This resulted in the removal of duplicate logic, duplicate code and the
removal of a temporary buffer per-driver.
The NAZE specific sensor alignment is now contained within the core code
instead of in the drivers.
The sensor alignment is determines by the sensor initialisation code.
The alignment of sensor readings is now performed once and only by the
appropriate sensor code, see usages of alignSensors().
The acc/gyro/compass driver code is now more reusable since it has no
dependencies on the main code.
each. relocated acc_t/gyro_t from sensors_common.h into
drivers/accgyro_common.h since they define an interface and the
dependency was pointing the wrong way from the drivers.
baro_t/acc_t/gyro_t dependences are all now pointing the right way.
the code is doing. There are now no EEPROM read/write/reset/verify
methods that take any arguments which removes magic boolean variables
from method signatures.
This also removes duplicate code in the cliDefaults and cliSave commands
which results in smaller code also also due to the deduplication of a
reboot message.
only what it's name implies and it's method takes no arguments. This
avoids the 0/1 magic numbers which was a flag to decide whether the user
should be notified after the EEPROM has been read (!).
Introduced a method called readEEPROMAndNotify() which is used in all
cases where writeEEPROM(1) was previously called.
Additionally this avoid re-reading the profile when the reboot command
is issued which speeds up reboots.
Finally this avoid needless comments because the code tells you now what
it is going to do.
serial_common.c/h. decouple runtime_config from serial ports. decouple
buzzer from serial ports. decouple opening of the main serial port from
the msp code. decouple serial rx providers from runtime_config. rename
core_t to serialPorts_t since it only contained serial ports. It's now
clear which files use serial ports based on the header files they
include.
of determining a revision code. Previously there was mpu6050 specific
code in cli.c (the status command).
Finally this commit has removed all non-serial port configuration
settings from core_t so that a future commit can refactor core_t to
reduce dependencies on serial port code.
In doing this I also noted from other source code that the MPU6050
accelerometer trim for some revisions appeared to be incorrectly set to
255 * 8 instead of 256 * 8.
and by the mixer. main.c now asks the mixer if it needs to use servos
and the mixer decides this in mixerInit(). Main already has a
dependency on the mixer. This allows future commits to further clean up
core_t which is still a source of dependency problems.
index instead of a servo middle when using MSP_SET_SERVO_CONF.
Old GUI clients can still be used to SET channel forwarding, but cannot
be used to READ the status of channel forwarding until they are updated
to use MSP_CHANNEL_FORWARDING/MSP_SET_CHANNEL_FORWARDING.
To the user it will mean their GUI may not match the stored
configuration. However there is no way to DISABLE channel forwarding
other than a reset if they have enabled it using an old client.
This situation is not ideal, but without this commit it would mean that
bad data could be stored and used incorrectly by baseflight if a user
enables channel forwarding using an old client.
capability flag which is returned by MSP IDENT (CAP_CHANNEL_FORWARDING).
Adds two new MSP commands that are specifically for configuring channel
forwarding (MSP_CHANNEL_FORWARDING/MSP_SET_CHANNEL_FORWARDING). Servo
'middle' and 'forward from channel' are now stored independently, as
they probably should always have been.
channels when using Spektrum 2048 - untested. Renamed and extracted
core_t.numRCChannels to rxConfig.channelCount so that future commits can
clean up core_t further since core_t contains completely unrelated
properties.
code into rx_common.c. Moved some GPS code into gps_common.c. Isolated
some GPS functions into gps_common.c that were called from mw.c/loop().
moved gimbal defines into gimbal.h. Moved sound & light code into
statusindicator.c
remove dependency on board.h and mw.h on a few files.
Moved rx configuration paramaters into rxConfig in order to remove the
dependency on config_t from the sbus rx code - sumd/spektrum to follow.
Avoided use of YAW/PITCH/ROLL in some files since those constants are
from an unrelated enum type.
Replaced some magic numbers with constants to remove comments and
improve code readability.
Note, due to the tight coupling and global variable usage it was
difficult to create a smaller commit.
Dominic Clifton
dongie
treymarc