Call targetConfiguration() once before config is loaded and again afterwards in case the config needs to be changed to load from SD card etc
Drop SPI clock during binding
Remove debug
Add per device SPI DMA enable
Fix sdioPinConfigure() declaration warning
Reduce clock speed during SPI RX initialisation
First pass at GHST driver including low-latency control, and basic telemetry.
Fix Ghost channel scaling
Use ghstChannelData instead of rxRuntimeState->channelData
Integrate PR feedback
Primarily de-tab and a few cosmetic changes.
Keep Travis CI happy
Removed unused function
Rework ghost driver to reduce time in ISR, move processing
As requested in PR review.
Fixed issue in telemetry driver, mAh consumed is transmitted as units of 10mAh, not 1mAh.
Resolve Packet Collision Issue with GHST
Send telemetry packets only within a well defined time slot after an incoming Rx packet.
Remove unnecessary comment
rxRefreshRate doesn't need to be dynamic.
Ghost - Remove special case from scheduler
No need to reschedule telemetry for the Ghost protocol.
Eliminated the duplicated MSC functions in the architecture specific files and moved to a shared common.
Improved the activity indicating LED and made it consistent between onboard flash and sd card mass storage mode.
F405 working (OMNIBUSF4SD target)
F411 not tested
F722 working, needs testing (OMNINXT7 target)
F74x not working
NOX target (temporary)
bb_dshot with telemetry on f4
bbshot f7 targets and fix crash due to missing debug pins
remove empty line
add empty lines
remove OMNIBUSF4 specific debug pins
add missing comma
add missing comma
Use separate bbTimerHardware array to fix unified targets
eliminate now unneeded timerGetByUsage
don't duplicate timer1 def
Add auto mode, rename dshot_bbshot to dshot_bitbang
remove newline
renamve various files
various changes to address feedback
address feedback
address feedback
add pacer timers to timer show
don't disable telemetry if dshot_bitbang is on or auto
Address feedback, add faster decode implementation based on bit banding, modify dma parameters to reduce required memory bandwidth on half
remove debug output
remove NOINLINE
Protect gpio direction change with critical sections
FIXWS_SAVE_INDEX
add static back in
no forward typedef
address review feedback
disallow proshot1000 with dshot bitbang
Extracted and plumbed up 'dbgPin'.
- Initial
- Adjust load address of EXST firmware.
- Add helper script to pad an EXST binary to the expected size.
Padded firmware currently required due to a bug in the flash/dfu code
which causes anything less than a flash page size to be truncated when
uploading new firmware via the bootloader DFU.
- Minor linker script cleanups.
- STM32H7.mk change hardcoded TARGET_FLASH (384) to FIRMWARE_SIZE
- Delete unused configuration section entries from linker
scripts.
- Increase EXST firmware size to 448K.
It turns out 384K wasn't enough for a feature-complete firmware.
- Update pad-exst.sh to use 448K by default.
- Move the EXST file generation to the makefile.
[EXST] Embed firmware hash in ELF
- Add debug marker at end of CODE_RAM section.
It was found when transferring firmware to the H7 RAM via a BMP probe
using the 'gdb load' command, that the last few bytes were not
transferred, this debug marker is present to ensure all needed parts of
the firmware are present.
Example memory view of corrupted bytes at end of transfer:
0x2407DFAE DEB90000 DEB9DEB9 DEB9DEB9 DEB9DEB9 ..¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ
0x2407DFBE 000000B9 00000000 00000000 00000000 ¹...............
should be:
0x2407DFAE DEB9DEB9 DEB9DEB9 DEB9DEB9 DEB9DEB9 ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ
0x2407DFBE 00000000 00000000 00000000 00000000 ................
- Remove debug marker in EXST firmware.
STM32H750_EXST - Provide space for empty hash.
* Bootloader will run firmware if hash is empty, without re-verifying
RAM content against hash.
* CODE_RAM always shows as 100% usage.
STM32H750_EXST - Use a specific ELF section for a hash.
Two benefits:
1) CODE_RAM no-longer shows 100% full, since it is no-longer
padded/filled.
2) Prepares the code so that objcopy can be used to inject the hash
into the ELF.
STM32H750_EXST - Patch MD5 into ELF.
Process is now as follows.
* Binary generated (via make target dependency) so there is something to
hash.
* Binary copied (and padded).
* MD5 Hash computed.
* xxd patch file generated from hash.
* xxd hash patch applied to copy of binary at correct address.
* elf .exst_hash section dumped.
* hash injected into into dumped section.
* elf .exst_hash section updated with updated dumped section.
Replace EXST with USE_EXST.
Add documentation for the EXST firmware format.
Add table formatting to EXST documentation.
Update bootloader block.
Update H750 EXST linker script to use block format 0x00.
Use .exst.elf and .exst.bin on the exst files.
Add 'no checksum' to list of checksum hash methods.
Update EXST build system so it generates the following sets of files
obj/main/betaflight_TARGET.elf
obj/main/betaflight_TARGET.map
obj/main/betaflight_TARGET_EXST.elf
obj/betaflight_VERSION_TARGET.bin
obj/betaflight_VERSION_TARGET.bin.md5
obj/betaflight_VERSION_TARGET_EXST.bin
Update EXST build system to be more user-friendly.
* user-flashable files are generated in the normal place.
* Intermediate files are generated in `obj/main/...`
* Removes the `exst` goal.
* Adds .hex generation for EXST builds based on the patched .elf.
To build EXST targets, simply use `make TARGET=x` as normal and flash
the resulting `.hex/.bin` files rather than the .exst.bin file.
Developers can use either the `.elf` or patched `_EXST.elf` file as is
appropriate for their needs.
EXST documentation updated to match changes to build system.
Basic system files
- Initial system files
- Additional RCC clock enables for testing
- Coding style tidy (target/system_stm32h7xx.c) and enable MCO for testing
- Clock generator changes for SPI support
- Setup MPU for "D2 SRAM as write-through by MPU, call it DMA_RAM"
- Drop USB clock enabling from driver/system_stm32h7xx.c
- stm32h7_hal_conf.h for persistent object storage
Basic build files
STM32H7.mk changes
- STM32H7.mk for USE_UART and USE_SERIAL_RX
- Modify STM32H7.mk for inclusion of SPI driver
- STM32H7.mk change for D2 SRAM as write-through by MPU, call it DMA_RAM
- STM32H7.mk for DMA facility
- STM32H7.mk for [TIMER] For "Initial cut without Dshot"
- STM32H7.mk change for [LED_STRIP] Add LED_STRIP
- STM32H7.mk for [ADC] Initial cut without internal sensors
- STM32H7.mk for Enable I2C (HAL)
- STM32H7.mk for "Enable HAL-based DShot (no burst yet)"
- STM32H7.mk change for transponder
- STM32H750 - Add platform support.
- STM32H750 - Add H750 MCU ID.
- STM32H743 - Add MCU ID.
STM32H7.mk change for "Burst Dshot First working version"
Fix boot loader request
STM32H750 - Add PERSISTENT memory support.
STM32H743 - Add PERSISTENT memory support.
Use PERSISTENT memory for bootloader request.
Using DTCM RAM did not work on H750.
Change flash latency from 4WS to 2WS
STM32H750 - Fix reset of RCC_CR to reset value.
Note: The comment above the code didn't match code.
STM32H750 - Remove duplicate startup code, see SystemClock_Config.
STM32H7.mk changes for Port RTC backup register based persistent storage for H7
Make use of persistent object facility
Force reboot after possible boot loader activity
Enable CRS
stm32h7xx_hal_conf.h for H7 - QuadSPI support
stm32h7xx_hal_conf.h for STM32H7 - SDCard/SDIO using HAL Driver
stm32h7xx_hal_conf.h : Fix systick to be 0x00 instead of ST's default 0x0F.
This fixes the ability to use HAL_Delay() from an ISR, as required by
the ST's USB Library.
Specifically, systick handler must be a higher priority than the USB
FS/HS Interrupt handler priorities.
stm32h7xx_hal_conf.h for Add PID-Audio support
source.mk for H7 - QuadSPI support
drivers/system_stm32h7xx.c for H7 - QuadSPI support
STM32H7.mk for H7 - QuadSPI support
STM32H7.mk change for CDC-HID support
common_pre.h updates
- Scheduler parameters to same as F4 & F7
- Enable some important default features
- STM32H7 - Enable ITCM RAM.
Requires voltage scaling fix from commit
6e684c609310024141c43de484a5e78103140e3c
STM32H750 - Disable caches before reboot.
Prior to this when EEPROM_IN_RAM was used the persistent data section
would have corruption immediately after a reboot, prior to even the
Reset_Handler code having been executed.
drivers/system_stm32h7xx.c Touch-up after 2019-02-02 rebase
STM32H7 - Write protect ITCM ram.
Remove local defs for RESET_xxx symbols
STM32H750 - EXST firmware reboots to FLASH bootloader, rather than ROM bootloader.
STM32H750 - Disable some MCO/clock testing code as the pins interfere with new targets.
STM32H750 - Don't disable data caches after bootloader.
Observed that disabling dcache after cold boot with BOOT pin high causes
segfault.
drivers/system_stm32h7xx.c for STM32H7 - SDCard/SDIO using HAL Driver
drivers/system_stm32h7xx.c change for Move SDMMC clock init into SDIO driver
drivers/system_stm32h7xx.c: Cleanup some Clock/MCO/GPIO initialisation code.
drivers/system_stm32h7xx.c for Reset if systick is stuck.
STM32H7 - Fix missing CPU voltage scaling.
It appears this was the cause of other seemingly random issues:
* Crash soon after enabling USB.
* Flash write failures.
* Random un-explainable crashes.
Change RCC_HSE_BYPASS to RCC_HSE_ON
Even Nucleo-H743 seems to work without setting HSE_BYPASS.
STM32H7xx - Move memory section initialisation earlier into the init sequence.
Allows startup-code/libs/etc to be moved into different memory regions.
Don't touch vector table in EXST targets
STM32H750_EXST - fix boot loop
target/system_stm32h7xx.c for STM32H7 - SDCard/SDIO using HAL Driver
target/system_stm32h7xx.c change for Fix SD card clock speed selection
STM32H750_EXST - Reset MPU regions on boot.
* Failure to reset regions will result in mem-fault if bootloader has
configured a similar region.
STM32H750 - Fix missing include of platform.h in system_stm32h7xx.c
This caused the SDMMC peripheral clock to be un-configured (at reset
state) when USE_SDCARD_SDIO was defined.
Change MPU region number for DMA_RAM from 0 to 1
Avoid conflict with ITCM-RAM write protection.
STM32H7xx - HSERDY slow/stuck workarounds.
STM32H7xx - Fix region MPU number for SDIO.
* It was overwriting the previous region causing LED strip and
transponder issues.
Target/system_stmh7xx.c for Reset if systick is stuck.
startup/system_stm32h7xx.c change for non-caching DMA_RAM
H750 - Use SIZE optimization by default due to limited flash space.
STM32H7.mk for STM32H7 - SDCard/SDIO using HAL Driver
STM32H7.mk updates
- Decrease HSE_STARTUP_TIMEOUT to 1 second
* default is 5 seconds, which is too long when HSE gets stuck.
- Add PID-Audio support
Temporary override LINKER_DIR
* Revert "Revert "Rewritten F7 dshot to LL (draft)" (#5430)"
This reverts commit aa42a69d2f.
* Reworked F7 linker scripts to maximize performance of both F74x and F72x
* Some comments and changes from original F7 HAL DSHOT
* Prohibit inlining of some functions to place them in ITCM-RAM
* Fixed usartTargetConfigure implicit declaration
* Moved back to SRAM1 as main RAM
* Added SRAM2 attribute
* Fixed LL DSHOT FOR SPRF7DUAL and probably other adv TIM users
* Fixed SPRF7DUAL rev. A motor order
* Enabled CCM for data on F40x
* Fixed F7 startup assembly symbols
* Fixed KISSFCV2F7 linker script
* Added a quick way of building F7 targets only
* Got rid of the useless F7 target script
* Added NOINLINE and got rid of useless __APPLE__ define
* Added some important functions to ITCM
* Added NOINLINE macro for tests
* Copy to ITCM before passing execution into it
* Minimized cache footprint of motor output code
* Evicted low-impact functions from ITCM
* Switched MATEKF722 and SPRACINGF7DUAL to burst DSHOT
* Switched CLRACINGF7 to burst DSHOT
* Moved UART RX&TX buffers to DTCM-RAM to avoid cache incoherency
* Marked taskMainPidLoop for ITCM-RAM, disallowed inlining per-function
* Revert "Added a quick way of building F7 targets only"
This reverts commit 22945189980deaf493be54a5056a080e7edad629.
Steve Evans
Hans Christian Olaussen
mikeller
jflyper
Steve Evans
Unknown
Dominic Clifton
Bruce Luckcuck
Thorsten Laux
blckmn
Andrey Mironov
jflyper
Chris