162 lines
5.5 KiB
Markdown
162 lines
5.5 KiB
Markdown
<a href="https://www.ebay.com/itm/334094173341"><img src="Images/ebay_gen_button.gif"></a>
|
|
|
|
This development board is PnP for Mercedes with the 128 Pin ECU (could be used on M104, M111, M112 and M113 engine; late 90s-early 2000s. confirm your ECU _harness_)
|
|
|
|
[Download release firmware](https://github.com/rusefi/rusefi/releases/latest/download/rusefi_bundle_hellen128.zip)
|
|
[Snapshot firmware bundle](https://rusefi.com/build_server/rusefi_bundle_hellen128.zip)
|
|
|
|
[Pinout](https://rusefi.com/docs/pinouts/hellen/hellen128/) & [Google Sheet](https://docs.google.com/spreadsheets/d/1I-lZKRajTiEGFUXdZpXEtKF2pymlOo-lPahy3cLMnl4) & [Another Google Sheet](https://docs.google.com/spreadsheets/d/1JgGFJ8AggBFiKT_CQ1D6uYhaIsqeiH9RerxuVy1kp4Y/)
|
|
|
|
[Issue Tracker](https://github.com/rusefi/hellen128merc-issues/issues)
|
|
|
|
[Schematics rev a]](Hardware/Hellen/hellen128mercedes-a-schematic.pdf)[[iBom rev a](https://rusefi.com/docs/ibom/hellen128mercedes-a-ibom.html)
|
|
|
|
[Schematics rev b]](Hardware/Hellen/hellen128mercedes-b-schematic.pdf)[[iBom rev b](https://rusefi.com/docs/ibom/hellen128mercedes-b-ibom.html)
|
|
|
|
## Hardware features
|
|
|
|
* ME 2.0 pinout
|
|
* supports both smart and dumb coils
|
|
* ?
|
|
* one or two channels of [rusEFI-Wideband-Controller](https://github.com/rusefi/rusefi/wiki/rusEFI-Wideband-Controller)
|
|
|
|
4 cylinder configuration
|
|
|
|
![x](Hardware/Hellen/hellen128mercedes-rev-b-reference-4-cylinder.jpg)
|
|
|
|
With R80 on the back side
|
|
|
|
[test points](Hardware/Hellen/hellen128mercedes-rev-b-reference-4-cylinder-test-points.png)
|
|
|
|
[Rev B naked board](Hardware/Hellen/hellen128mercedes-rev-b.jpg)
|
|
|
|
[Rev A naked board](Hardware/Hellen/hellen128mercedes-rev-a.jpg)
|
|
|
|
|
|
|
|
## Extension Pads (rev. a)
|
|
|
|
| Pin | Type | Comments |
|
|
|---|---|---|
|
|
||**Outputs**||
|
|
| P33 | Bridge driver B | 3 A peak |
|
|
| P34 | Low side | 0.5 A |
|
|
| P35 | Low side | 0.5 A |
|
|
| | **Inputs** | |
|
|
| P30 | Analog pull up | |
|
|
| P31 | Analog pull down | |
|
|
| P32 | Analog pull down | |
|
|
| | **MCU** | |
|
|
| J1 | SPI, UART/GPIO | See schematic for details |
|
|
| | **WBO1** | |
|
|
| J9 | XH-8 WBO1 connector| |
|
|
| P19 | GND | |
|
|
| P21 | H- | |
|
|
| P22 | R Trim | |
|
|
| P23 | Ip | |
|
|
| P24 | Vs/Ip | |
|
|
| P25 | Vs | |
|
|
| J7 | SWD| |
|
|
| | **WBO2** | |
|
|
| J18 | XH-8 WBO2 connector| |
|
|
| P18 | GND | |
|
|
| P20 | H- | |
|
|
| P26 | R Trim | |
|
|
| P27 | Ip | |
|
|
| P28 | Vs/Ip | |
|
|
| P29 | Vs | |
|
|
| J19 | SWD | |
|
|
|
|
## Extension Pads (rev. b)
|
|
|
|
| Pin | Type | Comments |
|
|
|---|---|---|
|
|
||**Outputs**||
|
|
| P19 | Low side | 0.5 A |
|
|
| P33 | Bridge driver B | 3 A peak |
|
|
| P34 | Low side | 0.5 A |
|
|
| P35 | Low side | 0.5 A |
|
|
| | **Inputs** | |
|
|
| P30 | Analog pull up | |
|
|
| P31 | Analog pull down | |
|
|
| P32 | Analog pull down | |
|
|
| P36 | Analog pull down | |
|
|
| P40 | Analog pull up | |
|
|
| P41 | Analog pull up | |
|
|
| | **MCU** | |
|
|
| J1 | SPI, UART/GPIO | See schematic for details |
|
|
| | **WBO1** | |
|
|
| J9 | XH-8 WBO1 connector| |
|
|
| | **WBO2** | |
|
|
| J18 | XH-8 WBO2 connector| |
|
|
|
|
## Ignition jumpers (rev. a, rev. b)
|
|
|
|
| Vehicle | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | F13 | F14 | F15 | F16 | F17 |
|
|
| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |
|
|
| Connctor pin **(NOT jumper designator!!!)** | F4 | F5 | F6 | F7 | F9 | F10 | F11 | F12 | F13 | F14 | F16 | F17 | F18 | F19 | F20 | F21 |
|
|
| IGNx signal | IGN5 | IGN5 | IGN3 | IGN3 | IGN7 | IGN7 | IGN8 | IGN8 | IGN4 | IGN4 | IGN2 | IGN6 | IGN6 | IGN2 | IGN1 | IGN1 |
|
|
| 4 cyl 2 coil | 🟡 | 🟡 | 🟡 | 🟡 | 🟡 | 🟡 | 🟡 | 🟡 | ✔️ | 🟡 | 🟡 | 🟡 | 🟡 | 🟡 | ✔️ | 🟡 |
|
|
| Other model | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? | ? |
|
|
|
|
🟡 - it doesn't matter, the specified pin is not connected
|
|
|
|
| Coil type | R43 | R59 | R67 | R60 | R79 | R66 | R74 | R62 | R76 | R63 | R77 | R64 | R78 | R65 | R73 | R61 |
|
|
| --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- | --- |
|
|
| Dumb | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ |
|
|
| Smart | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ | ✔️ | ❌ |
|
|
|
|
|
|
# 4 cylinder application
|
|
* uses inj 5-6-7-8 for INJ
|
|
* two IGBT: Q1 & Q3
|
|
* one MOSFET soldered instead of IBGT for clutch solenoid
|
|
* INJ3 with fly-back for boost control solenoid
|
|
|
|
# M104
|
|
* three IGBT: Q1, Q3 & Q5
|
|
|
|
|
|
|
|
[Vault-Of-Mercedes-OEM](Vault-Of-Mercedes-OEM)
|
|
|
|
[Mercedes-C230-and-SLK230](Mercedes-C230-and-SLK230)
|
|
|
|
|
|
# FAQ
|
|
|
|
## Would this work on my all original Mercedes?
|
|
|
|
Hellen 128 was originally designed for M111 swaps into W201. Depending on the year some W202, R170 and other models could be driven with different amount of supporting mods:
|
|
|
|
* Somewhere around 99 Mercedes has transitioned from just plain wires on C40 and D3 to CAN-bus starter security. For those later models one would have simplify starter wiring and add a start button
|
|
|
|
* And obviously your engine harness should use <a href="Images/mercedes-128.png">this ME 2.0 style of plug</a> not <a href="Images/mercedes-134.png">this 134 pin style of plug</a>.
|
|
|
|
|
|
|
|
|
|
|
|
# Changelog
|
|
|
|
## rev C
|
|
* wastegate diode
|
|
|
|
## rev B Aug 27, 2021
|
|
|
|
* better provisions for high-current control of supercharger [clutch solenoid on M111 Q6 R80](https://github.com/rusefi/hellen128merc-issues/issues/10)
|
|
* ignition fuse changed from 36915000000 5A to 2010-T10A0V2T11192AM5G 10A. 0697H9100-02 could be use for refitting of rev A
|
|
|
|
|
|
## rev A June 10, 2021
|
|
|
|
* good to drive, great success!
|
|
|
|
|
|
## Spare Parts
|
|
ISL9V3040S3S is the large IGBT driver (same thing as ISL9V3040S3ST)
|
|
|
|
Smaller NGD8201AN or ISL9V3040D3ST could probably be used as well.
|
|
|
|
|