This way you can use the console/TunerStudio with the ST-Link
In the process, combine TS_PRIMARY_UART and TS_PRIMARY_SERIAL into TS_PRIMARY_PORT, to make UART vs
SERIAL selection more robus. Ditto for TS_SECONDARY_*. Also change use of TS_NO_PRIMARY to be #if
not #ifdef, so that it can be properly set as a compile flag and not be overwritten by various
header files.
* fuel pump
* s
* call correct callback
* more dead
* test adjustment
* don't overflow
* don't need separate function
* java
* give it a name
* generated
* generated
* add to generate script
* import *
* this is so cheap we don't need a flag
* static functions with (void)
* more
* Revert "more"
This reverts commit 246e53441f935451437df186ac92d7df26b62fb6.
* s
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* Makefile: define BOOTLOADER=1 for linker in case of OpenBLT too
This will reserve first 32K of flash for bootloader.
* OpenBLT: include into build
* board: subaru eg33: add OpenBLT board code
* board: subaru eg33: use OpenBLT
* Board: Subaru EG33: OpenBLT: reuse HAL and CMSIS from OpenBLT submodule
* Board: Subaru EG33: OpenBLT: reuse linker file from OpenBLT too
* OpenBLT for MRE
* OpenBLT: MRE: adjust LD memory map for smallest variat of MCU on MRE
* OpenBLT: enable for MRE
* OpenBLT: disable CRC check of user application
This allows us to use DFU tool to flash main application too.
* hex2dfu: fresh binary for linux
* OpenBLT: extract common part of OpenBLT makefiles to openblt.mk
* OpenBLT: enable CRC check of user application for MRE and EG33
CRC (actually just a summ) of few first vectors is stored at 0x1c
offset. This is reserved vector for Cortex-M3, M4 and M7
* common_make: append OpenBLT CRC to dfu files
This should allow to use DFU to do main application update when
when OpenBLT is used as bootloader. hex2dfu will store same
styled CRC as OpenBLT expects to see in user app.
* OpenBLT reorganization
Move common stuff to hw_layer/ports/
* OpenBLT: proteus
* Proteus: enable OpenBLT for F4 and F7
Compilation tested only
* more unification
* hip stub
* comment
* guard
* channel idx
* include
* hip
* move in to engine
* hip9011
* dead stuff
* dead
* fsio
* lcd
* more dead
* Typo fix
* flash_main: always allow to write settings to ext NOR while running
* mc33810: do not enable outputs right after undervoltage
Wait for next active signal
* QSPI flash: set correct dummy cycles for fast read command
* board subaru: fix connector pinout. again.
* board subaru: fix SDMMC pin configuration
* board subaru: fix DMA conflict SPI4_RX vs SDMMC2
* flash_main.cpp: reorder code for easy integration of ext storage
* Add EFI_STORAGE_INT_FLASH option
Default set to TRUE
* Add ChibiOS's Managed Flash Storage to build
* Add support for QSPI flash (SST26F064A tested)
* board: subaru: enable WSPI and NOR flash drivers
* Add option to save settings on ext flash MFS partition
* board: subaru: store settings on QSPI NOR flash
* big pch energy
* put back ramdisk stub
* tests are happy
* h743 nucleo
* kinetis
* I love deleting code!
* make stepper happy
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* detect hse
* implementation
* these boards don't need to set their own HSECLK
* assertions
* name
* tweaks
* how did this compile?
* s
* biiiig comment
* this script doesn't need to set 25mhz any more
* ....or PLLM
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* CAN HW: use designated initizalization
* board subaru eg33: set CAN transceiver EN to active state constantly
While FW does not handle CAN transceiver's EN signal
* rename
* core
* structing
* more
* makefile
* structing
* 6240 compiles
* explicit cast instead of implicit narrowing
* 8888
* no extern C
* fix tests build
* extern "C"
* 33810
* 8860
* 33810
* linker
* unbreak master
* don't need that if compiling as C++
* bump config
* fix test
* tests
* unit tests bad merge
* build
* move subaru logic to cpp file
* cpp goodness
* hpp include
* this is probably the right thing to do
* simulator
rusefillc
GitHub build-firmware Action
Matthew Kennedy
Scott Smith
Andrey G
Andrey