* We still need consoleEventListener for boards with EFI_CONSOLE_SERIAL_DEVICE
* MC33810: add MC_ prefix for command defines
As CMD_PWM define is now used by console command
* switch to CriticalSectionLocker
* that's just about all
* clean up last usage
* include hpp for sim
* need the cpp wrappers in the makefile too
* include dir
* include
* TLE8888: add support MR switching from SW
Main Relay has limitation - it is always active while KEY=1. When
KEY=0 MR can be switched on from SW.
* TLE8888: support reading of KEY and WAKE inputs
* Rusefi enums: add new TLE8888 pins
* smart gpio: fix tle8888 direct pin mapping for MRE
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888
* TLE8888: cleanup
* TLE8888: do not reset driver private data on WD/undervoltage reset
* TLE8888: diagnostic updates
* TLE8888 driver: BIG driver rework
* TLE8888: check SPI answers for abnormal states
Reply with other than requested register can be a sign of:
-Power-On-Reset, then OpStat0 will be replyed
-WatchDog reset, then FWDStat1 will be replyed
-Invalid communication frame, then Diag0 will be replyed
Keep tracking last accessed register and check with the next reply.
* TLE8888: debug clean-up
* TLE8888: implement spi array write
This reduce CS inactive state time between two consequent accesses
from 8.8 uS to 1.4 uS
* TLE8888: fix PP outputs in OD mode
* TLE8888: cleanup register definitions
* TLE8888: run separate driver thread for each chip instance
Calculating poll interval for few chips become more complex, avoid
this running thread for each device.
* TLE8888: fix cypress and kinetic compilation
Both platforms define its own MAX and cause redifination error if
common.h is included in driver.
* MRE: update mapping.yaml and fix direct pin mapping for TLE8888
* TLE8888: diagnnostic: disable switch off in case of overcurrent
For all output, use current limiting instead
* TLE8888: check for overvoltage on OUT8..OUT13
* TLE8888: add TODO note about how to recover from failure condition
Currently TLE8888 automaticly recovers only from overcurrent and
(may be) overtemperature conditions.
Short to bat cause output disable (bit in OECONFIG is reset) and
needs driver/host intervention.
* TLE8888: save few bytes of RAM
* TLE8888: Lada Kalina is test mule for IDLE stepper on TLE8888
Don't forget to enable PP mode for TLE8888 outputs 21..24:
uncomment line 1087 in tle8888.c
* TLE8888: reorder code, cleanup
* TLE8888: mode all debug/statisctic to per-chip struct
* TLE8888: rework poll interval calculation
* MRE: use TLE8888 pins instead of MCU gpios that drives TLE8888 #2
* second can bus, first steps
* added most important messages; no more errors
* cleaned up can messages
* second can bus, first steps
* added most important messages; no more errors
* cleaned up can messages
* post rebase/merge fixes
* more rebase/merge fixes
* even more rebase/merge fixes
* more fixes, removed auto-gen files
* removed more auto-gen files...
This fixes following build issue under linux:
make: *** No rule to make target 'build/obj/.cpp cj125.cpp', needed by 'build/obj/ build/obj/cj125.o'. Stop.
make: *** Waiting for unfinished jobs....
Introduces in 8d35c35035
* aux serial updates from last PR
* trying to guess
* wow that's old! also not working maybe?
* hiding diag code which was messing with GP2/GP3 i.e. TLE8888_PIN_22 TLE8888_PIN_23
* date
* Mc33 undervolt (#1421)
* mc33 flash check
* DI sanity checks for setting HV config
* mc33 under voltage check
* mc33 under voltage check
Co-authored-by: Christopher W. Anderson <gitstuff@pswitch.com>
* fixed {}
Co-authored-by: rusefi <rusefillc@gmail.com>
Co-authored-by: NOx-z <50815960+NOx-z@users.noreply.github.com>
Co-authored-by: Christopher W. Anderson <gitstuff@pswitch.com>
Co-authored-by: kon <dev@triggerdevel>
* tle8888: fix tle8888_chip_init flow
* tle8888: set correct pin modes for mcu gpios in tle8888_chip_init
Direct drive, reset, inj_en and ign_en gpio should be outputs
* move to can folder
* split out can rx
* only print in debug mode
* guard on feature flag
* split out tx
* headers
* headers
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* move to can folder
* split out can rx
* only print in debug mode
* guard on feature flag
* headers
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* relocate
* include path
* simulator makefile
* fix mre while we're at it
* it would help if I fixed it right
* add can_msg
* convert obd2
* guard properly
* better include order
* docs & headers
* inject CAN device
Co-authored-by: Matthew Kennedy <makenne@microsoft.com>
* pin_repository: provide readable pin names in error cases
* io_pins: remove getBrain_pin_eExt
We have getBrain_pin_eExt in io_pins.cpp and hwPortname in
pin_repository.cpp.
First uses auto-generated enums, second one uses runtime data to
provide name of hw pin.
Removing first saves us about 2K of flash couse big auto-generated
switch with pin names no more used by anyone and gets optimized out.
* gpios: mc33972: CS pin is now requested at smart_gpios.pcc
* getSpiDevice: support SPI4
* smart_gpios.cpp: startSmartCsPins set CSs to inactive state
OutputPin:initPin initializes pin with false value. This is active
state for SPI Chip Selects. Set to 1 to deselect all chips.
* gpio chips: relax error checking on _add
Do not halt whole system if wrong or nulled config is passed.
In current smart-gpio implementation this can happen and it is not
as error. Let smart-gpio handle this, kust reurn negative.
* tle8888: return back includes needed for debug
* smar-gpio: -Werror=missing-field-initializers fix
* smart_gpio.cpp: check _add return values
And occupy gpiochip's pin range if disabled of failed. So base will
align with enum.
* TLE8888: cleanup, move high level code to smart_gpio.cpp
* smart_gpio.cpp: fix compilation when BOARD_EXT_GPIOCHIPS == 0
* board-subaru: fix compilation after latest smart_gpio updates
* tle8888: now we have all 28 pins supported
* efi_gpio: update cached pin value for ext gpios to
* tle6240: update and fix
* gpiochips_init should be called after all gpio chips are added
or we can lost calls to _init of chips
* smart_gpio.c: fix for tle6240 and mc33972
now config structs are not const. waste of ram...
* gpio-chips core function renames
* efi_gpio, pin_repository: add support for external gpios
* gpio-chips update
* gpio-chips: add api to name each pin of gpiochip
* tle6240: provide individual names for each pin
* Some more include fixes for linux
* Pass cross-compile path through CROSS_COMPILE
* Lower-upper case conversion fixes for linux
* Rename unmarkPin to brain_pin_markUnused
This is part of external gpiochip integration
* Add gpio_pin prefix to markUsed and markUnused
To distinguish from similar functions using brain_pin
* pin_repository: add helpers
this is part of gpio chips integration
* efi_gpio: simplify getHwPin using brain_pin_is_onchip
Andrey G
Matthew Kennedy
rusefillc
rusefi
kon
shadowm60
rusEfi
andreika-git
rusefi