SPRACINGH7EXTREME - Disable requirement for custom gyro alignment and
dual gyro.
Requires custom gyro rotation code to be merged first, see:
https://github.com/betaflight/betaflight/pull/7845https://github.com/betaflight/betaflight/pull/8474
SPRACINGH7EXTREME - Add boards documentation and images.
Add SPRacingH7EXTREME to the list of official targets.
SPRACINGH7EXTREME - Add unified target config.
Note: untested as no unified target exists for STM32H750+EXST yet.
SPRACINGH7EXTREME - Use correct gyro settings now that #8474 is merged.
SPRACINGH7EXTREME - Combine target files.
SPRACINGH7EXTREME - Update unified target config.
- Initial
- Adjust load address of EXST firmware.
- Add helper script to pad an EXST binary to the expected size.
Padded firmware currently required due to a bug in the flash/dfu code
which causes anything less than a flash page size to be truncated when
uploading new firmware via the bootloader DFU.
- Minor linker script cleanups.
- STM32H7.mk change hardcoded TARGET_FLASH (384) to FIRMWARE_SIZE
- Delete unused configuration section entries from linker
scripts.
- Increase EXST firmware size to 448K.
It turns out 384K wasn't enough for a feature-complete firmware.
- Update pad-exst.sh to use 448K by default.
- Move the EXST file generation to the makefile.
[EXST] Embed firmware hash in ELF
- Add debug marker at end of CODE_RAM section.
It was found when transferring firmware to the H7 RAM via a BMP probe
using the 'gdb load' command, that the last few bytes were not
transferred, this debug marker is present to ensure all needed parts of
the firmware are present.
Example memory view of corrupted bytes at end of transfer:
0x2407DFAE DEB90000 DEB9DEB9 DEB9DEB9 DEB9DEB9 ..¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ
0x2407DFBE 000000B9 00000000 00000000 00000000 ¹...............
should be:
0x2407DFAE DEB9DEB9 DEB9DEB9 DEB9DEB9 DEB9DEB9 ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ¹Þ
0x2407DFBE 00000000 00000000 00000000 00000000 ................
- Remove debug marker in EXST firmware.
STM32H750_EXST - Provide space for empty hash.
* Bootloader will run firmware if hash is empty, without re-verifying
RAM content against hash.
* CODE_RAM always shows as 100% usage.
STM32H750_EXST - Use a specific ELF section for a hash.
Two benefits:
1) CODE_RAM no-longer shows 100% full, since it is no-longer
padded/filled.
2) Prepares the code so that objcopy can be used to inject the hash
into the ELF.
STM32H750_EXST - Patch MD5 into ELF.
Process is now as follows.
* Binary generated (via make target dependency) so there is something to
hash.
* Binary copied (and padded).
* MD5 Hash computed.
* xxd patch file generated from hash.
* xxd hash patch applied to copy of binary at correct address.
* elf .exst_hash section dumped.
* hash injected into into dumped section.
* elf .exst_hash section updated with updated dumped section.
Replace EXST with USE_EXST.
Add documentation for the EXST firmware format.
Add table formatting to EXST documentation.
Update bootloader block.
Update H750 EXST linker script to use block format 0x00.
Use .exst.elf and .exst.bin on the exst files.
Add 'no checksum' to list of checksum hash methods.
Update EXST build system so it generates the following sets of files
obj/main/betaflight_TARGET.elf
obj/main/betaflight_TARGET.map
obj/main/betaflight_TARGET_EXST.elf
obj/betaflight_VERSION_TARGET.bin
obj/betaflight_VERSION_TARGET.bin.md5
obj/betaflight_VERSION_TARGET_EXST.bin
Update EXST build system to be more user-friendly.
* user-flashable files are generated in the normal place.
* Intermediate files are generated in `obj/main/...`
* Removes the `exst` goal.
* Adds .hex generation for EXST builds based on the patched .elf.
To build EXST targets, simply use `make TARGET=x` as normal and flash
the resulting `.hex/.bin` files rather than the .exst.bin file.
Developers can use either the `.elf` or patched `_EXST.elf` file as is
appropriate for their needs.
EXST documentation updated to match changes to build system.
delay for voltage warnings #6691
changed to vbat
Update Battery.md
Add Menu osd Alarm delay
vbat_duration_for_crit
batteryConfig_vbatDurationForCrit
to
vbat_duration_for_critical
batteryConfig_vbatDurationForCritical
lastVoltageOkMillis rename
Updated the existing 3.5.x maintenance branch SYNERGYF4 target to be 4.0 and unified target compatible.
Including:
- Legacy target for 4.0
- Unified target for future releases
- Documentation
The currently listed version (5.4.1) is insufficient, version 7.3.1 (represented as 7-2018-q2-update) is expected in make\tools.mk (GCC_REQUIRED_VERSION ?= 7.3.1)
Add msp code 238.
Add MSP_MODE_RANGES code to msp.c.
Add 2 extra byte reads to MSP_SET_MODE_RANGES.
Add check for extra bytes in MSP_SET_MODE_RANGES
Add API documentation for MSP_MODE_RANGES_EXTRA
convert linkedTo storage to boxid
Send length of array in EXTRAS data
Add note that alignment of elements of MODE_RANGES and MODE_RANGES_EXTRA is required and indicated by permanentId.
mikeller
SteveCEvans
Reinhard
x4FF3
unknown
azolyoung
Andrey Mironov
Merak RC
Dominic Clifton
Kyle Kienapfel
Phong Vu
functionpointer
MJ666
blckmn
swilkens
laz2wiringpi
david
Lexio
elin-neo
Markus Pyykkö
IflightRc
Nick Hesson
Konstantin Salavatov
Dave Huber
Pieter Kruger
Asizon
Dominic Clifton
Kurt Wilson