* remove simple cases
* more simple
* serial
* s
* more
* try memory
* easy
* mmc acc
* that's how much memory
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* enable
* guard correctly
* h7 bit timing
* allow longer frames
* allow data smaller than maximum
* mcu temperature
* typo
* tx message
* testing
* check for CAN or FDCAN
* don't need that any more
* h7 bitrate config
* undo testing
* h7-ify msg tx
* comment
* break out SID/EID macros
* guard differently
* update ChibiOS
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* configure for no cache
* this doesn't need a setting
* now we don't need invalidate
* reorder and comment
* mmc
* sw knock
* use spiPolledExchange for small transfers
* mock spi
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* ChibiOS: add support for STM32F765
This chip is used on Subaru EG33 p'n'p RusEFI board from Dron_Gus
* drivers: gpio: mc33810: commulative update
- use BIT macro
- fix wake-up method
- fix order of arguments in _add function
* port: stm32f4/7: detectCanDevice check for enabled interfaces only
* ADC: fix internal array size
internalAdcIndexByHardwareIndex should be EFI_ADC_LAST_CHANNEL size
couse adc_channel_e is used as index
* status LEDs: support status LEDs that driven by low level
* Proper way to add lis302 driver
* Proper way to add license directory to includes
* Makefile: simplify
All ChibiOS stuff is accumulated in ALLCSRC, ALLINC and so on.
* board.mk: append sources and includes to ALLSRC, ALLCPPSRC, ALLINC
* Cypress: fix CANv2 includence into build
* gpios: isBrainPinValid helper
* LCD HD44780: do not touch pins if DM_NONE or invalid gpio
* Fix isEnabled checks for GPS and Joystick
* LCD HD44780: writePad use this method wider
* We still need consoleEventListener for boards with EFI_CONSOLE_SERIAL_DEVICE
* MC33810: add MC_ prefix for command defines
As CMD_PWM define is now used by console command
* switch to CriticalSectionLocker
* that's just about all
* clean up last usage
* include hpp for sim
* need the cpp wrappers in the makefile too
* include dir
* include
* TLE8888: add support MR switching from SW
Main Relay has limitation - it is always active while KEY=1. When
KEY=0 MR can be switched on from SW.
* TLE8888: support reading of KEY and WAKE inputs
* Rusefi enums: add new TLE8888 pins
* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
* second can bus, first steps
* added most important messages; no more errors
* cleaned up can messages
* second can bus, first steps
* added most important messages; no more errors
* cleaned up can messages
* post rebase/merge fixes
* more rebase/merge fixes
* even more rebase/merge fixes
* more fixes, removed auto-gen files
* removed more auto-gen files...
This fixes following build issue under linux:
make: *** No rule to make target 'build/obj/.cpp cj125.cpp', needed by 'build/obj/ build/obj/cj125.o'. Stop.
make: *** Waiting for unfinished jobs....
Introduces in 8d35c35035
* aux serial updates from last PR
* trying to guess
* wow that's old! also not working maybe?
* hiding diag code which was messing with GP2/GP3 i.e. TLE8888_PIN_22 TLE8888_PIN_23
* date
* Mc33 undervolt (#1421)
* mc33 flash check
* DI sanity checks for setting HV config
* mc33 under voltage check
* mc33 under voltage check
Co-authored-by: Christopher W. Anderson <gitstuff@pswitch.com>
* fixed {}
Co-authored-by: rusefi <rusefillc@gmail.com>
Co-authored-by: NOx-z <50815960+NOx-z@users.noreply.github.com>
Co-authored-by: Christopher W. Anderson <gitstuff@pswitch.com>
Co-authored-by: kon <dev@triggerdevel>
* tle8888: fix tle8888_chip_init flow
* tle8888: set correct pin modes for mcu gpios in tle8888_chip_init
Direct drive, reset, inj_en and ign_en gpio should be outputs
shadowm60
Matthew Kennedy
Andrey G
rusefillc
rusefi
kon