4f94c98caa
Provide support for changing the idle stepper direction through the use
...
of an "inverted Y/N" setting. This is to avoid the need to change wiring
if it turns out the stepper is working in the opposite direction to what
is expected.
2019-01-08 11:37:18 +00:00
3293a33f74
fix various typo in ts ini
...
fix selection offset for aux in pins
remove 511 limit on analog
2018-12-29 22:55:02 +00:00
eca00f5719
dec 29122018 master from josh
2018-12-29 17:26:30 +00:00
5431a24e26
Safetyy for existing tunes on the revised trigger edge states
2018-11-27 23:41:00 +11:00
ab07f54fed
Minor tweaks to allowed options for Subaru 6/7
2018-11-23 17:18:37 +11:00
084d07362e
Add Bosch 3 bar MAP sensor
2018-11-18 08:20:22 +11:00
b672a49758
Signature and base tunes for 201810 release
2018-11-15 22:21:31 +11:00
d93fbb96ec
Better handling of default values for ADC filters
2018-11-11 19:25:00 +11:00
8ba2d75f47
ADC filter changes in the ini
2018-11-05 15:58:54 +11:00
2057f05d47
Merge branch 'master' into improved_io2
2018-10-23 10:05:54 +11:00
abb8a085d6
Slightly improved paging on the high speed loggers
2018-10-15 16:27:49 +11:00
9946350a69
Initial testing work on composite logging
2018-10-09 23:31:56 +11:00
fd10a77ff4
New and improved tooth logger
2018-10-01 14:21:13 +10:00
23787d0e21
Merge branch 'master' into improved_io2
2018-09-24 00:49:57 +01:00
207d091f90
resolved further conflicts
2018-09-24 00:41:27 +01:00
90420359f7
improve ini selection robustness to prevent impossible selection according to mcu type etc.
...
allow canbus options to be chosen that were not previously available
2018-09-23 22:50:15 +01:00
40f23ca885
Add safety checks to only set input pin modes when functions are enabled
2018-09-20 07:26:43 +10:00
de5fd0d175
Add configurable analog sensor filters
2018-09-18 17:14:37 +10:00
9bf8c31978
September dev signatures
2018-09-18 16:34:18 +10:00
73f8004cc4
Add staging duty cycle gauge. Confirmed 2S staging ( Closes #162 )
2018-09-17 09:30:48 +10:00
ef4e97e4fe
Display the correct duty cycle for 2 stroke engines. Partially addresses #162
2018-09-11 16:41:12 +10:00
7267ee7a12
Signature and base tunes for August 2018
2018-09-04 17:20:57 +10:00
b555392636
Minor cleanups to missing tooth per tooth calc
2018-09-04 17:07:21 +10:00
0b6b0141f7
Revert the advance table name to old value in ini file. Fixes #160
2018-09-04 13:41:54 +10:00
9e3049d5ec
Add missing knock threshold variable for analog knock input
2018-08-13 09:16:58 +10:00
ee470d8ebd
Remove the value component of the pageReadCommand in ini. Fixes #155
2018-08-13 09:15:55 +10:00
6ad046c398
Additional work on knock control dialogs. Fix for aux in error appearing
2018-08-02 15:25:12 +10:00
20c9c796d6
Initial memory allocation (etc) work for knock control
2018-07-26 22:09:48 +10:00
f1182d569d
Merge branch 'master' into local_auxin3
2018-07-25 16:38:07 +10:00
2287c9086c
Add sync loss counter to log (And apply to other patterns)
2018-07-24 10:44:47 +10:00
dc784deaef
Allow for negative ethanol ignition advance
2018-07-19 17:33:40 +10:00
7bc42b13eb
July dev signatures
2018-07-10 15:13:00 +10:00
94ff7507ec
Remove warnings from June ini file
2018-07-07 09:59:27 +10:00
8dd9ed9fbd
improve TS ini selection options
...
fix bit masking
storage table fix
2018-07-04 01:16:35 +01:00
fbfa727f6f
Merge pull request #60 from noisymime/master
...
update for 03072018 release
2018-07-03 21:51:12 +01:00
87e2cbbde2
Fix default values for AE RPM taper
2018-07-03 22:21:40 +10:00
72397a90e1
Base tune and signatures for June release
2018-07-03 17:31:28 +10:00
5c79f2ac15
Multiple nitrous control fixes. Appears to be working fully. Closes #147
2018-07-03 15:46:23 +10:00
757256bbb7
Merge pull request #59 from noisymime/master
...
update with josh 29062018
2018-06-29 23:15:31 +01:00
a480996cfc
add option to use can channels for local input pins
2018-06-29 23:09:27 +01:00
8ff299e3ac
Initial nitrous control implementation (Needs tweaking and testing)
2018-06-30 01:19:51 +10:00
f276bb7042
Add Fix angle on/off setting
2018-06-29 18:07:39 +10:00
e5ea1ce36e
Allow 6g72 patterns under the new sync method of the 4g63 decoder. #76
2018-06-17 15:16:22 +10:00
3773647062
Initial implementation of AE RPM tapering (Issue #138 )
2018-06-10 14:57:52 +10:00
34e0aca5b6
June Dev signatures
2018-06-10 13:04:57 +10:00
47b7da893e
Base tunes and signtatures for May 18 FW
2018-06-07 15:22:04 +10:00
388ad9ac41
Add UA4C board definition
2018-06-04 16:33:19 +10:00
ecfd621a01
Cleanup boost control settings to disable PID options when using open loop
2018-05-15 14:13:07 +10:00
a694651caa
Add open loop boost option back in
2018-05-15 14:05:45 +10:00
40fb525882
Tidied up ini load units etc for different algorithms
2018-05-15 10:12:26 +10:00
19e258ecfb
Independent fuel and ignition load algorithms
2018-05-08 16:43:18 +10:00
00daa6b93a
Initial Idle Up implementation
2018-05-04 17:55:58 +10:00
50196ce247
May dev signatures
2018-05-02 16:40:57 +10:00
d7599089dc
April 18 signatures and base tunes
2018-05-01 17:40:05 +10:00
ba88cfc07d
Allow negative fixed ignition angles
2018-05-01 17:33:52 +10:00
4b5f580649
All base work on EMAP sensor configuration and reading
2018-04-24 21:31:52 +10:00
d473e00ce4
Groundwork for proper variable algorithms
2018-04-24 17:11:10 +10:00
1d5a79757a
Send through channel and squirt info to TS
2018-04-23 15:27:57 +10:00
68f542405e
Remove unused flex variables
2018-04-13 08:38:24 +10:00
8583e8ac7a
Merge branch 'teensy_reva' of https://github.com/Autohome2/speeduino
2018-04-05 21:42:47 +01:00
339ece2618
add reva and revb teensy boards and enable second o2
2018-04-05 21:41:33 +01:00
818a2416b8
Increase the cranking RPM setting resolution to 10rpm
2018-04-04 14:39:17 +10:00
fec0211da0
Initial work on calculations dashboard
2018-04-01 20:50:45 +10:00
c35ed913a1
March dev firmware sigs
2018-03-14 23:10:30 +11:00
566c20d8e9
Minor wording change for some options
2018-03-12 09:13:19 +11:00
0a8d5e21c5
Feb 2018 signature and base tune
2018-03-10 20:55:21 +11:00
35498b39af
Add analog channels A10-A15 to the fan output drop down
2018-03-01 16:28:58 +11:00
c0ec2cdc02
Disable the cranking advance setting when the Fixed cranking option is used
2018-02-24 15:15:27 +11:00
4c47ea93d3
Add a check that prevents staged injection from trying to run when there are more cylinders than injection channels
2018-02-22 23:10:35 +11:00
684f668c84
changed ini for page 10 unused bytes to match the convention used in other config pages. reformatted the reset control config page section. fixed first element of flex bins not being initialized to 0.
2018-02-17 11:46:42 -06:00
528d3193d8
changed reset control config to use a setting group
2018-02-07 18:37:21 -06:00
8b7f0c345b
Add a loops/rev counter in TS
2018-02-05 12:44:38 +11:00
dfa48ed250
Fix for rare overflow issue that could cause an incorrect pulse width at very low RPM (<200rpm)
2018-02-05 09:39:46 +11:00
e1f2b35081
migrated the flex fuel help to the curve editors. fixed bonehead flexEnabled ini mistake
2018-01-21 15:19:04 -06:00
b5c56495e9
Merge branch 'flextable' of https://github.com/0x15e/speeduino into 0x15e-master-amalgamation
...
# Conflicts:
# reference/speeduino.ini
# speeduino/comms.h
# speeduino/comms.ino
# speeduino/globals.h
2018-01-21 14:55:47 -06:00
9369ec73d8
Merge branch 'reset-lock' of https://github.com/0x15e/speeduino into 0x15e-master-amalgamation
...
# Conflicts:
# reference/speeduino.ini
# speeduino/globals.h
2018-01-21 14:32:51 -06:00
8e789d4644
Merge branch 'master' of https://github.com/noisymime/speeduino into flextable
...
# Conflicts:
# reference/speeduino.ini
# speeduino/globals.h
2018-01-20 18:16:19 -06:00
74fefba9c2
significantly improved the flex settings dialog
2018-01-20 18:00:56 -06:00
23862103e5
extremely rough flex table editors. added flexBoostCorrection to currentStatus. shortened flex correction table names. gave each flex table its own set of eth% bins. fixed the incredibly broken EEPROM update code.
2018-01-20 16:33:14 -06:00
264090863d
Merge pull request #118 from ConnerMcLaughlin/master
...
Launch Control TPS II
2018-01-21 07:18:51 +11:00
929756b63a
Merge branch 'master' of https://github.com/noisymime/speeduino into flextable
...
# Conflicts:
# .gitignore
# reference/speeduino.ini
# speeduino/globals.h
2018-01-19 22:24:02 -06:00
2350d5d785
Table-based flex fuel corrections
...
Changed the linear low / high flex fuel correction method to a table2D-based one.
2018-01-19 21:25:01 -06:00
d07d20ffb8
ini spec version bump to maximum supported by the current stable TunerStudio. removed debug code from comms.ino. updated ini file so that only appropriate options will be shown based on whether the connected Speeduino is using the custom firmware.
2018-01-16 20:02:04 -06:00
b6096329d8
cam4minus1 var is now trigPatternSec
...
All the instances of the variable name cam4minus1 is changed to trigPatternSec
2018-01-15 20:38:37 -06:00
dc0e1c7b88
Correction of choices for cam4minus1 var
...
In speeduino.ini you have to explictly show an INVALID placeholder for all the choices a constant can have. There were only 130 for cam4minus1. The numer was increased to 254.
2018-01-14 21:21:07 -06:00
52701e98ad
Initial commit for missing tooth secondary
...
This also includes setups that have Toyota 36-2+3 trigger wheels to work.
2018-01-14 20:23:25 -06:00
124c0d51da
Launch Control TPS II
...
Adding TPS limit on launch control
2018-01-14 17:42:38 -06:00
27641514f4
Merge branch 'master' of https://github.com/noisymime/speeduino into reset-lock
...
# Conflicts:
# reference/speeduino.ini
2018-01-14 11:29:29 -06:00
2819adb865
Custom bootloader recognition
...
Added a new serial command that allows a custom 16u2 firmware to let the speeduino know about itself. After issuing a `, the speeduino will expect one more byte indicating the capabilities level of the custom firmware (only 1 for now).
2018-01-12 21:37:21 -06:00
dd9941ce5d
Introduce end-of-line normalization
2018-01-12 14:04:43 +11:00
81d8ccd358
Merge branch 'master' of https://github.com/noisymime/speeduino into reset-lock
2018-01-09 18:20:47 -06:00
6c8e238697
January dev signature
2018-01-10 00:11:57 +11:00
43f0d35839
Merge branch 'master' of https://github.com/noisymime/speeduino into reset-lock
2018-01-07 16:22:55 -06:00
ae8ea08d41
Reset Control
...
Changed reset lock feature to a more general "reset control" feature. Moved reset control settings to the general Settings menu. added a serial U command that will halt comms and set the control pin low when another byte is received to facilitate reset control for devices that lack an AtmegaXXu2 usb controller. Improved context help for reset control. Corrected reset lock status indicator on / off labels. moved reset control setup to utils.ino.
2018-01-07 16:22:18 -06:00
f474a95dc5
December 2017 signature and base tunes
2018-01-03 21:52:25 +11:00
9f53002b9d
Adjust injector setting priority so that sequential will override the Simultaneous/Alternating option
2018-01-03 17:27:22 +11:00
03e6c2d476
Software controlled auto-reset prevention
...
This feature enables the Speeduino to set a pin high that will tell the Arduino's 8U2/16U2 firmware not to reset on new serial connections. This requires a slightly modified firmware for the 8U2/16U2 that will only reset on DTR when PB7 is also held low.
2018-01-01 15:39:43 -06:00
8feb7ae521
Fix typo in ini
2017-12-21 23:06:09 +11:00
38dfb2d8f6
Fix for timing bug on Miata 99-05 pattern
2017-12-21 13:30:45 +11:00
36c08d42cc
Initial layout work for 36-2-2-2 decoder
2017-12-15 16:38:17 +11:00
8fe7ff66a9
December dev signature
2017-12-15 16:23:56 +11:00
aebe4d2719
November signature and base tunes
2017-12-10 17:21:55 +11:00
98ea973a80
Add individual pulse widths to the comms output
2017-12-07 11:42:44 +11:00
1e432514f9
Allow separate bars calibration
2017-11-28 10:09:54 +11:00
2989e32f15
Memory adjustments for staging fuel table
2017-11-21 15:17:55 +11:00
f33455229d
Change encoding used on ini file so the latest TS beta (3.0.50.17) can read it
2017-11-16 15:15:47 +11:00
36ca95a330
November dev signatures
2017-11-13 09:14:58 +11:00
883ba4a25f
Potential fix for access enrich overflow
2017-11-08 22:51:40 +11:00
fa5d721b98
October release signatures and base tune
2017-11-07 22:13:27 +11:00
cfb8d20f4e
Fix problem with the AFR correction ignition count not being checked correctly
2017-11-05 19:56:04 +11:00
4b5b040615
Merge pull request #110 from Autohome2/can-serial3
...
Can serial3 updates
2017-11-03 00:00:53 +11:00
380ffc20b8
update serial3 and canbus related data transfer protocols and naming
2017-11-01 20:17:47 +00:00
17030a9df7
Add in check for ignition count to the closed loop AFR control
2017-11-01 16:10:06 +11:00
c7a78ae44f
Fix duty cycle calculation when sequential fuel is used (+formatting of ini)
2017-11-01 13:33:39 +11:00
b67ae45b69
Added NO2C pin mapping
...
Closes #106
2017-10-25 20:55:46 +11:00
1a86a738ed
Add ignition dwell gauge in TS
2017-10-24 21:10:47 +11:00
2ec972948f
Changes to logged variables
2017-10-24 16:54:18 +11:00
6a8ab1015b
Move the pulse width function into the speeduino.h scope
2017-10-24 14:08:32 +11:00
ac4a36529b
Cleanup work in the ini
2017-10-23 22:42:09 +11:00
e921901fc0
Pass fuel pulse width full value to TS
2017-10-10 21:58:03 +11:00
91a428401a
October dev signature
2017-10-10 19:56:37 +11:00
b067ef100b
Signature and base tunes for Sep 2017 release
2017-10-09 12:02:05 +11:00
9202afe7cf
Prevent memory corruption from the page expansion
2017-10-04 12:24:40 +11:00
683fe44562
Initial work on rolling sign cut rev limit
2017-10-04 09:48:46 +11:00
172cd18435
Add explicit on/off mode for the VVT table
2017-10-02 20:01:08 +11:00
c901748974
Allow use of Analog pins for some selectable outputs
2017-10-01 00:07:36 +10:00
7aa8d277f3
Potential fix for cranking problem on Miata 9905 pattern
2017-09-20 16:43:55 +10:00
9d89494666
Expand page 4 to 128 bytes
2017-09-20 12:15:41 +10:00
1cd2a0f296
Expand page 2 to 128 bytes in size
2017-09-19 15:09:32 +10:00
5b3df5ac4d
Merge config pages 6 and 7
2017-09-19 14:51:33 +10:00
6763ff15b4
Initial work on new serial comms protocols (Working, but slow)
2017-09-19 14:10:07 +10:00
1fa85bbbdb
Change wording on boost cut indicator
2017-09-18 10:41:00 +10:00
2d03665162
Remove unused odd fire variable
2017-09-12 14:02:00 +10:00
0694564ed1
September dev signature
2017-09-10 00:51:10 +10:00
d8d1d8ff04
August signature and base tune
2017-09-09 22:07:46 +10:00
7c0932a396
Adjust boost timings slightly
2017-09-07 06:20:22 +10:00
4e858f1ca8
Completed new PID mode for boost control
2017-09-04 11:50:55 +10:00
3b33094230
Initial commit of new Ideal PID implementation (Active for boost control)
2017-09-03 20:28:49 +10:00
bd54aae566
Enable per tooth timing on Nissan 360
2017-08-31 21:04:32 +10:00
e7ac717796
Startup improvements on Nissan 360 CAS
2017-08-31 18:01:37 +10:00
e93bf9f5ac
Fix RPM calc issue on Miata 99-05
2017-08-30 12:53:56 +10:00
a44f36b58c
Small cleanup in ini
2017-08-29 14:18:56 +10:00
4e47e8ae19
Cleanup page 11 array
2017-08-25 17:26:04 +10:00
fc06ce4d1b
Minor ini and comms cleanup
2017-08-24 17:24:28 +10:00
7db1101429
Completely untested trailing spark for FC rotary ignitions
...
May God have mercy on us all
2017-08-23 17:18:59 +10:00
539618c583
Initial interface work on rotary ignition modes
2017-08-23 08:14:11 +10:00
c791302a0e
Harley EVO decoder (courtesy of @bitwise17)
...
Closes #93
Slightly changed to fix bugs and be MISRA compliant
2017-08-17 14:17:21 +10:00
77094a59d1
Better startup procedure and DIY watchdog
2017-08-17 11:24:26 +10:00
345bf5d405
August dev signatures
2017-08-06 22:15:15 +10:00
be9ad6bb85
Fix missing value for TPS calibration
2017-08-06 17:12:57 +10:00
4f7e11c233
Fix for spark miss every ~250 revs
2017-08-06 17:00:58 +10:00
6727b0a750
Activate per tooth timing on dual wheel
2017-08-01 09:39:50 +10:00
523c05fda9
July signature and base tune
2017-07-30 23:07:48 +10:00
9cd31f335f
Cleanup of comms variables
2017-07-27 14:04:38 +10:00
3db9dc99fd
New MAP calculation method (More accurate and allows negative calibration values)
2017-07-27 12:47:59 +10:00
b42d0069ab
Clean up cranking enrichment dialog
2017-07-25 20:42:06 +10:00
e16da51101
Additional work for the new memory page
2017-07-24 14:19:07 +10:00
ccb6e194b7
Initial work creating a new memory page (pg 11)
2017-07-20 16:54:50 +10:00
9d2e938a4d
Initial (mostly untested) live baro reading
2017-07-17 17:06:14 +10:00
905a8642ff
July dev signature
2017-07-17 16:36:44 +10:00
e5591bc7bc
June signature and base tune
2017-07-11 16:21:44 +10:00
a9891ad38c
Fix name of Lambda entry in the log
2017-07-10 11:56:28 +10:00
3d2a692d53
Change freeRam() to unsigned int
2017-07-07 09:26:13 +10:00
1f03499725
further cleanup of ini and msq
2017-07-05 16:02:07 +01:00
d7f374b473
Merge dazq CAN changes
...
Closes #91
2017-07-05 22:28:11 +10:00
5992e31f2f
Experimental commit of per tooth based ignition timing
2017-07-03 18:39:10 +10:00
7f86b91198
Add fields to allow custom MAP sensors being entered
2017-07-03 12:14:07 +10:00
f67f24f16d
Merge pull request #89 from Autohome2/can_io_2
...
External devices over serial3 update
2017-07-02 22:40:45 +10:00
652624b288
Add initial Daihatsu +1 decoder (also 3 cylinder sequential ignition)
2017-06-26 17:34:10 +10:00
8db13859e1
Merge branch 'master' into can_io_2
2017-06-20 02:44:51 +01:00
35dfa6395d
support read values(16channel) from gpio or other external device . other device can also access the speeduino data values(realtime)
...
all via serial3
2017-06-20 02:29:55 +01:00
5c25590f82
Fix warnings for PSIG :)
2017-06-14 18:07:06 +10:00
0296f06438
changes to serial3 protocol and further tidyng with new canserial use
2017-06-13 03:02:50 +01:00
ae7a75673f
June dev signature
2017-06-06 08:32:08 +10:00
4f62900cba
May base tune file
2017-06-05 14:41:58 +10:00
02564d3218
May signature
2017-06-05 14:28:28 +10:00
3dd5ab7370
Tentatively working lambda option
2017-05-27 22:16:42 +10:00
98c3a51ec2
WUE VEAL testing added (Currently disabled)
2017-05-26 13:09:19 +10:00
81c548a9e8
Tentative 6 cylinder support (3000GT) added to 4G63 decoder
...
Requested in #76
Needs testing. Select the decoder and set cylinders to 6.
Note that the Medium and Aggressive trigger filters do NOT currently
work for 6 cylinders and should not be used.
2017-05-16 16:49:35 +10:00
1db7be4a33
Flex fuel boost adder
2017-05-12 18:14:14 +10:00
bcd7b29b59
Merge pull request #86 from Autohome2/can-serial3
...
r command bug fixes and further multiprocessor can and serial3 support
2017-05-11 21:53:19 +10:00
bffb4fb72f
r command bug fixes and further multiprocessor can and serial3 support
2017-05-11 00:08:24 +01:00
cfebe84514
Belated May dev signature
2017-05-10 13:55:26 +10:00
a7460f93d2
Merge pull request #85 from Autohome2/can-serial3
...
serial3 and canbus integration improvements
2017-05-10 12:15:29 +10:00
04a6866115
Allow spark advance values below 0 in the main table
2017-05-09 17:29:55 +10:00
49a23d9a33
This version is based from the can-serial3 branch which was updated from josh's master on 07/05/2017
...
Before change it compiled at
bytes of 63,444 flash(24%) and 4137 bytes of ram(50%) used
upon pr submission this changed to
bytes of 63,574 flash(25%) and 4155 bytes of ram(50%) used
Changes were to allow the use of the "r" command to access specific data in the realtime list
It contains minor changes to the ini file to link to the help for serial3 and can interface.
also change 0x07 to 0x30(dec48) as discussed on slck with josh for the r command
added teensy and stm32 can references and some specific canwork for teensy3.5
need to use pawelsky flexcan library (https://github.com/pawelsky/FlexCAN_Library )
2017-05-08 23:15:03 +01:00
b0d0c40bec
April signature and base tune
2017-05-06 23:43:57 +10:00
fa9f418c35
Resolve all pr/77 conflicts
2017-05-02 21:17:33 +10:00
3f099f06f1
Merge branch 'master' into pr/77
...
# Conflicts:
# reference/speeduino.ini
# speeduino/comms.ino
2017-05-02 12:25:51 +10:00
4380f8b0d5
Move to TS optimised serial comms model + many minor serial improvements
2017-04-22 23:31:13 +10:00
71e963e196
Log dwell as a float rather than an int
2017-04-22 10:03:10 +10:00
538bc5f0bf
Initial commit of dwell limiting when it exceeds maximum time in revolution
2017-04-21 17:29:09 +10:00
ac37fafc84
April dev firmware
2017-04-15 08:40:29 +10:00
9bff58a265
added 8ch input over serial3 , displays data in TS live and logs to TS log file.
...
Data format follows j1939 type methods , see protocol doc
2017-04-09 01:17:36 +01:00
5d031a0fc9
Signature and base tune for March
2017-04-03 16:12:24 +10:00
34b9adb777
Add stepper idle disable function for DRV8825
2017-04-02 21:17:29 +10:00
676a001fb8
Initial commit of Subaru 6/7 (Likely has bugs)
2017-03-31 22:39:33 +11:00
822c400c01
Fix for potentially wrong initialisation of the on/off idle control
2017-03-30 00:01:52 +11:00
e96feaa560
Add VW/Audi/Porsche MAP sensor
2017-03-29 20:51:11 +11:00
4897e44f55
Merge branch 'master' into pr/73
...
# Conflicts:
# reference/speeduino.ini
# speeduino/comms.h
# speeduino/comms.ino
# speeduino/globals.h
2017-03-25 09:17:06 +11:00
8fc87e062a
Fixes for closed loop stepper idle (Now ready for wider testing)
2017-03-22 12:44:22 +11:00
697e3a2c17
Add option to disable resync once every cycle (Dual wheel, Audi 135 and 4G63)
2017-03-21 17:19:07 +11:00
880947746f
Many small updates to the idle system (Including additional logging)
2017-03-20 22:29:42 +11:00
c28547dc3a
Add a bunch more values to the log output (Including boost duty)
2017-03-16 18:17:12 +11:00
35e67e5ee6
Fix incorrect memory addresses in ini for boost and flex
...
Fix still required for developer brain fart.
2017-03-13 17:02:54 +11:00
31836511a3
Initial closed loop stepper idle (Not quite complete)
2017-03-10 20:34:39 +11:00
abef8df43f
Fix warnings in TS due to unterminated sentences
2017-03-10 13:16:56 +11:00
74cf93b979
add test modes to injector and spark outputs
2017-03-10 00:46:11 +00:00
d686364e69
March dev signature
2017-03-08 13:19:30 +11:00
a0ede949b7
Base tune and signature update for Feb release
2017-03-03 12:51:34 +11:00
707d65cac8
Shuffle around memory to make upgrades simpler
2017-02-26 16:33:03 +11:00
2e5a45463b
Additional default pins to prevent weirdness on upgrades
2017-02-21 16:51:50 +11:00
0d055dc7f1
Allow min and max duty cycles for closed loop idle and boost
2017-02-20 17:57:46 +11:00
650a096175
Initial (untested) commit of Nissan 360. ONLY support 4 cylinder so far
2017-02-12 18:35:18 +13:00
667e80dc26
Add boost target to log
2017-02-12 14:31:37 +13:00
ced30ce3a7
Remove PSI Boost option from TS
2017-02-09 14:26:21 +11:00
0fc212ec11
Remove all traces of PSI based boost targets
...
The metric conspiracy lives! Muhahahahahah
2017-02-09 14:24:07 +11:00
74137338e5
February dev signature
2017-02-09 09:54:25 +11:00
b2ca13c9aa
Merge pull request #64 from Autohome2/can-io
...
Can io
2017-02-05 21:42:33 +11:00
dd92c40af4
Base tune and signature for Jan 2017
2017-02-01 17:42:11 +11:00
294192c52c
Merge branch 'master' into master
2017-01-30 20:13:33 +11:00
425ec75828
Remove selectable pin options from being on pins 1/2 (Comms pins)
2017-01-28 08:39:10 +11:00
9011c190e0
Fix for fan hysteresis not operating correctly
2017-01-27 16:38:52 +11:00
656fc8b77a
added page 10 , a 128byte page for use with upcoming CANBUS integration.
2017-01-26 22:58:21 +00:00
ad825c2051
Allow for use of negative advance (i.e. ATDC) values for launch
2017-01-21 12:58:45 +11:00
770da8b43e
Selectable boost and VVT pins
2017-01-19 14:54:07 +11:00
2ee0a91c0b
BIG cleanup of #includes to be more C compliant
2017-01-18 17:37:55 +11:00
4c1c9a051e
Slightly improved flat shift / launch logic
2017-01-18 13:20:04 +11:00
da3f460152
Don't cutoff the decimal values of afrTarget in data logs
2017-01-18 10:24:20 +11:00
109f64f342
Memory allocation and TS interface for flat shift
2017-01-17 13:33:41 +11:00
0e176f0724
Enable MAP load values up to 511
2017-01-17 10:51:53 +11:00
6b368e998d
Add more pressure gauge options (PSI, inhg)
2017-01-16 14:41:40 +11:00
e58ad87ed2
Add check to prevent potential crash when switching IAC methods (Teensy)
2017-01-12 22:33:26 +11:00
251000893c
Jan 17 dev signature
2017-01-06 08:26:11 +11:00
7d70f688aa
Signature and base tune for Dec 2016 release
2017-01-05 17:20:54 +11:00
7a87363618
Add MAP x RPM variable to datalog
2017-01-04 22:34:25 +11:00
6c17cde092
Better AE curve range
2017-01-01 19:56:18 +11:00
a80ff171f5
Actually remember to allow 5 cylinder selection in TS
2016-12-29 08:46:20 +11:00
6ac8807399
Global injector closing angle TS setting
...
Adding TS setting in "Injector Characteristics"
2016-12-27 13:35:46 -06:00
b3a04cc19b
Expose some pieces of flex info to TunerStudio
2016-12-26 20:53:37 +11:00
48712c12fa
Add settings to select pins for fuel pump and fan
2016-12-21 13:21:27 +11:00
9889a1ff18
December dev signature
2016-12-11 23:48:41 +11:00
397fb56445
Remove 2 default values that aren't used any more
2016-12-11 22:49:48 +11:00
fd9a140374
Signature for November release
2016-12-05 20:44:25 +11:00
022e82d66f
Minor changes to TS AE dialog
2016-11-30 17:17:51 +11:00
049f3081b1
Complete fuel correction for flex
2016-11-28 20:37:24 +11:00
aac73d785b
Further groundwork for flex fuel adjustments
2016-11-28 16:58:24 +11:00
8540f64620
New flex fuel dialog
2016-11-27 21:47:22 +11:00
e7113b03a1
Enable injector angle options for cyls 3/4 when sequential is selected
2016-11-24 07:05:57 +11:00
6921107373
Development signature for Nov (Late)
2016-11-18 14:31:03 +11:00
Richard Metcalfe
darren siepka
Josh Stewart
Autohome2
Murray
ConnerMcLaughlin