",                       timing_offset_cylinder11, {cylindersCount > 10} 
		field = "Extra cyl #12",                       timing_offset_cylinder12, {cylindersCount > 11}
	
	dialog = dwellSettings, "", yAxis
		panel = dwellCorrection,	Center
		
;			Sensors->AUX1 Thermistor Sensor Setting
	dialog = auxTempSensor1Sensor,	"aux1 Thermistor Settings"
		field = "Input channel",			auxTempSensor1_adcChannel
		field = "Bias resistor",       		auxTempSensor1_bias_resistor, {auxTempSensor1_adcChannel != 16}

		field = "#Here is three pairs of thermistor temperature and resistance."
		field = "#Typical temperatures is -40 deg C, 0 deg C and 100 deg C"
		field = ""
		field = "Lowest temperature",					auxTempSensor1_tempC_1, {auxTempSensor1_adcChannel != 16}
		field = "Resistance @ LT",						auxTempSensor1_resistance_1, {auxTempSensor1_adcChannel != 16}
		field = ""
		field = "Middle temperature",					auxTempSensor1_tempC_2, {auxTempSensor1_adcChannel != 16}
		field = "Resistance @ MT",						auxTempSensor1_resistance_2, {auxTempSensor1_adcChannel != 16}
		field = ""
		field = "Highest temperature",					auxTempSensor1_tempC_3, {auxTempSensor1_adcChannel != 16}
		field = "Resistance @ HT",						auxTempSensor1_resistance_3, {auxTempSensor1_adcChannel != 16}

;			Sensors->AUX2 Thermistor Sensor Setting
	dialog = auxTempSensor2Sensor, "aux2 Thermistor Settings"
		field = "Input channel",						auxTempSensor2_adcChannel
		field = "Bias resistor",						auxTempSensor2_bias_resistor, {auxTempSensor2_adcChannel != 16}

		field = "#Here is three pairs of thermistor temperature and resistance."
		field = "#Typical temperatures is -40 deg C, 0 deg C and 100 deg C"
		field = ""
		field = "Lowest temperature",					auxTempSensor2_tempC_1, {auxTempSensor2_adcChannel != 16}
		field = "Resistance @ LT",						auxTempSensor2_resistance_1, {auxTempSensor2_adcChannel != 16}
		field = ""
		field = "Middle temperature",					auxTempSensor2_tempC_2, {auxTempSensor2_adcChannel != 16}
		field = "Resistance @ MT",						auxTempSensor2_resistance_2, {auxTempSensor2_adcChannel != 16}
		field = ""
		field = "Highest temperature",					auxTempSensor2_tempC_3, {auxTempSensor2_adcChannel != 16}
		field = "Resistance @ HT",						auxTempSensor2_resistance_3, {auxTempSensor2_adcChannel != 16}
	
	dialog = tpsSensor, "TPS"
		field = "!See Tools>Calibrate TPS"
		field = "Throttle1 position sensor",			tps1_1AdcChannel
		field = "Throttle2 position sensor",			tps2_1AdcChannel
		field = "TPS low value detection threshold",	tpsErrorDetectionTooLow, {tps1_1AdcChannel != 16}
		field = "TPS high value detection threshold",	tpsErrorDetectionTooHigh, {tps1_1AdcChannel != 16}

	dialog = pedalSensor, "Accelerator pedal"
		field = "Accelerator position sensor",			throttlePedalPositionAdcChannel
		field = "Up voltage",					throttlePedalUpVoltage
		field = "Down (WOT) voltage",				throttlePedalWOTVoltage

;			Sensor Inputs
	dialog = otherSensorInputs,					"Other Sensor Inputs"
		field = "Fuel level", 						fuelLevelSensor
		field = "Flex fuel",							flexFuelSensor
		field = "Clutch down pin",						clutchDownPin
		field = "Clutch down inverted",					clutchDownPinInverted
		field = "Clutch up pin",						clutchUpPin
		field = "Clutch up inverted",					clutchUpPinInverted
		field = "Brake pedal pin",						brakePedalPin
		field = "A/C switch",							acSwitchAdc

	dialog = triggerInputs,					"Trigger Inputs"
		field = "!ECU reboot needed to apply these settings"
		field = "#Cam is primary if you have cam sensor"
		field = "Primary channel", 						triggerInputPins1
		field = "Invert Primary",						invertPrimaryTriggerSignal
		field = "Secondary channel", 					triggerInputPins2,            { trigger_type != 0 && trigger_type != 8 && trigger_type != 9 && trigger_type != 18 && trigger_type != 20}
		field = "Invert Secondary",						invertSecondaryTriggerSignal, { trigger_type != 0 && trigger_type != 8 && trigger_type != 9 && trigger_type != 18 && trigger_type != 20}
		field = "Cam Sync/VVT input",					camInput
		
	dialog = allPinsSensors, "Sensors"
		field = "CLT ADC input", 						clt_adcChannel
		field = "IAT ADC input", 						iat_adcChannel
		field = "vBatt ADC input", 						vbattAdcChannel
		field = "TPS1 ADC input", 						tps1_1AdcChannel
		field = "TPS2 ADC input", 						tps2_1AdcChannel
		field = "MAF ADC input", 						mafAdcChannel
		field = "AFR ADC input", 						afr_hwChannel
		field = "Baro ADC input", 						baroSensor_hwChannel
		field = "MAP ADC input", 						map_sensor_hwChannel
		field = "FrequencyReportingMapInputPin",		frequencyReportingMapInputPin
		field = "FuelLevelSensor", 						fuelLevelSensor
		field = "Vehicle Speed Input pin",				vehicleSpeedSensorInputPin
		field = "clutchDownPin",						clutchDownPin
		field = "clutchUpPin",							clutchUpPin
		field = "brakePedalPin",						brakePedalPin
		field = "A/C Switch",							acSwitchAdc
		field = "Aux Temperature #1",					auxTempSensor1_adcChannel
		field = "Aux Temperature #2",					auxTempSensor2_adcChannel

	dialog = allPins1_1
		field = mc33816_cs,								mc33816_cs
		field = mc33816_rstb,							mc33816_rstb
		field = high_fuel_pressure_sensor_1,			high_fuel_pressure_sensor_1
		field = high_fuel_pressure_sensor_2,			high_fuel_pressure_sensor_2
		field = mc33816_driven,							mc33816_driven
		field = mc33816spiDevice,						mc33816spiDevice
		field = "Warning Led",							warningLedPin
		field = "Fatal Error Led",						fatalErrorPin
		field = "tle6240_cs",							tle6240_cs
		field = "tle6240 SPI",							tle6240spiDevice
		field = "mc33972_cs",							mc33972_cs
		field = "mc33972 SPI",							mc33972spiDevice
		panel = allPinsSensors
		field = "Throttle pedal Position Channel", 		throttlePedalPositionAdcChannel
		field = "Primary input channel", 				triggerInputPins1
		field = "Secondary channel", 					triggerInputPins2
		field = "Cam Sync/VVT input",					camInput

	dialog = allPins1_2
		field = "Tachometer output Pin",					tachOutputPin
		field = "Dizzy out Pin",         	    	    dizzySparkOutputPin
		field = "O2 heater pin",						o2heaterPin
		field = "Idle Solenoid Pin",					idle_solenoidPin
		field = "Idle Stepper Dir",						idle_stepperDirectionPin
		field = "Idle Stepper Dir Mode",				stepperDirectionPinMode
		field = "Idle Stepper Step",					idle_stepperStepPin
		field = "Idle Stepper Enable",					stepperEnablePin
		field = "Fuel Pump Pin",						fuelPumpPin
		field = "Fuel Pump Pin Mode",         	        fuelPumpPinMode
		field = "ETB#1 Dir #1",							etb1_directionPin1  @@if_ts_show_etb_pins
		field = "ETB#1 Dir #2",							etb1_directionPin2  @@if_ts_show_etb_pins
		field = "ETB#1 Control #1",						etb1_controlPin1    @@if_ts_show_etb_pins	
		field = "ETB#2 Dir #1",							etb2_directionPin1  @@if_ts_show_etb_pins
		field = "ETB#2 Dir #2",							etb2_directionPin2  @@if_ts_show_etb_pins
		field = "ETB#2 Control #1",						etb2_controlPin1    @@if_ts_show_etb_pins
		field = "SD CS Pin",							sdCardCsPin
		field = "Check Engine Pin",						malfunctionIndicatorPin
		field = "Check Engine Pin Mode",				malfunctionIndicatorPinMode
		field = "Aux Pin #1",							auxPidPins1
		field = "Aux Pin #2",							auxPidPins2
		field = "Aux Pin #3",							auxPidPins3
		field = "Aux Pin #4",							auxPidPins4
		field = "test557pin",							test557pin
		field = "Fan Pin",								fanPin
		field = "Fan Pin Mode",							fanPinMode
		field = "Main Relay Pin",  						mainRelayPin
		field = "Main Relay Mode",			         	mainRelayPinMode
		field = "aux valve #1", 						auxValves1
		field = "aux valve #2", 						auxValves2

	dialog = allPins2_1
		field = "Injection Pin 1",						injectionPins1
		field = "Injection Pin 2",						injectionPins2
		field = "Injection Pin 3",						injectionPins3
		field = "Injection Pin 4",						injectionPins4
		field = "Injection Pin 5 ",						injectionPins5
		field = "Injection Pin 6 ",						injectionPins6
		field = "Injection Pin 7 ",						injectionPins7
		field = "Injection Pin 8 ",						injectionPins8
		field = "Injection Pin 9 ",						injectionPins9
		field = "Injection Pin 10 ",	    			injectionPins10
		field = "Injection Pin 11 ",					injectionPins11
		field = "Injection Pin 12 ",					injectionPins12
		field = "FSIO dig inp #1",						fsioDigitalInputs1
		field = "FSIO dig inp #2",						fsioDigitalInputs2
		field = "FSIO dig inp #3",						fsioDigitalInputs3
		field = "FSIO dig inp #4",						fsioDigitalInputs4
		field = "FSIO dig inp #5",						fsioDigitalInputs5
		field = "FSIO dig inp #6",						fsioDigitalInputs6
		field = "FSIO dig inp #7",						fsioDigitalInputs7
		field = "FSIO dig inp #8",						fsioDigitalInputs8
		field = "FSIO dig inp #9",						fsioDigitalInputs9
		field = "FSIO dig inp #10",						fsioDigitalInputs10
		field = "FSIO dig inp #11",						fsioDigitalInputs11
		field = "FSIO dig inp #12",						fsioDigitalInputs12
		field = "FSIO dig inp #13",						fsioDigitalInputs13
		field = "FSIO dig inp #14",						fsioDigitalInputs14
		field = "FSIO dig inp #15",						fsioDigitalInputs15
		field = "FSIO dig inp #16",						fsioDigitalInputs16


	dialog = allPins2_2
		field = "Ignition Pin 1",                       ignitionPins1
		field = "Ignition Pin 2",                       ignitionPins2
		field = "Ignition Pin 3",                       ignitionPins3
		field = "Ignition Pin 4",                       ignitionPins4
		field = "Ignition Pin 5",                       ignitionPins5
		field = "Ignition Pin 6",                       ignitionPins6
		field = "Ignition Pin 7",                       ignitionPins7
		field = "Ignition Pin 8",                       ignitionPins8
		field = "Ignition Pin 9",                       ignitionPins9
		field = "Ignition Pin 10",                      ignitionPins10
		field = "Ignition Pin 11",                      ignitionPins11
		field = "Ignition Pin 12",                      ignitionPins12
		field = "output #1", 							fsioOutputPins1
		field = "output #2", 							fsioOutputPins2
		field = "output #3", 							fsioOutputPins3
		field = "output #4", 							fsioOutputPins4
		field = "output #5", 							fsioOutputPins5
		field = "output #6", 							fsioOutputPins6
		field = "output #7", 							fsioOutputPins7
		field = "output #8", 							fsioOutputPins8
		field = "output #9", 							fsioOutputPins9
		field = "output #10", 							fsioOutputPins10
		field = "output #11", 							fsioOutputPins11
		field = "output #12", 							fsioOutputPins12
		field = "output #13", 							fsioOutputPins13
		field = "output #14", 							fsioOutputPins14
		field = "output #15", 							fsioOutputPins15
		field = "output #16", 							fsioOutputPins16

	dialog = allPins1_3
		field = "FSIO ADC #1",							fsioAdc1
		field = "FSIO ADC #2",							fsioAdc2
		field = "FSIO ADC #3",							fsioAdc3
		field = "FSIO ADC #4",							fsioAdc4
		field = "GPS RX", 								gps_rx_pin @@if_ts_show_gps
		field = "GPS TX", 								gps_tx_pin @@if_ts_show_gps
		field = "CAN RX pin",							canRxPin
		field = "CAN TX pin",							canTxPin
		field = "SPI1 MOSI",							spi1mosiPin, {is_enabled_spi_1 == 1}
		field = "SPI1 MISO",							spi1misoPin, {is_enabled_spi_1 == 1}
		field = "SPI1 SCK",								spi1sckPin, {is_enabled_spi_1 == 1}
		field = "SPI2 MOSI",							spi2mosiPin, {is_enabled_spi_2 == 1}
		field = "SPI2 MISO",							spi2misoPin, {is_enabled_spi_2 == 1}
		field = "SPI2 SCK",								spi2sckPin, {is_enabled_spi_2 == 1}
		field = "SPI3 MOSI",							spi3mosiPin, {is_enabled_spi_3 == 1}
		field = "SPI3 MISO",							spi3misoPin, {is_enabled_spi_3 == 1}
		field = "SPI3 SCK",								spi3sckPin, {is_enabled_spi_3 == 1}
		field = "hip9011CsPin",							hip9011CsPin
		field = "LIS302DLCsPin",						LIS302DLCsPin
		field = "Malfunction Indicator",				malfunctionIndicatorPin
		field = "Saab CDM knock",						cdmInputPin
		field = "comm status light",					communicationLedPin
		field = "running status light",					runningLedPin
		field = "TLE8888 Chip Select",                  tle8888_cs
		field = "TLE8888 CS Mode",                      tle8888_csPinMode
		field = "TLE 8888 spi",                         tle8888spiDevice
		field = "servo#1",								servoOutputPins1
		field = "servo#2",								servoOutputPins2
		field = "servo#3",								servoOutputPins3
		field = "servo#4",								servoOutputPins4
		field = "servo#5",								servoOutputPins5


	dialog = allPins1_1_and_2, "", xAxis
		panel = allPins1_1
		panel = allPins1_2

	dialog = allPins1, "All Pins 1/2", xAxis
		panel = allPins1_1_and_2
		panel = allPins1_3

	dialog = allPins2_1_and_2, "", xAxis
		panel = allPins2_1
		panel = allPins2_2

	dialog = allPins2, "All Pins 2/2", xAxis
		panel = allPins2_1_and_2


;			Sensors->CLT sensor
	dialog = clt_thermistor, "CLT sensor"
		field = "Input channel",						clt_adcChannel
		field = "Bias resistor",						clt_bias_resistor, {clt_adcChannel != 16}

		field = "#Here is three pairs of thermistor temperature and resistance."
		field = "#Typical temperatures is -40 deg C, 0 deg C and 100 deg C"
		field = ""
		field = "Lowest temperature",  					clt_tempC_1, {clt_adcChannel != 16}
		field = "Resistance @ LT",         	   			clt_resistance_1, {clt_adcChannel != 16}
		field = ""
		field = "Middle temperature",    		  	    clt_tempC_2, {clt_adcChannel != 16}
		field = "Resistance @ MT",         	    		clt_resistance_2, {clt_adcChannel != 16}
		field = ""
		field = "Highest temperature",				 	clt_tempC_3, {clt_adcChannel != 16}
		field = "Resistance @ HT",         	    		clt_resistance_3, {clt_adcChannel != 16}
		field = ""
		field = "Linear characteristic",				useLinearCltSensor, {clt_adcChannel != 16}

	dialog = cltSensor, "", xAxis
		panel = clt_thermistor
		gauge = CLTGauge

;			Sensors->IAT sensor
	dialog = iat_thermistor, "IAT sensor"
		field = "Input channel",						iat_adcChannel
		field = "Bias resistor",						iat_bias_resistor, {iat_adcChannel != 16}

		field = "#Here is three pairs of thermistor temperature and resistance."
		field = "#Typical temperatures is -40 deg C, 0 deg C and 100 deg C"
		field = ""
		field = "Lowest temperature",					iat_tempC_1, {iat_adcChannel != 16}
		field = "Resistance @ LT",						iat_resistance_1, {iat_adcChannel != 16}
		field = ""
		field = "Middle temperature",					iat_tempC_2, {iat_adcChannel != 16}
		field = "Resistance @ MT",						iat_resistance_2, {iat_adcChannel != 16}
		field = ""
		field = "Highest temperature",					iat_tempC_3, {iat_adcChannel != 16}
		field = "Resistance @ HT",						iat_resistance_3, {iat_adcChannel != 16}
		field = ""
		field = "Linear characteristic",				useLinearIatSensor, {iat_adcChannel != 16}

	dialog = iatSensor, "", xAxis
		panel = iat_thermistor
		gauge = IATGauge
		
;			Sensors->Oil pressure sensor
	dialog = oilp_settings, "Oil pressure sensor"
		field = "Oil Pressure ADC input",				oilPressure_hwChannel
		field = "low voltage",							oilPressure_v1, {oilPressure_hwChannel != 16}
		field = "low pressure",							oilPressure_value1, {oilPressure_hwChannel != 16}
		field = "high voltage",							oilPressure_v2, {oilPressure_hwChannel != 16}
		field = "high pressure",						oilPressure_value2, {oilPressure_hwChannel != 16}

	dialog = oilPressureSensor, "", xAxis
		panel = oilp_settings
		gauge = OilPressGauge

;			Sensors->MAP sensor
	dialog = mapSensorAnalog, "MAP sensor", yAxis		
		field = "MAP ADC input", 						map_sensor_hwChannel
		field = "MAP type",								map_sensor_type
		field = "MAP value low point",  		        map_sensor_lowValue
		field = "MAP voltage low point", 	 		    mapLowValueVoltage
		field = "MAP value high point",               	map_sensor_highValue
		field = "MAP voltage high value",               mapHighValueVoltage
		
	dialog = mapSensorFreq, "MAP frequency sensor", yAxis
		field = "MAP Freq",								frequencyReportingMapInputPin
		field = "0 kPa freq",							mapFrequency0Kpa
		field = "100 kpa freq",							mapFrequency100Kpa

	dialog = mapCommon, "MAP common settings"
		field = "frequency-based MAP",					hasFrequencyReportingMapSensor
		field = "Low value threshold",					mapErrorDetectionTooLow
		field = "High value threshold",					mapErrorDetectionTooHigh
		field = ""
		field = "Measure Map Only In One Cylinder",		measureMapOnlyInOneCylinder
		field = "Minimum MAP samples",					mapMinBufferLength

	dialog = mapSettings, "", yAxis
		panel = mapCommon
		panel = mapSensorAnalog, {hasFrequencyReportingMapSensor == 0}
		panel = mapSensorFreq, {hasFrequencyReportingMapSensor == 1}
		panel = mapErrorDetection

	dialog = baroSettings, "Baro sensor"
		field = "Baro ADC input",						baroSensor_hwChannel
		field = baroSensor_lowValue,					baroSensor_lowValue, {baroSensor_hwChannel != 16}
		field = baroSensor_highValue,					baroSensor_highValue, {baroSensor_hwChannel != 16}
		field = baroSensor_type,						baroSensor_type, {baroSensor_hwChannel != 16}

	dialog = mapCurves, "MAP sampling", yAxis
		panel = map_samplingAngleCurve
		panel = map_samplingWindowCurve

	dialog = mafSettings, "MAF sensor", yAxis
		field = "MAF ADC input", 						mafAdcChannel

;			Sensors->EGO sensor
	dialog = egoSettings_sensor,	"EGO sensor"
		field = "Type",									afr_type
; todo: only use these values for custom!		
		field = "low voltage", 							afr_v1
		field = "low value", 							afr_value1
		field = "high voltage", 						afr_v2
		field = "high value", 							afr_value2
		field = "Correction",							egoValueShift

	dialog = egoSettings_IO,	"EGO Sensor I/O"
		field = "Input channel", 						afr_hwChannel
		field = "Heater pin",						o2heaterPin

	dialog = egoSettings, "", yAxis
		panel = egoSettings_IO
		panel = egoSettings_sensor,	{afr_hwChannel != 16}

;			Engine->EGT inputs
	dialog = egtInputs, "EGT inputs"
		field = "SPI", 									max31855spiDevice
        field = "CS #1", 								max31855_cs1
        field = "CS #2", 								max31855_cs2
        field = "CS #3", 								max31855_cs3
        field = "CS #4", 								max31855_cs4
        field = "CS #5", 								max31855_cs5
        field = "CS #6", 								max31855_cs6
        field = "CS #7", 								max31855_cs7
        field = "CS #8", 								max31855_cs8

;			Engine->idle Settings	
	dialog = idleSolenoid, "Solenoid"
		field = "Idle Solenoid Pin Mode",   	  	    idle_solenoidPinMode, !useStepperIdle
		field = "Idle Solenoid Pin",					idle_solenoidPin, !useStepperIdle
		field = "Idle Solenoid Frequency",   			idle_solenoidFrequency, !useStepperIdle
	
	dialog = idleStepper, "Stepper"
		field = "Idle Stepper Step Pin",				idle_stepperStepPin, useStepperIdle
		field = "Idle Stepper Dir Pin",					idle_stepperDirectionPin, useStepperIdle
		field = "Idle Stepper Enable Pin",				stepperEnablePin, useStepperIdle
		field = "Idle Stepper Enable Pin Mode",			stepperEnablePinMode, useStepperIdle
		field = "Stepper reaction time",				idleStepperReactionTime, useStepperIdle
		field = "Stepper total steps",					idleStepperTotalSteps, useStepperIdle
		field = "Stepper parking extra steps, %",		stepperParkingExtraSteps, useStepperIdle
		field = "Force parking every restart",			stepperForceParkingEveryRestart, useStepperIdle
		
	dialog = idleHwType, "Idle Valve Hardware",	border
		panel = idleSolenoid,				West
		panel = idleStepper,				East
		
	dialog = idlehw, "", yAxis
	field = "!ECU reboot needed to apply these settings"
		field = "Use Stepper",				useStepperIdle
		panel = idleHwType
		
	dialog = idlePidSettings, "PID IAC Control"	
		field = "#See Idle Target RPM Curve"
		field = "P-factor",								idleRpmPid_pFactor
		field = "I-factor",								idleRpmPid_iFactor
		field = "D-factor",								idleRpmPid_dFactor
		field = "Offset",								idleRpmPid_offset
		field = "Min",									idleRpmPid_minValue
		field = "Max",									idleRpmPid_maxValue
		field = "period",								idleRpmPid_periodMs
		field = "RPM dead zone to deactivate IAC pid",	idlePidRpmDeadZone
		field = "RPM upper limit to deactivate IAC pid",idlePidRpmUpperLimit
		field = "PID Extra for low RPM",				pidExtraForLowRpm
		
		
	dialog = idleSettings, "", yAxis
		field = "Idle IAC control mode",					idleMode
		field = "use ETB for idle",						useETBforIdleControl
		field = "ETB Idle range",						etbIdleThrottleRange, {useETBforIdleControl == 1}
		field = "Use separate Ignition Table for idle",	useSeparateAdvanceForIdle
		field = "Use separate VE Table for idle",		useSeparateVeForIdle
		field = "Use separate IAC Table For Coasting",	useIacTableForCoasting, {idleMode == 0}
		field = idleIncrementalPidCic,					idleIncrementalPidCic
		field = "TPS deactivation threshold",			idlePidDeactivationTpsThreshold
		panel = idlePidSettings, { idleMode == 0}
		field = "Extra IAC if Throttle Pressed",						iacByTpsTaper;
		field = "Detailed status in console",						isVerboseIAC
		field = "#See Warmup idle multiplier"
		slider = "Manual IAC Position",				manIdlePosition, horizontal

	dialog = idleTimingPidCorrDialog, "", yAxis
		field = "!This timing correction mode is Alpha Version"
		field = "Use Auto-PID ignition advance control",	useIdleTimingPidControl
		field = "#See Idle Target RPM Curve"
		field = "P-factor",									idleTimingPid_pFactor, {useIdleTimingPidControl == 1}
		field = "I-factor",									idleTimingPid_iFactor, {useIdleTimingPidControl == 1}
		field = "D-factor",									idleTimingPid_dFactor, {useIdleTimingPidControl == 1}
		field = "Offset",									idleTimingPid_offset, {useIdleTimingPidControl == 1}
		field = "Min Delta",								idleTimingPid_minValue, {useIdleTimingPidControl == 1}
		field = "Max Delta",								idleTimingPid_maxValue, {useIdleTimingPidControl == 1}
		field = "period",									idleTimingPid_periodMs, {useIdleTimingPidControl == 1}
		field = "#See RPM dead zone to deactivate IAC pid"
		field = "RPM working zone for timing pid",			idleTimingPidWorkZone, {useIdleTimingPidControl == 1}
		field = "RPM working zone falloff",					idlePidFalloffDeltaRpm, {useIdleTimingPidControl == 1}
		field = "RPM dead zone to deactivate timing pid",	idleTimingPidDeadZone, {useIdleTimingPidControl == 1}

;			Engine->Fan Settings
	dialog = fanSetting, "Fan Settings"
		field = "Pin",								fanPin
		field = "Pin mode",							fanPinMode
		field = "On temperature",					fanOnTemperature
		field = "Off temperature",					fanOffTemperature

	dialog = fuelPump, "Fuel Pump"
		field = "Pin",						fuelPumpPin
		field = "Pin mode",         	        fuelPumpPinMode
		field = "Prime duration",				startUpFuelPumpDuration

;			Controller->Actuator Outputs
	dialog = mainRelay, "Main relay output"
		field = "Pin",  						mainRelayPin
		field = "Pin mode",			         	mainRelayPinMode

	dialog = statusLeds, "Status LEDs"
		field = "Running status LED",					runningLedPin
		field = "TS communication status LED",					communicationLedPin
	    field = "Trigger error LED",					triggerErrorPin
		field = "Fatal Error Led",						fatalErrorPin

;			Engine->MIL Settings
	dialog = malfunction,	"Check Engine Settings"
		field = "Pin",         			malfunctionIndicatorPin
		field = "Pin mode",				malfunctionIndicatorPinMode	
		field = "Warning Period",									warningPeriod

;			Engine->hip9011 Settings
	dialog = hipFunction, "HIP9011 Settings (knock decoder)"
		field = "Enabled",								isHip9011Enabled
		field = "Threshold",							knockVThreshold, {isHip9011Enabled == 1}
		field = "!ECU reboot needed to apply these settings"
		field = "IntHold pin (hip9011 input)",      	hip9011IntHoldPin, {isHip9011Enabled == 1}
		field = "IntHold pin (hip9011 input) mode",		hip9011IntHoldPinMode, {isHip9011Enabled == 1}
		field = "ChipSelect pin",						hip9011CsPin, {isHip9011Enabled == 1}
		field = "ChipSelect mode",						hip9011CsPinMode, {isHip9011Enabled == 1}
		field = "hip Output/stm input",					hipOutputChannel, {isHip9011Enabled == 1}
		field = "prescaler & SDO",						hip9011PrescalerAndSDO, {isHip9011Enabled == 1}
		field = "knockDetectionWindowStart",			knockDetectionWindowStart, {isHip9011Enabled == 1}
		field = "knockDetectionWindowEnd",				knockDetectionWindowEnd, {isHip9011Enabled == 1}
		field = "cylinder bore (mm)",					cylinderBore, {isHip9011Enabled == 1}
		field = "Band Freq override",					knockBandCustom, {isHip9011Enabled == 1}
		field = "SPI device",							hip9011SpiDevice, {isHip9011Enabled == 1}
		panel = knockThresholdCurve
		
;			Engine->cj125 Settings
	dialog = cj125Function, "CJ125 Settings (wbo decoder)"
		field = "Enabled",								isCJ125Enabled
		field = "Using 4.9 sensor?",					cj125isLsu49
		field = "!ECU reboot needed to apply these settings"
		field = "ChipSelect pin",						cj125CsPin, {isCJ125Enabled == 1}
		field = "ChipSelect mode",						cj125CsPinMode, {isCJ125Enabled == 1}
		field = "!See also 'Controller-SPI setting'"
		field = "SPI device",							cj125SpiDevice
		field = "Heater pin",							wboHeaterPin, {isCJ125Enabled == 1}
		field = "UA input",								cj125ua, {isCJ125Enabled == 1}
		field = "UR input",								cj125ur, {isCJ125Enabled == 1}
		field = "Is UA input divided?"					cj125isUaDivided, {isCJ125Enabled == 1}
		
	dialog = spiFunction, "SPI settings"
		field = "!ECU reboot needed to apply these settings"
		field = "SPI1 enable",							is_enabled_spi_1
		field = "SPI1 MOSI",							spi1mosiPin, {is_enabled_spi_1 == 1}
		field = "SPI1mosi mode",						spi1MosiMode, {is_enabled_spi_1 == 1}
		field = "SPI1 MISO",							spi1misoPin, {is_enabled_spi_1 == 1}
		field = "SPI1miso mode",						spi1MisoMode, {is_enabled_spi_1 == 1}
		field = "SPI1 SCK",								spi1sckPin, {is_enabled_spi_1 == 1}
		field = "SPI1sck mode",							spi1SckMode, {is_enabled_spi_1 == 1}

		field = "SPI2 enable",							is_enabled_spi_2
		field = "SPI2 MOSI",							spi2mosiPin, {is_enabled_spi_2 == 1}
		field = "SPI2mosi mode",						spi2MosiMode, {is_enabled_spi_2 == 1}
		field = "SPI2 MISO",							spi2misoPin, {is_enabled_spi_2 == 1}
		field = "SPI2miso mode",						spi2MisoMode, {is_enabled_spi_2 == 1}
		field = "SPI2 SCK",								spi2sckPin, {is_enabled_spi_2 == 1}
		field = "SPI2sck mode",							spi2SckMode, {is_enabled_spi_2 == 1}

		field = "SPI3 enable",							is_enabled_spi_3
		field = "SPI3 MOSI",							spi3mosiPin, {is_enabled_spi_3 == 1}
		field = "SPI3mosi mode",						spi3MosiMode, {is_enabled_spi_3 == 1}
		field = "SPI3 MISO",							spi3misoPin, {is_enabled_spi_3 == 1}
		field = "SPI3miso mode",						spi3MisoMode, {is_enabled_spi_3 == 1}
		field = "SPI3 SCK",								spi3sckPin, {is_enabled_spi_3 == 1}
		field = "SPI3sck mode",							spi3SckMode, {is_enabled_spi_3 == 1}
		field = "LIS302DLCsPin",						LIS302DLCsPin

	dialog = fuelClosedLoopDialog, "Fuel short-term closed-loop correction"
		field = "#This is just the cherry on the cake once you have good VE table"
		field = "Enabled",								fuelClosedLoopCorrectionEnabled
		field = "!No correction below these value"
		field = "CLT - low threshod", 					fuelClosedLoopCltThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "RPM - low threshod", 					fuelClosedLoopRpmThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "EGO - low threshod", 					fuelClosedLoopAfrLowThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "!No correction above these value"
		field = "TPS - high threshod", 					fuelClosedLoopTpsThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "EGO - high threshod", 					fuelClosedLoopAfrHighThreshold, {fuelClosedLoopCorrectionEnabled == 1}
		field = "!PID settings"
		field = "P factor",								fuelClosedLoopPid_pFactor, {fuelClosedLoopCorrectionEnabled == 1}
		field = "I factor",								fuelClosedLoopPid_iFactor, {fuelClosedLoopCorrectionEnabled == 1}
		field = "D factor",								fuelClosedLoopPid_dFactor, {fuelClosedLoopCorrectionEnabled == 1}
		field = "min",									fuelClosedLoopPid_minValue, {fuelClosedLoopCorrectionEnabled == 1}
		field = "max",									fuelClosedLoopPid_maxValue, {fuelClosedLoopCorrectionEnabled == 1}


	dialog = auxPidDialog, "Aux PID"
		field = "Enabled",								activateAuxPid1
		field = "FSIO pin #1",							auxPidPins1
		field = "PWM Frequency",						auxPidFrequency1
		field = "Detailed status in console",			isVerboseAuxPid1
		field = "#target based on FSIO map#1"
		field = "control period",						auxPid1_periodMs, {activateAuxPid1 == 1}
		field = "#PID control"
		field = "offset",								auxPid1_offset, {activateAuxPid1 == 1}
		field = "P factor",								auxPid1_pFactor, {activateAuxPid1 == 1}
		field = "I factor",								auxPid1_iFactor, {activateAuxPid1 == 1}
		field = "D factor",								auxPid1_dFactor, {activateAuxPid1 == 1}
		field = "Min",									auxPid1_minValue, {activateAuxPid1 == 1}
		field = "Max",									auxPid1_maxValue, {activateAuxPid1 == 1}
		field = "FSIO pin #2",							auxPidPins2
		field = "FSIO pin #3",							auxPidPins3
		field = "FSIO pin #4",							auxPidPins4

;			Engine->Battery & Alternator
	dialog = batteryDialog, "Battery Settings",	yAxis
		field = "vBatt ADC input", 						vbattAdcChannel
		field = "Battery Input Divider Coefficient",	vbattDividerCoeff
	dialog = alternator, "Alternator Settings",	yAxis
		field = "Enabled",								isAlternatorControlEnabled
		field = "simple on/off mode",					onOffAlternatorLogic, {isAlternatorControlEnabled == 1}
		field = "Target",								targetVBatt, {isAlternatorControlEnabled == 1}
		field = "Pin",									alternatorControlPin, {isAlternatorControlEnabled == 1}
		field = "Pin Mode",								alternatorControlPinMode, {isAlternatorControlEnabled == 1}
		field = "PWM frequency",						alternatorPwmFrequency, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Off Above TPS",						alternatorOffAboveTps, {isAlternatorControlEnabled == 1}
		field = "Detailed status in console",			isVerboseAlternator, {isAlternatorControlEnabled == 1}
		field = "control period",						alternatorControl_periodMs, {isAlternatorControlEnabled == 1}
		field = "#PID control"
		field = "offset",								alternatorControl_offset, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "P factor",								alternatorControl_pFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "I factor",								alternatorControl_iFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "D factor",								alternatorControl_dFactor, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Min",									alternatorControl_minValue, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "Max",									alternatorControl_maxValue, {isAlternatorControlEnabled == 1 && onOffAlternatorLogic == 0}
		field = "#% duty = Pterm + Iterm + Dterm + offset%"


	dialog = warmupFuelDialog, "Warmup fuel closed-loop",	yAxis
		field = "use automatic Pid Afr control",			useWarmupPidAfr
		field = "warmup temperature Threshold",				warmupAfrThreshold
		field = "wa offset",								warmupAfrPid_offset
		field = "wa P factor",								warmupAfrPid_pFactor
		field = "wa I factor",								warmupAfrPid_iFactor
		field = "wa D factor",								warmupAfrPid_dFactor
		field = "#correction = Pterm + Iterm + Dterm + offset"
		
		
	dialog = energySystems, "Battery and Alternator Settings",	yAxis
		panel = batteryDialog
		panel = alternator

	dialog = speedSensorLeft
		field = "Input pin",					vehicleSpeedSensorInputPin
		field = "revolution to speed mult",				vehicleSpeedCoef

	dialog = speedSensor, "Speed sensor", xAxis
		panel = speedSensorLeft
		gauge = VSSGauge

;			Engine->Other inputs	
	dialog = analogInputSettings, "Analog Input Settings"
		field = "!ECU reboot needed to apply these settings"
		field = "Use fixed baro corr from MAP", 		useFixedBaroCorrFromMap
		field = "Analog divider",						analogInputDividerCoefficient
		field = "Use BiQuad averaging",					useBiQuadAnalogFiltering		
		field = "Smoothing factor",						slowAdcAlpha, {useBiQuadAnalogFiltering == 0}
		field = "Bi_Q a0",								biQuad_a0, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q a1",								biQuad_a1, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q a2",								biQuad_a2, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q b1",								biQuad_b1, {useBiQuadAnalogFiltering == 1}
		field = "Bi_Q b2",								biQuad_b2, {useBiQuadAnalogFiltering == 1}

	dialog = tachSettings, "Tachometer output"
		field = "!See also dizzySparkOutputPin"
		field = "Pin",									tachOutputPin
		field = "Pin mode",								tachOutputPinMode
		field = "Rise at trigger index",				tachPulseTriggerIndex
		field = "Pulse duration is duty cycle",			tachPulseDurationAsDutyCycle
		field = "Pulse duration",						tachPulseDuractionMs


;			Board->Connection
	dialog = tsPort, "TunerStudio Port"
		field = "tunerStudioSerialSpeed",				tunerStudioSerialSpeed
		field = "Use PC10/PC11 serial?",				useSerialPort
		field = "uartConsoleSerialSpeed",				uartConsoleSerialSpeed
		
	dialog = canBus, "CAN Bus"
		field = "Can Read Enabled",						canReadEnabled
		field = "Can Write Enabled",					canWriteEnabled
		field = "Can Nbc Type",							canNbcType
		field = "Can Sleep Period",						canSleepPeriodMs
		field = "RX pin",								canRxPin
		field = "TX pin",								canTxPin
	
	dialog = sdCard, "SD Card Logger"
		field = "SdCard", 								isSdCardEnabled
		field = "showSdCardWarning",					showSdCardWarning
		field = "CS Pin",								sdCardCsPin
		field = "SPI",									sdCardSpiDevice
		field = "log format",							logFormat
		field = "Mass Storage",							storageMode
	
	dialog = gpsReceiver, "GPS Receiver" 
		field = "gps RX", 								gps_rx_pin
		field = "gps TX", 								gps_tx_pin
		
	dialog = lcdScreen, "LCD screen"
		field = "display Mode",							displayMode
		field = "height", 								HD44780height
		field = "width", 								HD44780width
		field = "RS pin", 								HD44780_rs
		field = "E pin", 								HD44780_e
		field = "D4 pin", 								HD44780_db4
		field = "D5 pin", 								HD44780_db5
		field = "D6 pin", 								HD44780_db6
		field = "D7 pin", 								HD44780_db7
		
	dialog = tle8888, "TLE8888", yAxis
		field = "TLE8888 Chip Select", 					tle8888_cs
		field = "TLE8888 SPI", 							tle8888spiDevice

	dialog = connection, "", 	yAxis
		field = "STM32 vRef voltage",					adcVcc
		panel = tsPort
		panel = canBus
		panel = sdCard
		panel = gpsReceiver                       @@if_ts_show_gps
		panel = tle8888

	dialog = joystickPanel, "Joystick"
		field = "joustick center button",				joystickCenterPin
		field = "joustick button A",					joystickAPin
		field = "joustick button B",					joystickBPin
		field = "joustick button C",					joystickCPin
		field = "joustick button D",					joystickDPin
				
	dialog = monitoringSettings, "rusEfi Console Settings"			
		field = "Sensor Sniffer",         	    		sensorChartMode
		field = "  Threshold",							sensorSnifferRpmThreshold
		field = "  Each X cycle",						sensorChartFrequency
		field = "Engine Sniffer", 						isEngineChartEnabled			
		field = "  Threshold", 							engineSnifferRpmThreshold
		
	dialog = generalSettings, "General"
		field = "!https://rusefi.com/s/fuel"
		field = "Fuel strategy",						fuelAlgorithm
		
	dialog = debugging, "Debug"
		field = "!https://rusefi.com/s/debugmode"
		field = "Debug mode",							debugMode

	
	dialog = limits, "Limits"
		field = "RPM hard limit",         	    		rpmHardLimit
		field = "Boost cut pressure",					boostCutPressure
	
;			Engine->Base Engine Settings
	dialog = engineChars, "Base Engine Settings"
		topicHelp = "baseHelp"
		panel = baseEngineConfig
		panel = generalSettings
		panel = limits
		panel = debugging

	dialog = crankingFuel, "Fuel"
		field = "Injection mode",						crankingInjectionMode
		field = "!Value '1' is currently recommended"
		field = "Base fuel pulse width", 				cranking_baseFuel
		
	dialog = crankingIAC, "IAC"
		field = "Cranking IAC position",					crankingIACposition
		field = "After cranking IAC taper duration",	afterCrankingIACtaperDuration
		field = "Override IAC multiplier for cranking",	overrideCrankingIacSetting
		
	dialog = crankingIgnition, "Ignition"
		field = "Advance", 								crankingTimingAngle, {useSeparateAdvanceForCranking == 0}
		field = "Use separate Advance Table for cranking",	useSeparateAdvanceForCranking
		field = "Use Advance Corrections for cranking",	useAdvanceCorrectionsForCranking
        field = "Use fixed cranking dwell",         			useConstantDwellDuringCranking
        field = "Fixed Cranking Dwell",           			ignitionDwellForCrankingMs, {useConstantDwellDuringCranking == 1}
		field = "Cranking Dwell Angle", 						crankingChargeAngle, {useConstantDwellDuringCranking == 0}
	
	dialog = postCrankingEnrichment, "Post-cranking short-time fuel enrichment (NOT IMPLEMENTED #331)"
		field = "Post-Cranking factor", 				postCrankingFactor
		field = "Duration", 				postCrankingDurationSec
		
	dialog = primingFuelPulsePanel, "Priming fuel pulse"
		field = "Duration at -40C degrees",	startOfCrankingPrimingPulse
		field = "Falloff temperature", primeInjFalloffTemperature
		
		
;			Cranking->Cranking Settings
	dialog = crankingDialog, "Cranking Settings"
		field = "Cranking RPM limit",                	cranking_rpm
		field = "Enable cylinder cleanup",				isCylinderCleanupEnabled
		field = ""
		field = "Enable faster engine spin-up",			isFasterEngineSpinUpEnabled
		panel = primingFuelPulsePanel
		panel = crankingFuel
		panel = crankingIgnition
		panel = crankingIAC
		panel = postCrankingEnrichment

	dialog = EngineLoadAccelPanel, "Engine Load (alpha version)"
		field = "Length",						engineLoadAccelLength
		field = "Accel threshold", 				engineLoadAccelEnrichmentThreshold
		field = "Accel multiplier",	 			engineLoadAccelEnrichmentMultiplier
		field = "Decel threshold", 				engineLoadDecelEnleanmentThreshold
		field = "Decel multiplier",	 			engineLoadDecelEnleanmentMultiplier

	dialog = TpsAccelPanel, "TPS"
		field = "Set 'Debug Mode' to see detailed 'TPS acceleration enrichment' diagnostics"
   		field = "Length",						tpsAccelLength
		field = "Accel Threshold", 				tpsAccelEnrichmentThreshold
		field = "Decel Threshold", 				tpsDecelEnleanmentThreshold
;		field = "Decel Multiplier",	 			tpsDecelEnleanmentMultiplier
		field = "#Accelerator Pump model:"
		field = "Fraction Period",				tpsAccelFractionPeriod
		field = "Fraction Divisor",				tpsAccelFractionDivisor
		
	dialog = WallWettingAccelPanel, "Wall Wetting (alpha version)"
		field = "evaporation time constant",          wwaeTau
		field = "added to wall coef",                   wwaeBeta
	
		
;			Tuning->AccelEnrichment
	dialog = AccelEnrich,	"Accel/Decel Enrichment"
		panel = TpsAccelPanel
		panel = WallWettingAccelPanel
		panel = EngineLoadAccelPanel
		field = "No accel after RPM hard limit",		noAccelAfterHardLimitPeriodSecs
		
		
;			Flex Logic
	dialog = fsioIO, "Outputs"
		field = "output #1", 							fsioOutputPins1
		field = "output #2", 							fsioOutputPins2
		field = "output #3", 							fsioOutputPins3
		field = "output #4", 							fsioOutputPins4
		field = "output #5", 							fsioOutputPins5
		field = "output #6", 							fsioOutputPins6
		field = "output #7", 							fsioOutputPins7
		field = "output #8", 							fsioOutputPins8
		field = "output #9", 							fsioOutputPins9
		field = "output #10", 							fsioOutputPins10
		field = "output #11", 							fsioOutputPins11
		field = "output #12", 							fsioOutputPins12
		field = "output #13", 							fsioOutputPins13
		field = "output #14", 							fsioOutputPins14
		field = "output #15", 							fsioOutputPins15
		field = "output #16", 							fsioOutputPins16
		field = "aux valve #1", 						auxValves1
		field = "aux valve #2", 						auxValves2
		field = ""
		field = ""
		
	dialog = fsioFrequency, "Frequency"
		field = "freq #1", 								fsioFrequency1
		field = "freq #2", 								fsioFrequency2
		field = "freq #3", 								fsioFrequency3
		field = "freq #4", 								fsioFrequency4
		field = "freq #5", 								fsioFrequency5
		field = "freq #6", 								fsioFrequency6
		field = "freq #7", 								fsioFrequency7
		field = "freq #8", 								fsioFrequency8
		field = "freq #9", 								fsioFrequency9
		field = "freq #10", 							fsioFrequency10
		field = "freq #11", 							fsioFrequency11
		field = "freq #12", 							fsioFrequency12
		field = "freq #13", 							fsioFrequency13
		field = "freq #14", 							fsioFrequency14
		field = "freq #15", 							fsioFrequency15
		field = "freq #16", 							fsioFrequency16
		field = ""
		field = ""
	
	dialog = fsioSetting, "Setting"
		field = "Set number is not associated with the output number."
		field = "Set number, only the cell number with some numbers."
		field = "set #1",								fsio_setting1
		field = "set #2",								fsio_setting2
		field = "set #3",								fsio_setting3
		field = "set #4",								fsio_setting4
		field = "set #5",								fsio_setting5
		field = "set #6",								fsio_setting6
		field = "set #7",								fsio_setting7
		field = "set #8",								fsio_setting8
		field = "set #9",								fsio_setting9
		field = "set #10",								fsio_setting10
		field = "set #11",								fsio_setting11
		field = "set #12",								fsio_setting12
		field = "set #13",								fsio_setting13
		field = "set #14",								fsio_setting14
		field = "set #15",								fsio_setting15
		field = "set #16",								fsio_setting16
		
	dialog = fsioOutputsDialog, "FSIO outputs", border
		panel = fsioIO,			West
		panel = fsioFrequency,	Center
		panel = fsioSetting,	East
		
	dialog = fsioFormulas, "FSIO Formulas"
		field = "!FSIO uses Reverse Polish Notation. Please read http://rusefi.com/s/fsio"
		field = "#1",									fsioFormulas1
		field = "#2",									fsioFormulas2
		field = "#3",									fsioFormulas3
		field = "use FSIO #4 for serious eninge warning",useFSIO4ForSeriousEngineWarning
		field = "#4",									fsioFormulas4
		field = "use FSIO #5 for critical engine stop", useFSIO5ForCriticalIssueEngineStop
		field = "#5",									fsioFormulas5
		field = "#6",									fsioFormulas6
		field = "#7",									fsioFormulas7
		field = "use FSIO #8 for servo #1",	useFSIO8ForServo1
		field = "#8",									fsioFormulas8
		field = "use FSIO #9 for servo #2",	useFSIO8ForServo1
		field = "#9",									fsioFormulas9
		field = "use FSIO #10 for servo #3",	useFSIO8ForServo1
		field = "#10",									fsioFormulas10
		field = "use FSIO #11 for servo #4",	useFSIO8ForServo1
		field = "#11",									fsioFormulas11
		field = "use FSIO #12 for servo #5",	useFSIO8ForServo1
		field = "#12",									fsioFormulas12
		field = "#13",									fsioFormulas13
		field = "#14",									fsioFormulas14
		field = "use FSIO #15 for target idle RPM adjustment",	useFSIO15ForIdleRpmAdjustment
		field = "#15",									fsioFormulas15
		field = "use FSIO #16 for timing adjustment",	useFSIO16ForTimingAdjustment
		field = "#16",									fsioFormulas16
		
	dialog = fsioInputsDialog, "FSIO inputs"
		field = "ADC #1",								fsioAdc1
		field = "ADC #2",								fsioAdc2
		field = "ADC #3",								fsioAdc3
		field = "ADC #4",								fsioAdc4
				
	help = veTableDialogHelp, "Volumetric Efficiency"
        text = "Volumetric Efficiency is used to calculate fuel in Speed Density mode"
        webHelp = "https://rusefi.com/s/fuel"
        
    help = fuelHelp, "Fuel Control"    
        text = "More about fuel control on the web"
        webHelp = "https://rusefi.com/s/fuel"
				
    help = etbHelp, "ETB Control"
        text = "More about electronic throttle body on the web"
        webHelp = "https://rusefi.com/s/etb"

    help = tpsTpsHelp, "Acceleration Enrichment"
        text = "More about Tps To Tps acceleration on the web"
        webHelp = "https://rusefi.com/s/tpstps"

    help = baseHelp, "Base Settings Control"    
        text = "More about rusefi on the web"
        webHelp = "https://rusefi.com/"

	dialog = veTableDialog
		topicHelp = "veTableDialogHelp"
		panel = veTableTbl, South
				
	dialog = veTableDialog3D, "VE Table"
		topicHelp = "veTableDialogHelp"
		panel = veTableMap, South

	dialog = etbPidDialog, "PID settings"
		field = "pFactor",								etb_pFactor, {throttlePedalPositionAdcChannel != 16}
		field = "iFactor",								etb_iFactor, {throttlePedalPositionAdcChannel != 16}
		field = "dFactor",								etb_dFactor, {throttlePedalPositionAdcChannel != 16}
		field = "offset",								etb_offset, {throttlePedalPositionAdcChannel != 16}
		field = "control period",						etb_periodMs, {throttlePedalPositionAdcChannel != 16}
		field = "pid min",								etb_minValue, {throttlePedalPositionAdcChannel != 16}
		field = "pid max",								etb_maxValue, {throttlePedalPositionAdcChannel != 16}
		field = "iTermMin",								etb_iTermMin, {throttlePedalPositionAdcChannel != 16}
		field = "iTermMax",								etb_iTermMax, {throttlePedalPositionAdcChannel != 16}


	dialog = etbDialogLeft
		field = "https://rusefi.com/s/etb"
		field = "Detailed status in console",			isVerboseETB
		field = "Pause ETB control",					pauseEtbControl
		field = "Throttle Pedal Up",					throttlePedalUpVoltage
		field = "Throttle Pedal Wide Open",				throttlePedalWOTVoltage
		field = "PWM Frequency",						etbFreq, {throttlePedalPositionAdcChannel != 16}
		field = "No1 Direction #1",						etb1_directionPin1, {throttlePedalPositionAdcChannel != 16}
		field = "No1 Direction #2",						etb1_directionPin2, {throttlePedalPositionAdcChannel != 16}
		field = "Two-wire mode",						etb1_use_two_wires, {throttlePedalPositionAdcChannel != 16}
		field = "No1 Control #1",						etb1_controlPin1, {throttlePedalPositionAdcChannel != 16 && etb1_use_two_wires == 0}
		field = "No2 Direction #1",						etb2_directionPin1, {throttlePedalPositionAdcChannel != 16}
		field = "No2 Direction #2",						etb2_directionPin2, {throttlePedalPositionAdcChannel != 16}
		field = "Two-wire mode",						etb2_use_two_wires, {throttlePedalPositionAdcChannel != 16}
		field = "No2 Control #1",						etb2_controlPin1, {throttlePedalPositionAdcChannel != 16 && etb2_use_two_wires == 0}
		panel = etbPidDialog

	dialog = etbDialogRight
		field = "!https://rusefi.com/s/debugmode"
		field = "Debug mode",							debugMode
		field = "use ETB for idle",						useETBforIdleControl
		field = "ETB idle maximum angle",				etbIdleRange
		field = "Press buttons to calibrate sensors"
		field = "You would have to remove air filter to move throttle manually"
	    commandButton = "TPS#1 closed position", cmd_calibrate_tps_1_closed
	    commandButton = "TPS#1 wide open position", cmd_calibrate_tps_1_wot
	    field = "Not many vehicles have two throttle bodies but some do"
	    commandButton = "TPS#2 closed position", cmd_calibrate_tps_2_closed
	    commandButton = "TPS#2 wide open position", cmd_calibrate_tps_2_wot
	    commandButton = "Pedal Up", cmd_calibrate_pedal_up
	    commandButton = "Pedal Down", cmd_calibrate_pedal_down

	dialog = etbDialog, "Electronic Throttle Body (beta)", border
		topicHelp = "etbHelp"
		panel = etbDialogLeft, West
		panel = etbDialogRight, East


	dialog = testSpark, "Spark"
		commandButton = "Spark #1", cmd_test_spk1
		commandButton = "Spark #2", cmd_test_spk2
		commandButton = "Spark #3", cmd_test_spk3
		commandButton = "Spark #4", cmd_test_spk4
		commandButton = "Spark #5", cmd_test_spk5
		commandButton = "Spark #6", cmd_test_spk6
		commandButton = "Spark #7", cmd_test_spk7
		commandButton = "Spark #8", cmd_test_spk8
		
	dialog = testInjectors, "Fuel"
		commandButton = "Injector #1", cmd_test_inj1
		commandButton = "Injector #2", cmd_test_inj2
		commandButton = "Injector #3", cmd_test_inj3
		commandButton = "Injector #4", cmd_test_inj4
		commandButton = "Injector #5", cmd_test_inj5
		commandButton = "Injector #6", cmd_test_inj6
		commandButton = "Injector #7", cmd_test_inj7
		commandButton = "Injector #8", cmd_test_inj8
		
	dialog = testMisc, "Misc"
		commandButton = "Come To Pit", cmd_call_from_pit
		commandButton = "Fuel Pump", cmd_test_fuel_pump
		commandButton = "Radiator Fan", cmd_test_radiator_fan
		commandButton = "Check Engine", cmd_test_check_engine_light
		commandButton = "Idle Air Valve", cmd_test_idle_valve          
		commandButton = "Stop Engine", cmd_stop_engine          
		commandButton = "Reset ECU", cmd_reset_controller

	; bench test	
	dialog = ioTest, "Bench Test & Commands", border
		panel = testSpark,		West
		panel = testInjectors,	Center
		panel = testMisc,		East
	
	dialog = engineTypeDialog, "Popular vehicles"
		field = "!These buttons send a command to rusEfi controller to apply preset values"
		field = "!Once you send the command, please reconnect to rusEfi controller in order to read fresh values"			
		commandButton = "Miata NA6 Stage 0", cmd_set_engine_type_Miata_NA6_VAF
		commandButton = "Miata NA6 Stage 1", cmd_set_engine_type_Miata_NA6_MAP
		commandButton = "Miata NB2 MAP", cmd_set_engine_type_Miata_NA2
		commandButton = "ETB test bench", cmd_set_engine_type_etb_test
		commandButton = "TLE8888B test bench", cmd_set_engine_type_8888_test
		commandButton = "Reset firmware settings", cmd_set_engine_type_default


;			Board->ECU stimulator
	dialog = ecuStimulator, "ECU stimulator"
		field = "Trigger Simulator",   					triggerSimulatorFrequency
		field = "self-stimulation",						directSelfStimulation
		field = ""
		field = "digipot spi", 							digitalPotentiometerSpiDevice
		field = "digipot CS #0", 						digitalPotentiometerChipSelect1
		field = "digipot CS #1", 						digitalPotentiometerChipSelect2
		field = "digipot CS #2", 						digitalPotentiometerChipSelect3
		field = "digipot CS #3", 						digitalPotentiometerChipSelect4
		field = ""
		field = "trigger stimulator pin #1", 			triggerSimulatorPins1
		field = "trigger stimulator pin mode #1", 		triggerSimulatorPinModes1
		field = "trigger stimulator pin #2", 			triggerSimulatorPins2
		field = "trigger stimulator pin mode #2", 		triggerSimulatorPinModes2
		field = "trigger stimulator pin #3", 			triggerSimulatorPins3
		field = "trigger stimulator pin mode #3", 		triggerSimulatorPinModes3
		field = ""
	    field = "Logic input channel 1", 				logicAnalyzerPins1
	    field = "Logic input channel 2", 				logicAnalyzerPins2
	    field = "Logic input channel 3", 				logicAnalyzerPins3
	    field = "Logic input channel 4", 				logicAnalyzerPins4
		field = ""
	    field = "Engine chart size", 					engineChartSize

				;			Racing Features->Launch Control
	dialog = smLaunchControl, "Launch Control Settings NOT WORKING"
		field = "RPM Step1 Limit",         	    		step1rpm
		field = "Launch RPM Window"                     step1RpmWindow
		field = "Step1 Ignition Advance",				step1timing
		field = "Use Spark Cut",						step1SparkCutEnable
		field = "Use Fuel Cut",							step1fuelCutEnable
		field = "clutchDownPin",						clutchDownPin
		field = "clutchUpPin",							clutchUpPin
		field = "brakePedalPin",						brakePedalPin
	    
	dialog = coastingFuelCutControl, "Coasting Fuel Cutoff Settings"
		field = "Enable Coasting Fuel Cutoff",			coastingFuelCutEnabled
		field = "Cutoff Activation RPM High Limit",		coastingFuelCutRpmHigh, {coastingFuelCutEnabled == 1}
		field = "Cutoff Deactivation RPM Low Limit",	coastingFuelCutRpmLow, {coastingFuelCutEnabled == 1}
		field = "TPS Deactivation Threshold",			coastingFuelCutTps, {coastingFuelCutEnabled == 1}
		field = "CLT Activation Threshold",				coastingFuelCutClt, {coastingFuelCutEnabled == 1}
		field = "MAP Deactivation Threshold",      coastingFuelCutMap, {coastingFuelCutEnabled == 1}

	dialog = parkingLot, "Experimental/Broken"
		field = "#System hacks"
		field = "Global fuel correction", 				globalFuelCorrection
		field = "Ignition Math Logic @",				ignMathCalculateAtIndex
		field = "MAP Averaging Logic @",				mapAveragingSchedulingAtIndex

		field = "Target temperature", 			postCrankingTargetClt
		
		panel = warmupFuelDialog

[Tools]
 ;addTool = toolName, PanelName
 addTool = veTableGenerator, "VE Table Generator", veTableTbl
 addTool = afrTableGenerator, "AFR Table Generator", afrTableTbl