+ this is a per-profile setting, and PIDs CHANGE from default multiwii ones. check the above forum post for PID examples. set pid_controller = 0 for default multiwii, or 1 for new one.
= went back to clearing clibuffer after each command
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@341 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added and began work on integrating failsafe_detect_threshold
got rid of acc_lpf_for_velocity since that seemed no longer used.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@317 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
Conflicts:
src/board.h
src/main.c
Conflicts:
src/main.c
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
Disabling PWM2 as an input as it conflicts with the yellow onboard LED2.
PWM and ADC configuration is the same as the naze32 for now. Requires an accelerometer is connected via I2C2.
I2C signals SDA2 and SCL2 are on the UEXT header (Pins 6 and 5 respectively)
USART signals TX and RX are on the CON3/CON4 headers (TX = D7, RX = D8)
Onboard LEDs (LED1/LED2) working.
Buzzer support removed for now as it conflicted with PWM map and LEDs.
mma845x support disabled as it conflicted with an LED.
Relocated some NAZE specific comments.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@302 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
defaulted to looptime of 3500 (yea, yea)
rewrote baro stuff to match mwc2.2 - both supported sensors now return temperature and pressure, which is used in altitude calculation code
rewrote hmc5883 driver to include calibration inside the driver file instead of calling parts of calibration from userspace. it will now blink LED1 while calibrating
some parts remaining to do.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@298 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
mw2.2-merged stuff:
* implemented profiles 0-2 (called 'setting' in mwiigui)
* merged in MSP changes including profile switch
* cleaned up rc / aux switch stuff in mw.c based on 2.2 rewrite
* main loop switch for baro/sonar shit adjusted
todo: basically the rest of 2.2 changes (i think some minor imu/gps/baro updates)
baseflight-specific stuff:
* made boxitems transmission dynamic, based on enabled features. no more GPS / camstab trash if it's not enabled
* cleaned up gyro drivers to return scale factor to imu code
* set gyro_lpf now controls every supported gyro - not all take same values, see driver files for allowed ranges, in case of invalid lpf, defaults to something reasonable (around 30-40hz)
maybe couple other things I forgot. this is all 100% experimental, untested, and not even flown. thats why there's no hex.
merge is still ongoing.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@294 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
added sending cell voltages (faked) via frsky telemetry by fiendie
two additional cli commands (aux and dump) from jef79m - aux allows setting switches from command line, dump creates a copy-pasteable config which can be sent to a new board.
git-svn-id: https://afrodevices.googlecode.com/svn/trunk/baseflight@283 7c89a4a9-59b9-e629-4cfe-3a2d53b20e61
timecop@gmail.com
Dominic Clifton
bouwens.mehl@gmail.com